499284

Digitalbox IMPERIAL DB 2 Handleiding

46
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
DigitalBox Europe GmbH
Sandstraße 65 · D-40878 Ratingen
BDA Imperial DB 2_GB_TO.indd 48BDA Imperial DB 2_GB_TO.indd 48 15.10.2008 13:47:05 Uhr15.10.2008 13:47:05 Uhr
47 DVB-S Receiver
GB
7. TECHNICAL SPECIFICATION
VIDEO
Decoding . . . . . . . . . . . . . . . . . . . . . . . .MPEG-2 & MEPG-1 compatible
Bit rate . . . . . . . . . . . . . . . . . . . . . . . . . .Max 15Mbps
Output . . . . . . . . . . . . . . . . . . . . . . . . . .PAL/NTSC
Aspect ratio. . . . . . . . . . . . . . . . . . . . . .4:3, 16:9, Auto
Active pixel . . . . . . . . . . . . . . . . . . . . . . .720x480 @ 30fps; 720x576 @ 25fps
Output connector . . . . . . . . . . . . . . . . .RCA, TV SCART
AUDIO
Decoding . . . . . . . . . . . . . . . . . . . . . . . .MPEG-2/MPEG-1 layer I & II
Mode . . . . . . . . . . . . . . . . . . . . . . . . . .Mono, Dual, Stereo, Joint stereo
Bit rate . . . . . . . . . . . . . . . . . . . . . . . . . .Max 384Kbps
DEMODULATOR
Demodulation . . . . . . . . . . . . . . . . . . . .QPSK
Symbol rate . . . . . . . . . . . . . . . . . . . . . .SCPC/MCPC
Outer code. . . . . . . . . . . . . . . . . . . . . . .RS (204, 188, 8)
Inner code . . . . . . . . . . . . . . . . . . . . . . .ALL DVB rates
Energy dispersion. . . . . . . . . . . . . . . . .DVB-S recommendation
INPUT SIGNAL
Frequency. . . . . . . . . . . . . . . . . . . . . . . .950MHz
~
2150MHz
Input level . . . . . . . . . . . . . . . . . . . . . . . .-65dBm
~
-25dBm
Channel bandwidth. . . . . . . . . . . . . . . .36MHz
Input socked . . . . . . . . . . . . . . . . . . . . .F-type connector
LNB CONTROL
Power supply . . . . . . . . . . . . . . . . . . . . .13/18V (500mA max) with short circuit protection
Polarized control. . . . . . . . . . . . . . . . . .13/18V polarization (vertical/horizontal)
DiSEqC control . . . . . . . . . . . . . . . . . . .DiSEqC1.0, DiSEqC1.1 and DiSEqC1.2
RF MODULATOR
Input . . . . . . . . . . . . . . . . . . . . . . . . . .IEC 169-24 Male x 1
Output . . . . . . . . . . . . . . . . . . . . . . . . . .IEC 169-24 Female x 1
Band . . . . . . . . . . . . . . . . . . . . . . . . . .UHF
TV Standard . . . . . . . . . . . . . . . . . . . . .PAL BG/I/DK, NTSC M
Output Channel . . . . . . . . . . . . . . . . . . .21
~
69(PAL), 14
~
83(NTSC)
BDA Imperial DB 2_GB_TO.indd 47BDA Imperial DB 2_GB_TO.indd 47 15.10.2008 13:47:06 Uhr15.10.2008 13:47:06 Uhr
46Installation Guide
GB
6.5.2 Upgrade by Satellite
This function can upgrade the software of
your receiver through data sent by a satellite.
At the moment we offer satellite updates
only through ASTRA1 and Hotbird satellites.
1. Select the satellite and TP or input the TP
value and download PID.
2. Then mark “Start” and press [Enter] to
begin the download of the upgrade.
This may need up to 60 minutes. Therefore we suggest using of this function only if
you don’t intent to watch TV during this time.
6.6 SatcoDX Auto Programming
This function is using the tables of the SatcoDX websites to update your channel and
satellite lists. You need a special application which is available on the CD-ROM of the
Tele-Satellite magazine. Install this software on your PC fi rst.
1. Start the SatcoDX application on your PC.
2. Select “SatcoDX Auto Programming” item from the “Tools” menu and press [OK].
The screen will show the message “OK to Proceed”.
3. Press [OK] again and you will see the message “Ready to Download”.
4. In the PC application set the Baud Rate to 115200 and start the download procedure.
! Caution:
The new download channels will delete the original channels list. Please be careful
before using it.
