695348
35
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
English
INSTALLATION MANUAL
5.7.1 Free-standing/design fires
5.7.1.1 Conversion from fire top connection to rear connection (if applicable).
The fire is supplied with a top connection for connecting the flue duct.
The top connection can be converted to a rear connection.
To do this proceed as follows (see Annex 2, Fig. 2):
Ø
Take the flame baffle plate or baffle plates out of the fireplace (if applicable see section 9, 'Appliance-specific
information').
Ø
Your appliance can be provided with an extra steel restrictor cap (if applicable see section 9, 'Appliance-specific
information'). Remove this by sliding the restrictor cap forwards and taking it out of the rails. This restrictor cap is
not replaced with a rear connection.
Ø
Remove the fire's convection back plate by undoing the bolts.
Ø
Remove the push-through plate from the convection back plate.
Ø
Remove the cover plate for the flue from the back wall of the fire by undoing the 2 or 3 nuts.
Ø
Remove the flue ring from the top plate by undoing the nuts and/or bolts.
Ø
Fit the flue ring on the back wall using the bolts and/or nuts.
Ø
Fasten the convection back plate again with the bolts.
Ø
Assemble the cover plate for the flue in the opening in the top plate using the nuts.
Ø
Replace the flame baffle plate or baffle plates in the reverse order.
5.7.1.2 Installing a free-standing fire, general
A free-standing fire is installed as follows:
Ø
Determine the fire location. The dimensions of the appliance are given in Annex 1, Table 2.
Ø
For any appliance-specific instructions we refer to section 9 'Appliance-specific information'.
Ø
Make sure there are no combustible materials present.
Ø
Lay the floor plate if applicable.
Ø
Place the fire on a blanket or sheet of cardboard (to avoid damaging the floor) then put it in the desired place.
Ø
Connect the fire to the flue duct. Follow the instructions of the supplier of the flue gas extraction system. Use
heater piping material that at least suffices with regard to EN 1856-2 T600.
Ø
Lift the fire a little if necessary so the blanket or cardboard can be removed.
Ø
For completing installation we refer to paragraph 5.8.
5.7.1.3 Design fire installation
To install a design fire we refer to Section 9 'Appliance-specific information'.
5.7.2 Insert fires (existing and new situation)
5.7.2.1 With an existing chimney or chimney breast
To install an insert fire with an existing chimney or chimney breast proceed as follows:
Ø
Determine the fire location. The dimensions of the appliance are given in Annex 1, Table 2.
Ø
Leave a space of at least 10 mm between the fire and construction materials.
Ø
Check the size of the recess. If necessary the walls of the open hearth can be broken out a little. Make sure that the
chimney top is still sufficiently supported.
Ø
If applicable make room for the connection of the convection openings (if applicable see section 9
'Appliance-specific information') and section 5.3 'Convection')) with a flexible aluminium pipe and ventilation
elements (see section 5.4 'Appliances with fan(s)'. These accessories can be ordered from your supplier.
Ø
Be careful with the chimney breast plaster. Plaster beading makes the recess smaller.
Ø
Remove any existing valve from the open hearth or slide and clean the chimney top so all soot is removed.
Ø
Remove the fire door and disassemble the frame when it is supplied separately (see section 9 'Appliance-specific
information').
Ø
Carefully remove the inner lining plates (mark them), the baffle plate and (if present) the restrictor cap from the
fire (if applicable see, section 9 'Appliance-specific information').
Ø
Lay any bottom plate supplied where the fire is to be installed.
Ø
Turn the adjustable legs in with the hexagonal socket screwdriver supplied and check whether they are properly
adjustable. There may still be some blasting grit present.
Ø
Make sure there is sufficient room under fire for the supply of combustion air when there is no outside air
connection.
Ø
An outside air connection can be made (if applicable see section 9 'Appliance-specific information').
35
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Dik Geurts Prostyle 800V bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Dik Geurts Prostyle 800V in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 3.54 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Dik Geurts Prostyle 800V

Dik Geurts Prostyle 800V Gebruiksaanwijzing - Nederlands, Deutsch, English, Français - 64 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info