695348
41
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
English
INSTALLATION MANUAL
When replacing the cord proceed as follows:
Ø
Open the door.
Ø
Remove the cord and the mastic from the recess.
Ø
Apply a new layer of heat resistant mastic in the recess where the cord was.
Ø
Place a new cord in the recess. Do this loosely and do not pull the cord tight.
Ø
Insert both ends of the cord in the special sleeve.
The cord, the sleeve and the mastic are available through your supplier.
!Caution
Make sure that the sleeve is placed on the underside of the glass pane.
The door can also be adjusted in height. There are 2 eyelets on the upper pin on which the door is hung.
Removing 1 or more of these eyelets allows the door to fall to the desired level.
Proceed as follows when adjusting the door handle:
Ø
Loosen the 2 hexagonal pin nuts around which the handle of the door falls a few turns (see Appendix 2, fig. 8a
(Instyle and Prostyle 700) and 8b (Instyle and Prostyle 700). This pin ensures that the door is tightly clamped.
Ø
Adjust the pin.
Ø
Tighten the 2 hexagonal nuts again.
Ø
Test the sealing of the door (see the start of this paragraph).
Ø
Repeat this process if the result is not satisfactory.
9.4 Glass pane(s)
!Caution
Avoid damage when removing/fitting the glass pane(s);
Avoid/remove fingerprints on the glass pane(s) because these burn in.
Tip!
Use the supplied pane window cleaner to remove fingerprints/dirt on the glass pane(s).
9.4.1 Disassembly of glass pane in door(s)
To remove the glass pane in the door(s) follow the instructions below:
(For a Prostyle appliance: see Appendix 2, fig. 9. For an Instyle applianc: see Appendix 2, fig. 10).
!Caution
When you install an Instyle or Prostyle Tunnel: Follow the instructions below. Then repeat these instructions on
the other side of the appliance.
Ø
Open the door.
Ø
Lift the door out by first sliding it upwards, then tilt it slightly forwards and allow it to lower.
Ø
Place the door on a flat surface.
Ø
Remove the nuts from the strips.
Ø
Remove the strips.
Ø
Lift the glass pane out. The pane seal is then also taken out.
Tip!
When replacing the glass pane always replace the seal in the door (= seal between the glass pane and the
door).
Check the door sealing cord and replace if necessary (see paragraph 9.3).
9.4.2 Assembly of glass pane in door(s)
Assemble the glass panes in the door(s) according to the steps described in paragraph 9.4.1 ‘Disassembly of glass
pane in door(s)’ but in reverse order.
(For a Prostyle appliance: see Appendix 2, fig. 9. For an Instyle appliance: see Appendix 2, fig. 10).
!Caution
Assembly of the door(s) is somewhat different.
Proceed as for assembly of the door(s):
Ø
Bring the hole at the bottom of the hinging part of the door exactly below the lower pin.
Ø
Slide the door up. The pin slides into the lower hole.
Ø
Bring the hole at the top of the hinging part of the door exactly above the upper pin and allow the door to lower.
The pin slides into the upper hole.
Ø
The door is now assembled.
!Caution
Do not fasten the bolts too tight to avoid breaking off and/or stripping: overtightening will cause breakage.
Place the glass pane (including new pane seal) with the logo to the bottom right.
41
41

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dik Geurts Prostyle 800V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dik Geurts Prostyle 800V in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 3.54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Dik Geurts Prostyle 800V

Dik Geurts Prostyle 800V Gebruiksaanwijzing - Nederlands, Deutsch, English, Français - 64 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info