6. TOOLS
BDA Imperial DB 2_GB_TO.indd 46BDA Imperial DB 2_GB_TO.indd 46 15.10.2008 13:47:06 Uhr15.10.2008 13:47:06 Uhr
45 DVB-S Receiver
GB
6.5 Software Upgrade
When you enter to “Software Upgrade”
menu, you will see a screen like beside:
1. Press [CH
] to select the wanted
item among Software Upgrade and
Upgrade by Satellite.
2. Press [OK] to enter the selected item.
6.5.1 Software Upgrade
1. This function allows you to upgrade the
software of the receiver. This can be done
from PC to receiver or from a master
receiver to a slave receiver.
2. Connect master receiver or PC to the
slave receiver via serial interface
(0-Modem cable). Enter the “Software
Upgrade” menu of the master receiver
and press [Vol ], to change the upgrade
mode. Upgrade modes include: All code/
Main code/CAS-data/Script GUI/Radio Back/default DB/Userdb.
3. Switch on the slave receiver.
4. Mark “Start” on the master reeciver and press [OK] to start upgrade.
Wait until the display on the front panel shows “-END”. Then switch off the receiver
and on again. Now the new software is used.
5. Press [MENU] to save the setting without upgrade.
6. TOOLS
BDA Imperial DB 2_GB_TO.indd 45BDA Imperial DB 2_GB_TO.indd 45 15.10.2008 13:47:07 Uhr15.10.2008 13:47:07 Uhr
44Installation Guide
GB
3. Othello
• Mark “Setup” and press [Vol
] to select
the game level (degree of diffi culty).
• Mark “Start” and press [OK] to start the
game.
• Mark “Cancel” and press [OK] to leave the
game.
• Play the game:
• Press [Vol /CH ] to position the
round mark.
• Press [OK] to set your stone.
• Press [Exit] to quit the game and return to the game menu.
6.4 Factory Default
When you press [OK] on the “Factory
Default” item:
1. A dialogue box will occur where you need
to enter the password.
2. After you input the correct password a
warning message will be displayed like the
one beside.
3. If you select “Yes” then all changes you
made will be reset to default values. Make sure you really want to do this!
4. Press [Exit] in both steps will close the window without resetting the receiver.
6. TOOLS
BDA Imperial DB 2_GB_TO.indd 44BDA Imperial DB 2_GB_TO.indd 44 15.10.2008 13:47:08 Uhr15.10.2008 13:47:08 Uhr
43 DVB-S Receiver
GB
Basic operation statement:
1. Tetris
• Mark “Setup” and press [Vol
] to
select the level (speed).
• Mark “Start” and press [OK] to start
the game.
• Mark “Cancel” and press [OK] to leave
the game.
• Play the game:
• Press [Vol ] to move the block left
or right
• Press [Channel ] to rotate the block clockwise
• Press [Channel ] to drop the block faster
• Press [OK] to Pause/Play the game
• Press [Exit] to leave the game and return to the game menu.
2. Snake
• Mark “Setup” and press [Vol ] to
select the level (speed).
• Mark “Start” and press [OK] to start
the game.
• Mark “Cancel” and press [OK] to leave
the game.
• Play the game:
• Press [Vol /CH ] to guide the
snake to the red blocks. Every block
you ate increases the length of the snake. If the snake runs against a wall or
against itself then it dies.
• Press [OK] to Pause/Play the game
• Press [Exit] to quit the game and return to the game menu.
6. TOOLS
BDA Imperial DB 2_GB_TO.indd 43BDA Imperial DB 2_GB_TO.indd 43 15.10.2008 13:47:09 Uhr15.10.2008 13:47:09 Uhr
42Installation Guide
GB
6. TOOLS
When you enter to “Tools” menu, you will see
a screen like beside:
In “Tools” menu:
1. Press [CH ] to select the wanted
item among Information, Quick Setup,
Game, Factory Default, Software Upgrade,
SatcoDX Auto Programming
2. Press [OK] to enter the selected item.
6.1 Information
1. When you select the “Information” menu
you will see a screen like beside. The
screen displays data about the current
channel.
2. Press [Exit] button to leave the informa-
tion display.
6.2 Quick Setup
When the STB is used, which need to repeat
set menu Language, First Audio, Second
Audio, LNB Power, Single Search and Multi
Search.
6.3 Game
When you enter “Game” menu, you will
see three games include Tetris, Snake and
Othello.
BDA Imperial DB 2_GB_TO.indd 42BDA Imperial DB 2_GB_TO.indd 42 15.10.2008 13:47:10 Uhr15.10.2008 13:47:10 Uhr
41 DVB-S Receiver
GB
5.6 Power setting
• Here you can set the power output to
the LNB. If your receiver is connected
to the LNB directly then you need to set
the LNB
Power to “On”. If your receiver is
connected
to a multi switch (SMATV signal
distribution system) then it may be that
you don’t need to provide the power to the
LNB. But since this is depending on the
kind of installed distribution system we
recommend you to contact your installer or to refer to the user manual of this system
to get the correct information.
