798315
18
Verklein
Vergroot
Pagina terug
1/36
Pagina verder
EN-6 452115.66.26 FD 9404
WPM Econ5
English
4 Electrical installation work for the heat pump
4.1 Electrical installation work
1) The up to 5-core electricity supply cable for the power
element of the heat pump is fed from the electricity meter of
the heat pump via the utility blocking contactor (if required)
in to the heat pump (see heat pump manual for the supply
voltage).
The power supply for the heat pump must contain an all-pole
shut-off with a contact opening distance of at least 3 mm
(e.g. utility blocking contactor, power contactor), as well as
an all-pole circuit breaker with shared triggering of all outer
conductors (release current and characteristics in
accordance with device information).
2) The three-core electricity supply cable for the heat pump
manager (heating controller N1) is fed into the heat pump
(devices with integrated controller) or to the future mounting
location of the heat pump manager (WPM).
The (L/N/PE~230 V, 50 Hz) supply cable for the heat pump
manager must have a constant voltage. For this reason, it
should be tapped upstream from the utility blocking
contactor or be connected to the household current, as
important protection functions may otherwise be lost during
a utility block.
3) The utility blocking contactor (K22) with 3 main contacts (1/
3/5 // 2/4/6) and an auxiliary contact (NO contact 13/14)
should be dimensioned according to the heat pump output
and must be supplied by the customer. The NO contact of
the utility blocking contactor (13/14) is looped from terminal
strip X3/G to connector terminal N1-J5/ID3. CAUTION! Low
voltage!
4) The contactor (K20) for the immersion heater (E10) of mono
energy systems (HG2) should be dimensioned according to
the radiator output and must be supplied by the customer. It
is controlled (230 V AC) by the heat pump manager via
terminals X1/N and N1-J13-NO4.
5) The contactor (K21) for the flange heater (E9) in the
domestic hot water cylinder should be dimensioned
according to the radiator output and must be supplied by the
customer. It is controlled (230 V AC) by the heat pump
manager via terminals X1/N and N1/J13-NO5.
6) The contactors mentioned in points 3, 4 and 5 are installed
in the electrical distribution system. The mains cables for the
heating elements should be dimensioned and protected
according to DIN VDE 0100.
7) The heat circulating pump (M13) is connected to terminals
X1/N and N1/J13-NO5.
8) The domestic hot water circulating pump (M18) is connected
to the terminals X1/N and N1/J13-NO6.
9) The return sensor is integrated into air-to-water heat pumps
for outdoor installation, and is connected to the heat pump
manager via the control cable. The return sensor must be
installed in the immersion sleeve in the manifold only when
a dual differential pressureless manifold is used. The single-
core wires are then connected to terminals X3/GND and X3/
R2.1. The link cable A-R2, which is positioned between X3/
U2 and X3/1 in delivery state, must then be switched to
terminals X3/1 and X3/2.
The demand sensor R2.2 is connected to the terminals X3/
GND and n1/J2-U2.
10) The external sensor (R1) is connected to terminals X3/GND
(ground) and N1/J2-U1.
11) The domestic hot water sensor (R3) is installed in the
domestic hot water cylinder and is connected to terminals
X3/GND (Ground) and N1/J2-U3.
When using three-phase current pumps, a power contactor can be
activated with the 230 V output signal of the heat pump manager.
Sensor cables can be extended to up to 50 m in accordance with the
dimensioning parameters.
Further information on the wiring of the heat pump manager is available
in the electrical documentation.
The communication cable is necessary for the function of air-to-water
heat pumps in outdoor installation. It must be shielded and laid
separately from the mains cables. It is connected to n1-J25. For further
information, see electrical documentation
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dimplex WPM Econ5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dimplex WPM Econ5 in de taal/talen: Duits, Engels, Frans als bijlage per email.

De handleiding is 1.81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info