706555
8
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
- 2 -
Installation Instructions
Before installing this appliance, we recommend that;
1. You have your chimney cleaned by a competent
chimney sweep.
2. You block o the chimney  ue.
This procedure is important for the e cient operation
of the heating unit and will also reduce heat loss up the
chimney.
Installation.
Ensure that all packing items are removed (read any
warning labels carefully).
Retain all packing for possible future use, in the event
of moving or returning the appliance to your supplier.
To install the appliance;
1. Remove the  replace grate, ashpan etc.
2. The ashbed grate should be stored away for possible
future use.
3. Clean the hearth of any ash residue or dust etc.
At the rear of the appliance, two adjustable supports are
provided for levelling, where the base of the  replace
opening is raised above the level of the hearth.
You are now ready to install the electric  re into your
replace.
Make sure the unit is switched OFF.
Hold the  re by the sides of surround and gently
manoeuvre into position. Plug the  re into a 13amp/240
volt outlet. Ensure that the supply cable exits at the front
of the  re, at the right or left hand corner to suit your
supply socket location and is not trapped under the  re
such that it might cause it to be damaged.
Before using the manual controls  rstly ll the water
tank (See ‘Maintenance’, ‘Filling the water tank’).
Manual Controls.
The Opti-myst Manual controls are located beneath the
hinged canopy cover. Raise the canopy cover to access the
controls. (See Fig. 2 for Manual Control lay out)
Switch A’:- Controls the electricity supply to the heater.
Note: This switch must be in the ON’ ( I ) position for the
heater to operate with or without heat.
Switch ‘B’:- Controls the function of the  re.
Press
once to turn on  ame e ect. This will be
indicated by one beep.
Although the main lights operate immediately it will
take a further 30 seconds before the  ame e ect starts.
Press again to give  ame e ect and half heat.
This will be indicated by two beeps.
Press
again to give  ame e ect and full heat. This
will be indicated by three beeps.
Press
again to return to  ame e ect only.
This will be indicated by one beep.
Press to put  re in to standby mode.
This will be indicated by one beep.
Control Knob ‘C’:- Controls the intensity of the  ame
e ect.
Turning the control knob Clockwise increases the  ame
e ect, turning the control knob Anti Clockwise will
decrease the  ame e ect.
Control Knob ‘D’:- Controls the Electronic Thermostat
setting.
Turning the control knob Clockwise will decrease the
temperature setting, turning the control knob Anti
Clockwise will increase the temperature setting.
When the water is empty the main lamps go out. See
instructions under ‘Maintenance, ‘Filling the water tank’.
When this procedure is complete, the main lamps will
illuminate but it will take 30 seconds before the  ames
return.
Electronic Thermostat
The thermostat controls the heat output according to
the room temperature. This ensures that the heater
will not produce heat unnecessarily when the room is
warm.
To set the temperature you require, turn the thermostat
control knob ‘D’ (See Fig. 2) Anti-Clockwise until the
desired temperature is reached. Alternatively to heat
a cold room quickly, turn the thermostat control knob
‘D’ (See  g. 2) up fully. When the room has reached the
desired temperature, turn the thermostat control knob
‘D’ (See Fig. 2) clockwise until the desired heat setting is
achieved.
The heater will now automatically operate at this
temperature.
Remote Control Operation
On the control panel, Switch A (see Fig. 2) must be in the
‘ON ( I ) position in order for the remote control to operate.
There are 3 buttons on the remote control. (See Fig. 7)
To operate correctly the remote must be pointed towards
the front fuel e ect.
The remote control functions are as follows:
Press once to turn on Flame e ect only.
This will be indicated by one beep.
Press once to turn on Half heat and Flame e ect.
This will be indicated by two beeps.
Press again to turn on Full heat and Flame e ect.
This will be indicated by three beeps.
Standby
This will be indicated by one beep.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dimplex Hemmet bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dimplex Hemmet in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 4,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info