• You also just can change this setting and check if you still can receive the channels.
If the LNB Power is off and you still can see all channels then we recommend this
setting in order to save energy.
5.7 RCU Position Switch
When many receivers are working at the
same time, In order to prevent the other
receivers to be disturbed when operating
the current receiver, here you can switch
RCU position, it has three items: Position 1,
Position 2 and Position 3, default position is
Position 1.
5. SYSTEM SETUP
BDA Imperial DB 2_GB_TO.indd 41BDA Imperial DB 2_GB_TO.indd 41 15.10.2008 13:47:11 Uhr15.10.2008 13:47:11 Uhr
40Installation Guide
GB
5. SYSTEM SETUP
5.5 Parental Lock
You can set a password for anyone who
wishes to operate the “Installation” menu.
You can also set the password to lock chan-
nels. Below you fi nd how to set and change
the password.
1. On “Parental Lock” press [OK] to open
a dialogue box and input the password.
After you entered the correct password,
you will see a screen like beside:
2. Menu Lock: If Menu Lock is set to “Yes” then you need to enter the password every
time you want to open the menu. If set to “No” then you can open the menu without
entering the password fi rst.
3. Channel Lock: If set to “Yes” then you need to enter the password before you can see
those channels which have been marked as locked channels in the channel menu. If
set to “No” then even those channels can be selected without entering the password
fi r s t .
4. New Password: Here you can change the existing password. You should do this
after you set up the receiver the fi rst time and every time when you think that your
password is known by unauthorized persons. To change the password enter the new
password in the “New Password” item and repeat the same one in the “Confi rm Pass-
word” item. If the passwords are not identically then you will see a warning message.
If you entered the same new password in both fi elds then you will see the message
“Saving Data, Please Wait…”. From now on you need to use the new password to
open locked menus or locked channels.
Note: The default password is 0000.
5. Press [Exit] to leave the “Parental Lock” menu.
BDA Imperial DB 2_GB_TO.indd 40BDA Imperial DB 2_GB_TO.indd 40 15.10.2008 13:47:12 Uhr15.10.2008 13:47:12 Uhr
39 DVB-S Receiver
GB
5. SYSTEM SETUP
5.4 OSD Setting
When you select “OSD Setting” you will see a
screen like beside:
1. Subtitle Display: Press [Vol
] to select
“Off”, “Standard” or “Teletext Subtitle”. If
the current channel has subtitle informa-
tion, it will be displayed if this function is
“Standard” or “Teletext Subtitle”. If this
function is “Off” subtitles won’t be dis-
played.
2. OSD Timeout: This setting determines the duration the info window is displayed on
the screen when you change channels. Press [Vol
], to set the time between 1 to
10 seconds.
3. Position: Press [Vol ] select the position between top and bottom.
4. OSD Transparency: With this parameter you can set the transparency of the menus.
Press [Vol ] select the value between 10%, 20%, 30%, 40% and “Off” (means no
transparency function).
5. Load OSD Setting Default: If you want to reset your OSD settings to the default
settings then select this item and press [OK].
6. Press [Exit] button to leave the “OSD Setting” menu.
BDA Imperial DB 2_GB_TO.indd 39BDA Imperial DB 2_GB_TO.indd 39 15.10.2008 13:47:12 Uhr15.10.2008 13:47:12 Uhr
38Installation Guide
GB
5. SYSTEM SETUP
2. Local Time Setting: When you select
“Local Time Setting” and press [OK] then
you will see a window like the one beside:
• GMT Usage: This item is used to set
the time by using the time signal from
the satellite. Press [Vol ] to change
the setting.
• The “GMT Offset” item is only available
when “GMT Usage” is set to “On”.
Press [Vol
] to set the “GMT Offset” value. With every time you press the button
the time offset will be increased/decreased by half an hour.
• Summer: Press [Vol ] to switch this function “On” or “Off”.
• “Date” and “Time” items are only available when the “GMT Usage” is set to “Off”.
Press [Vol ] to select one item and use number buttons to input time and date
directly.
• Time Display: Press [Vol ] to switch this function “On” or “Off”.
Note: If the current channel provides the correct time information, you will see the
current time after you entered “Local Time Setting” menu. If the channel doesn’t
provide time information, you have to input the date and time information manually.
The most channels support the time signal.
• Press [Exit] to leave the “Time” menu.
