798061
9
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
To access the electrical connections hub:
• Remove the cover and the shell.
Remove the cover of the appliance by removing the screws which
x the shell onto the lower part of the appliance.
Remove the black protective cover from the electronics board.
The power supply should comply with all regulations in eect in
the country of installation, as well as the NFC 15-100 standard.
A method of disconnection which ensures total power-cut in
Category III conditions should be installed in xed piping in
compliance with the installation rules.
• an 8A all-pole circuit breaker with a minimum 3mm
contact opening.
• a protective 8A circuit breaker with a 30mA dierential.
If the power supply cable is damaged it must be replaced by the
manufacturer, their customer service technicians, or by a qualied
technician to avoid any risk of injury or danger.
4.5 - Electrical connections
4.5.1 - External control
Only a dry contact, voltage-free, external
connection may be used. Otherwise you
risk damage to the electronics board.
Do not connect the heat pump water
heater to wiring from an older water
heater using the peak/o-peak hours contact.
The heat pump water heater must always be
connected to a power supply.
Peak/o-peak control can be managed through
programming or though an independent cable.
Grounding is obligatory.
Power supply is managed through a 230V single-
phase and grounding cable.
The heat pump water heater can be used to continuously
ventilate a room even if the heating cycle is complete.
To stop the fan from operating, connect a timer on a moisture
sensor. Use the same procedure as for the timer switch, but
connect the 2-wire cable to «Input 2» on the electronics board.
- Switch open = the fan will not operate
- Switch closed = the fan will operate
• Set the regulator to «External control ventilation mode» : fan
mode 3.
4.5.1.2 - Controlled ventilation
4.5.1.1 - Peak/o-peak hours contact
To prevent the electrical back-up from running during peak
hours, connect the dry contact originating from the electricity
counter, to terminal 1.
- Switch open = Back-up not allowed to run
- Switch closed = Back-up allowed to run
By choosing load shedding level 0 or 1 (see § «Load shedding»),
you stop the electrical back-up alone from running (load
shedding =1) or the heat pump and the electrical back-up from
running (load shedding = 0).
• Pass a 0,75mm² 2-wire cable with metal tips through a cable
gland at the back of the appliance and bring the end of the
cable around to the electronics board. The other end of the cable
should be connected to the timer switch.
• Insert the 2-wire cable through a grommet from the electronics
box.
• Connect the 2-wire cable to «Input 1» indicated on the electonics
board, having already removed the existing red bridge.
4.5.1.3 - Electricity provider contact
To program the operation of the heat pump water heater during
peak/o-peak hours, it is not necessary to connect the dry contact
to the electricity counter.
It is possible to program scheduled operating times for the heat
pump water heater or of the electrical back-up from the control
panel (see §3.8 Programming).
It is possible to connect the dry contact from the electricity
counter to the heat pump water heater without programming
from the control panel.
- Switch open = Load shedding
- Switch closed = Normal functioning
The level of load shedding can be chosen from the control panel
of the appliance (see § 5.9.2.4 Load shedding).
By default the electrical resistance does not operate during peak
hours. .
It is not advised to operate the heat
pump water heater during o-peak hours
so as to optimise its functionality.
- INSTALLER HEAT PUMP WATER HEATER 200 -270L AIR D/2 - MANUAL - 9
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dimplex Edel 200 AIR D-2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dimplex Edel 200 AIR D-2 in de taal/talen: Engels als bijlage per email.

De handleiding is 2.49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Dimplex Edel 200 AIR D-2

Dimplex Edel 200 AIR D-2 Gebruiksaanwijzing - Nederlands - 48 pagina's

Dimplex Edel 200 AIR D-2 Installatiehandleiding - Nederlands - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info