Handleiding Dimplex MK1 (pagina 2 van 12) (Nederlands, Duits, Engels, Frans)

798053

Verklein

Vergroot

Pagina terug

1/12

Pagina verder

93mm

305mm

Energy Related Product Directive

Type of heat output/ room temperature control

With electronic room temperature control Yes

Electronic room temperature control plus week

timer Yes

With open window detection Yes

Model Identiﬁer(s):

B075E C100E D150E E200E

Nominal heat

output Pnom 0.75 kW 1 kW 1.25 kW 1.5 kW

Height (mm)

659 659 659 659

Width (mm)

570 840 1105 1373

Depth (mm)

50 50 50 50

Minimum heat

output (indicative) Pmin 0.75 kW 1.00 kW 1.25 kW 1.5 kW

Maximum continu-

ous heat output Pmax,c 0.75 kW 1.00 kW 1.25 kW 1.5 kW

Auxiliary electricity Consumption

At nominal heat

output elmax 0.00 0.00 0.00 0.00

At minimum heat

output elmin 0.00 0.00 0.00 0.00

In standby mode elSB <0.0005 <0.0005 <0.0005 <0.0005

With open window detection Yes

This product complies with Lot20 of the Energy Eciency Directive (2015/1188)

General Information

Please read the instructions closely before ﬁrst using the product.

The necessary wall mounting brackets are provided with the product as a

standard.

It should only be operated when in the upright position as shown - see Fig.1.

All models are IP20 rated. Before connecting the heater check that the supply

voltage is the same as that stated on the heater.

For further information on heater guards, please contact our guard supplier

direct on Tel. No. 020 7987 1184 or visit www.aianos.co.uk, or in case of diculty

or for further advice contact the Customer Helpline.

Wall Mounting

IMPORTANT - The radiator must only be mounted using the kit supplied

WARNING - This product is heavy and care should be taken in installation

Select a suitable position on a wall, near to a mains power outlet. The radiator

should not be mounted closer than 75mm from the ﬂoor - see Fig. 2 (to enable

cleaning), or adjacent side walls. Ensure at least 305mm clear space between

the radiator and any overhanging shelf. It should not be mounted closer than 1

metre from the ceiling.

STEP 1: Check that you have all the necessary components:

(a) 2 x Bottom wall brackets

(b) 2 x Top wall brackets

(d) 2 x Self-tapping screws.

STEP 2: Using a straight edge, draw a horizontal line (see ‘Y’ in Fig. 2) for the

bottom brackets at the required mounting height from the ﬂoor.

75mm

(min)

‘C’

‘Y’

75mm

(min)

Fig. 2

Fig. 3

Fig. 4 Fig. 5

Electrical Connection

Place the bottom brackets centrally over these centres with the top row of holes

on the line, and mark the ﬁxing hole positions – see Fig. 2.

STEP 3: Drill the holes and ﬁt wall plugs. Screw the bottom brackets in position

– see Fig. 2.

STEP 4: Measure dimension D in Fig. 1 according to model, from the top of the

bottom brackets and draw a horizontal line. Mark o the ﬁxing centres for the

top brackets in line with the bottom brackets. Place each top bracket on the

line and mark the ﬁxing holes – see Fig. 3. Drill and plug the wall and ﬁx the

top brackets in place.

STEP 5: Place the radiator on the bottom brackets, then ﬁt each securing

bracket to the top of the radiator and secure it with the self-tapping screw

provided – see Fig. 4.

Check that the radiator is securely ﬁxed to the wall.

This guide is for quick reference only

To view the full manual, please visit - www.dimplex.nl

NOTE - The bottom of the radiator must not be less than 75mm from the

ﬂoor. To achieve this the top edge of the bottom brackets must be at least

160mm from the ﬂoor - see Fig 2. On this line, mark o the ﬁxing centres

according to model - see `C’ in the table in Fig. 1 and Fig. 2

IMPORTANT - For safe clearances from shelf/obstacle - see Fig. 5

(max)

(min)

The electrical installation must be carried out by a competent electrician,

and be in strictaccordance with the current I.E.E. Regulations for Electrical

Equipment in Buildings. The wires in this mains lead are coloured in accordance

with the following code:

GREEN AND YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

The heater is ﬁtted with a length of ﬂexible cable type H05VV-F size 3 x

1.0mm2 for connection to the ﬁxed wiring of the premises through a suitable

connection box positioned adjacent to the heater.

A means for disconnection must be incorporated in the ﬁxed wiring of the

premises in accordance with the wiring rules. The supply circuit to the heater

must incorporate a double pole isolating switch having a contact separation

of at least 3mm.

WARNING - THIS APPLIANCE MUST BE EARTHED

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Dimplex MK1 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info