3. Sleep Timer: Select “Sleep Timer” item and press [OK] to set the sleep timer. You will
see “Sleep timer OFF/Sleep timer 10/Sleep timer 30/Sleep timer 60/
Sleep timer 90/Sleep timer 120”.
If you set a sleep time, the system will change to standby mode after the chosen time
period.
BDA Imperial DB 2_GB_TO.indd 38BDA Imperial DB 2_GB_TO.indd 38 15.10.2008 13:47:13 Uhr15.10.2008 13:47:13 Uhr
37 DVB-S Receiver
GB
5. SYSTEM SETUP
• When you select “Message” (reminding message) option in “Timer Service” then
you can enter additional data:
• Wakeup Message: Press [Vol
] to select the category
• of the wakeup message from Birthday, Anniversary and General.
• Wakeup Date: Use the [Number] buttons to input your wakeup date.
• On Time: Use the [Number] buttons to input your wakeup time. If date and time
are reached, no matter if the system is in standby mode or in playing mode, it
will automatically show a reminding message. The message will be displayed on
the screen until you press [Exit] to close it.
• Duration: Here you can set the time you want to see or play this channel. After
the time set the system will automatically switch to standby mode. If you don’t
want the box the be switched to standby mode then set the duration to 00:00.
• Press [Exit] to leave the “Timer” menu.
BDA Imperial DB 2_GB_TO.indd 37BDA Imperial DB 2_GB_TO.indd 37 15.10.2008 13:47:14 Uhr15.10.2008 13:47:14 Uhr
36Installation Guide
GB
5. SYSTEM SETUP
5.3 Time & Timer Setting
When you enter “Time & Timer Setting” a menu with this 3 items will be opened.
1. Timer: Select “Timer” item and press [OK]
to enter the “Timer” menu.
You can press [CH ] to select item.
• The current time will be displayed in
the fi rst column. If the current time
is incorrect, please modify it with the
[Number] buttons.
• Timer Number: You can press
[Vol
] to switch the timer number.
There are totally 8 timers.
• Timer Mode: Select how often the timer is running: Once, Daily, Weekly, Monthly
and Yearly, or switch the timer to off.
• Timer Service: Select between TV Channel, Radio Channel and Message.
• When you select “TV Channel/Radio
Channel” (timer setting for channel
change and Wakeup channel/date)
then you have further options you need
to set:
• Wakeup Channel: Press [OK] to
enter the channel list, and select the
channel you want to see with
[CH ], press [OK] to confi rm it.
• Wakeup Date: Use number buttons to input your wakeup date.
• On Time: Use number buttons to input your wakeup time. If date and time are
reached then no matter if the system is in standby mode or in playing mode, it
will automatically switch to the channel you set and start to play.
• Duration: Here you can set the time you want to see or play this channel. After
the time set the system will automatically switch to standby mode. If you don’t
want the box the be switched to standby mode then set the duration to 00:00.
BDA Imperial DB 2_GB_TO.indd 36BDA Imperial DB 2_GB_TO.indd 36 15.10.2008 13:47:14 Uhr15.10.2008 13:47:14 Uhr
35 DVB-S Receiver
GB
4. Subtitle Language: In “OSD Setting”menu, use [Vol ] to select “On” or “Off”. If the
current channel has subtitle information, it will be displayed if this function is “On”. If
this function is “Off” subtitles won’t be displayed. The selections of subtitle language
include: English, German, French, Spanish, Italian, Portuguese, Turkish, Polish,
Russian, Danish, Greek, Hungarian, Arabic and Farsi.
5. Teletext: Press [Text] button in TV mode to open the teletext page. This service is
depending on the support of the channel provider. If the channel does not support
teletext information, it will show “No Teletext Data” on the screen. The selections of
teletext language include: English, German, French, Spanish, Italian, Portuguese,
Turkish, Polish, Russian, Danish, Greek, Hungarian, Arabic and Farsi.
6. Press [Menu/Exit] to return back from “Language” menu.
5.2 TV System
When you enter the “TV System” menu you
will see the screen like below:
1. Display Mode is used to switch the display
mode. You can select from Auto/PAL/
PAL-M/PAL-N/NTSC3.58/NTSC4.43.
Press [Vol ] to switch the desired mode.
2. Aspect Mode is used to switch the screen aspect ratio mode. You can select the
needed mode from Auto/4:3 PS/4:3 LB/16:9 with [Vol ].
3. Video output is use for switching the screen aspect ratio mode. Now we provide
below options: CVBS/CVBS + RGB/CVBS + S-Video. You can press [Vol ] key to
select each mode circularly.
5. SYSTEM SETUP
BDA Imperial DB 2_GB_TO.indd 35BDA Imperial DB 2_GB_TO.indd 35 15.10.2008 13:47:15 Uhr15.10.2008 13:47:15 Uhr
34Installation Guide
GB
5. SYSTEM SETUP
When you open the “System Setup” menu a
window like the one beside will be opened.
In “System Setup” menu:
1. Press [CH ] to select menu items
among Language, TV System, Time &
Timer setting, OSD Setting, Parental Lock
and Power setting.
2. Press [OK] to open the selected item.
5.1 Language
After selecting the “Language” menu you will
see a window like beside:
1. Menu Language: Press [Vol ] to select
languages. The selection of language
include: English, German, French, Spanish,
Italian, Portuguese, Turkish, Polish, Rus-
sian, Danish, Greek, Hungarian, Arabic
and Farsi.
2. First Audio: Some channels offer more than one audio language. This function
allows you to set the preferred audio language for those channels. If a channel offers
the same audio language as the “First Audio” you set the system will play this audio
language as default. If the channel does not offer this audio language then the system
will compare the offered languages with the second audio language. The selections of
audio language include: English, German, French, Spanish, Italian, Portuguese, Turkish,
Polish, Russian, Danish, Greek, Hungarian, Arabic and Farsi.
3. Second Audio: If the channel has no audio language that corresponds with “First
Audio” but with “Second Audio” the system will play the second audio language as
default. If no audio language corresponds with the “Second Audio” then the default
language of the current channel will be played instead. The selections of audio
language include: English, German, French, Spanish, Italian, Portuguese, Turkish,
Polish, Russian, Danish, Greek, Hungarian, Arabic and Farsi.
BDA Imperial DB 2_GB_TO.indd 34BDA Imperial DB 2_GB_TO.indd 34 15.10.2008 13:47:16 Uhr15.10.2008 13:47:16 Uhr
33 DVB-S Receiver
GB
4.6 Satellite Guide
When you enter “Satellite Guide” menu, you
will see the screen like beside:
Here you can enter your local longitude and
latitude and the satellite’s longitude. The
receiver calculates the antenna’s orientation
and elevation to point your antenna to the
selected satellite.
1. Use the [Number] buttons to input the
values of “Local Longitude”, “Local Latitude”
and “Satellite Longitude”.
2. In the “Calculate” item press [OK], the receiver auto calculates the antenna’s
orientation and elevation to point your antenna to the selected satellite.
3. Press [Menu/Exit] to return to the previous menu.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 33BDA Imperial DB 2_GB_TO.indd 33 15.10.2008 13:47:17 Uhr15.10.2008 13:47:17 Uhr
32Installation Guide
GB
4.5 TP List
When you open the “TP List” menu you will
see a window like the one beside.
1. Press [Vol
] to change the marked
satellite.
2. Press [Red] button to open the “Edit TP”
menu. Here you can edit the transponder’s
data.
3. Press [Green] button to open the “Add
TP” menu. Here you can add a new TP and
setup its parameters.
4. Press [Yellow] button will open a dialog
box asking you to confi rm the deletion of
the current TP. If you select “OK” all the re-
lated channels will be deleted. If you select
“Cancel” the operation will be cancelled.
5. Pressing the [Blue] button will open a dia-
log box asking you to confi rm the deletion
of all TP on current satellite. If you select
“OK”, all TP of the current satellite will be
deleted. If you select “Cancel” the opera-
tion will be cancelled.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 32BDA Imperial DB 2_GB_TO.indd 32 15.10.2008 13:47:17 Uhr15.10.2008 13:47:17 Uhr
31 DVB-S Receiver
GB
4.4 Satellite List
When you enter the “Satellite List” menu you
can see a window like the one beside:
1. Press [Red] button to enter edit satellite
menu. You can edit the satellite’s name
and its longitude.
2. Press [Green] button to open the “Add
satellite” window.
3. After pressing [Yellow] button you will be
asked “Are you sure to delete?”. Select
“OK” to delete the marked satellite. Select
“Cancel” to cancel the operation.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 31BDA Imperial DB 2_GB_TO.indd 31 15.10.2008 13:47:19 Uhr15.10.2008 13:47:19 Uhr
30Installation Guide
GB
• LNB Type: Press [Vol ] to switch
among “Standard”, “User” and “Univer-
sal” mode.
For Example: If you use a Dual LNB,
then you should select “User” option
in “LNB Type” and set the correct fre-
quency in LNB type.
• 22K: Use [Vol
] to switch “ON” and
“Off”. The 22KHz signal is used in KU
universal LNBs to change between low band and high band.
! Notice:
After choosing LNB type “Universal” you cannot modify 22K.
• DiSEqC1.0: Use [Vol ] to switch the options or press [OK] to open the DiS-
EqC1.0 option list to select directly with [CH ], press [OK] to confi rm it.
• DiSEqC1.1: Use [Vol ] to switch DiSEqC1.1 option or press [OK] to enter
DiSEqC1.1 option to select directly with [CH ], press [OK] to confi rm it. The op-
tions of this item are: Disable/CCard1 M1 Port1/CCard1 M1 Port2/
CCard1 M1 Port3/CCard1 M1 Port4/CCard1 M2 Port1/CCard1 M2 Port2/
CCard1 M2 Port3/CCard1 M2 Port4/CCard1 M3 Port1/CCard1 M3 Port2/
CCard1 M3 Port3/CCard1 M3 Port4/CCard2 Port1/CCard2 Port2/
CCard2 Port3/CCard2 Port4/CCard2 Port5/CCard2 Port6/CCard2 Port7/
CCard2 Port8/CCard2 Port9/CCard2 Port10/CCard2 Port11/
CCard2 Port12/CCard2 Port13/CCard2 Port14/CCard2 Port15/
CCard2 Port16.
• Positioner: Press [Vol ] to select between “Off/DiSEqC1.2/USALS”.
! Notice:
When you select “DiSEqC1.2 or USALS”, “DiSEqC1.0” and “DiSEqC1.1” items will be
disabled.
• Polarity: Press [Vol ] to switch between “Auto/H/V ”.
• Toneburst: Press [Vol ] to switch this function “On” or “Off”.
5. After you completed your modifi cation, on the “TP Scan” item, press [OK] twice to
start scanning.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 30BDA Imperial DB 2_GB_TO.indd 30 15.10.2008 13:47:20 Uhr15.10.2008 13:47:20 Uhr
29 DVB-S Receiver
GB
4. INSTALLATION
4.3 TP Scan
When you enter “TP Scan” menu a window
like the one beside will be displayed.
1. In the “Satellite” item press [Vol
] to
select the satellite which you want to scan
or press [OK] to open the “satellite list” to
select directly with [CH ], press [OK]
to confi rm it.
2. TP Index: Use [Vol ] to select the desired transponder or press [OK] to open the
TP list to select directly with [CH ], press [OK] again to display the TP number
where the channel can be found. Press [Red/Green/Yellow] key on the RCU for the
related functions.
•
When you press [Red] it will display “New TP” in “TP Index” item. You have to set the
parameters of “TP Frequency”, “Symbol Rate” for this new transponder. Therefore
use the number buttons of the RCU. The available range are “3000
~
13450MHz” and
“1000
~
45000KS/s”.
• When you press [Green] a safety question will be displayed for confi rmation to delete
the current transponder or not. If you select “OK”, the current transponder will be
deleted and the total number of transponders will be reduced.
• When you press [Yellow] a safety question will be displayed for confi rmation to delete
all transponders or not. If you select “OK”, the all transponders on current satellite will
be deleted.
3.
For existing transponders you also can use number buttons to modify the parameters
of “TP Frequency” and “Symbol Rate” or [Vol ] to change the value directly.
“Polarity” and “FTA only” are used for setting scans conditions. Press [Vol ] to
select a different mode.
• On “TP Scan” item, press [OK] will open another window where you can set “Scan
Mode”, “Program Type” and “NIT Search”. Press [Menu/Exit] to return to the
previous menu.
• Press [Red] button to add a new TP.
• Press [Green] button to delete the current TP.
• Press [Yellow] button to delete all transponders on current satellite
4. Antenna Setup: Press [OK] to enter LNB confi guration, you will see a window like beside:
BDA Imperial DB 2_GB_TO.indd 29BDA Imperial DB 2_GB_TO.indd 29 15.10.2008 13:47:21 Uhr15.10.2008 13:47:21 Uhr
28Installation Guide
GB
4. INSTALLATION
4.2 Multi Search
When you enter the “Multi Search” menu a
window like the one beside will open.
1. In the “Satellite” item press [Vol
] to
select the satellite which you want to scan
or press [OK] to open the “satellite list” to
select directly with [CH ], and press
[OK] to mark/unmark and [MENU] to
fi nish the selection. You can select several
satellites in this menu. The system will use DiSEqC1.0/1.1, DiSEqC1.2 and USALS
functions to search the marked satellites and scan channels.
2. On “FTA Only” item, pres [Vol ] to select scanning of all channels or just scanning of
free channels. If you select “Yes”, it will scan free channels only.
3. On “Scan Channel” item, press [Vol ] to select the scanning range from TV + radio
channels, only TV channels or only radio channels.
4. On “Scan Mode” item, you can select “Auto Scan”, “Preset Scan” or “NIT Search” to
blind scan preset transponders or network transponders of the selected satellite.
5. Select “Search” and press [OK] to start scanning. In the lower part of the window the
progress of scanning and the found channels are displayed.
6. Press [Menu/Exit] to cancel or fi nish the scanning and saving the found channels.
BDA Imperial DB 2_GB_TO.indd 28BDA Imperial DB 2_GB_TO.indd 28 15.10.2008 13:47:22 Uhr15.10.2008 13:47:22 Uhr
27 DVB-S Receiver
GB
• DiSEqC1.0: Use [Vol ] to switch the options or press [OK] to open the
DiSEqC1.0 option list to select directly with [CH
], press [OK] to confi rm it.
• DiSEqC1.1: Use [Vol ] to switch DiSEqC1.1 option or press [OK] to enter
DiSEqC1.1 option to select directly with [CH ], press [OK] to confi rm it.
The options of this item are: Disable/CCard1 M1 Port1/CCard1 M1 Port2/
CCard1 M1 Port3/CCard1 M1 Port4/CCard1 M2 Port1/CCard1 M2 Port2/
CCard1 M2 Port3/CCard1 M2 Port4/CCard1 M3 Port1/CCard1 M3 Port2/
CCard1 M3 Port3/CCard1 M3 Port4/CCard2 Port1/CCard2 Port2/
CCard2 Port3/CCard2 Port4/CCard2 Port5/CCard2 Port6/CCard2 Port7/
CCard2 Port8/CCard2 Port9/CCard2 Port10/CCard2 Port11/
CCard2 Port12/CCard2 Port13/CCard2 Port14/CCard2 Port15/CCard2
Port16.
• Positioner: Press [Vol ] to select between “Off/DiSEqC1.2/USALS”.
Notice: When you select “DiSEqC1.2 or USALS”, “DiSEqC1.0” and “DiSEqC1.1”
items will be disabled.
• Polarity: Press [Vol ] to switch between “Auto/H/V ”.
• Toneburst: Press [Vol ] to switch this function “On” or “Off”.
3. DiSEqC1.0 4Port: Use [Vol ] to switch the options of DiSEqC1.0. Between Dis-
able/LNB1/LNB2/LNB3/LNB4.
4. TP Index: Us [Vol ] to select the desired transponder or press [OK] to open the
TP list to select directly with [CH ], press [OK] again to display the TP number
where the channel can be found.
5. FTA Only: Press [Vol ] to select to scan only free channels or even scrambled
channels. If you select “Yes” it will scan free channels only.
6. Scan Channel: Press [Vol ] to select to scan TV + radio channels, or just TV
channels or just radio channels.
7. Scan Mode: You can select “Auto Scan”, “Preset Scan” or “NIT Search” to blind scan
preset transponders or network transponders of the selected satellite.
8. Search: Press [OK] to start scanning. In the lower part of the window the progress
of scanning and the found channels are displayed.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 27BDA Imperial DB 2_GB_TO.indd 27 15.10.2008 13:47:22 Uhr15.10.2008 13:47:22 Uhr
26Installation Guide
GB
After selecting the installation menu you can see the window like beside.
In “Installation” menu:
1. Press [CH
] to select menu items
among Single Search, Multi Search, TP
Scan, Satellite List, TP List and Satellite
Guide.
2. Press [OK] to enter the selected item.
4.1 Single Search
After selecting “Single Search” you will see a
window like beside:
1. In the “Satellite” item press [Vol ] to
select the satellite which you want to scan
or press [OK] to open the “satellite list” to
select directly with [CH ], press [OK]
to confi rm it.
2. LNB Confi guration: Press [OK] to enter
LNB confi guration, you will see a window
like beside:
• LNB Type: Press [Vol ] to switch
among “Standard”, “User” and “Univer-
sal” mode.
For Example: If you use a Dual LNB,
then you should select “User” option
in “LNB Type” and set the correct fre-
quency in LNB type.
• 22K: Use [Vol ] to switch “ON” and
“Off”. The 22KHz signal is used in KU
universal LNBs to change between low
band and high band.
Notice: After choosing LNB type “Universal” you cannot modify 22K.
4. INSTALLATION
BDA Imperial DB 2_GB_TO.indd 26BDA Imperial DB 2_GB_TO.indd 26 15.10.2008 13:47:23 Uhr15.10.2008 13:47:23 Uhr
25 DVB-S Receiver
GB
3.7 Save channel list and settings
To save channel list and settings.
1. Enter the password. The default password
is “0000”.
2. After entering the password correct a
safety question will show up where you
have to confi rm fi rst.
3. Select “OK”, press [OK] to save current
channel list to backup channel list.
Select “Cancel” press [OK] to cancel the
operation.
3. CHANNEL
BDA Imperial DB 2_GB_TO.indd 25BDA Imperial DB 2_GB_TO.indd 25 15.10.2008 13:47:24 Uhr15.10.2008 13:47:24 Uhr
24Installation Guide
GB
3.5 Delete All
To delete all channels:
1. Enter the password. The default password
is “0000”.
2. After entering the password correct a
safety question will show up where you
have to confi rm fi rst
3. Select “OK” to delete all channels or
“Cancel” to cancel the operation and
confi rm with [OK].
4. In step 1 and step 2, pressing [Menu] will exit the function directly without saving.
? Frequently Asked Question
Q: IF I incautiously delete all channels, what should I do?
A: there are two ways to restore:
• To research all channels in the “Installation” menu.
• Use “Factory Default” function to restore all channels in the “Tools” menu.
3.6 Restore channel list and settings
To restore channel list and settings.
1. Enter the password. The default password
is “0000”.
2. After entering the password correct a
safety question will show up where you
have to confi rm fi rst.
3. Select “OK”, press [OK] to restore the last
backup channel list, the current channel
list will be erased. Select “Cancel” press
[OK] to cancel the operation.
3. CHANNEL
BDA Imperial DB 2_GB_TO.indd 24BDA Imperial DB 2_GB_TO.indd 24 15.10.2008 13:47:25 Uhr15.10.2008 13:47:25 Uhr
23 DVB-S Receiver
GB
2. Channel Play type: Use [CH ] to
select, press [OK] to enter “Channel Play
Type” menu. Here you can select the
“playing channels” as “All”, “Free” or
“Scrambled” with [Vol ].
3. If you select “Free” then all scrambled
channels will be skipped when you change
channels with [Vol ].
4. Press [Exit] to leave the “Channel Setup”
menu.
3.4 Favorite group list name
• When you enter “Favorite group list
name” menu with 8 favorite group will
be displayed, press [OK] on the RCU to
rename favorite group. Use [CH ]/
[Vol ], to select character, press [OK]
to confi rm it.
• After modifi cation select “OK” of button
bar and press [OK] on the RCU to rename
the favorite group name and leave the
edit mode. Press [Exit] on the RCU to exit
the edit mode without saving the favorite
group name.
3. CHANNEL
BDA Imperial DB 2_GB_TO.indd 23BDA Imperial DB 2_GB_TO.indd 23 15.10.2008 13:47:26 Uhr15.10.2008 13:47:26 Uhr
22Installation Guide
GB
3.1.5 Find
1. Press [Blue] button to open the “Find”
window like showed beside. Press
[CH ]/[Vol ] to select the leading
character of the channel name and press
[OK] to confi rm it.
2. After entering the character(s) highlight
“OK” in the window and press [OK] on the
RCU.
3. Press [Exit] button to close the fi nd window and brings you back to the channel list.
3.2 Radio Channel List
Basically the operation of “Radio Channel List” is same as “TV Channel List”, except that
in the small channel window the radio Logo will be displayed.
3.3 Channel Setup
When you enter the “Channel Setup” menu
you will see a screen like beside:
1. Startup Channel: Press [OK] to enter
“Startup Channel” menu to see the screen
like showed beside:
• If you set of “Boot on Channel” to “On”
you can edit the following two items.
If the setting is “Off” the box always
starts with the channel that was run-
ning when the box has been switched
off.
• On the “Mode” item you can select
either “TV channel” or “Radio channel”.
• On “Startup Channel” item you can
open the channel list by pressing [OK].
Then you can select the channel of you
choice. Press [OK] again to confi rm.
3. CHANNEL
BDA Imperial DB 2_GB_TO.indd 22BDA Imperial DB 2_GB_TO.indd 22 15.10.2008 13:47:26 Uhr15.10.2008 13:47:26 Uhr
21 DVB-S Receiver
GB
• Edit
Press [Red] button to edit the channel.
1. Selecting the name item with [OK] will
display a button pad to show you how
to edit the channel name.
2. On the “Video PID”, “Audio PID” and
“PCR PID” items you can input num-
bers to modify the item’s value.
3. After modifi cation select “Save” and press [OK] button to save the modifi ed values
and exit “Edit” mode. Or select “Exit” and press [OK] to leave edit mode without
saving the modifi cations.
• Create
Press [Green] button to open the create
channel window.
1. Press [OK] on the “Satellite” item to
display the satellite list. You can select
the satellite for which you want to
create a new channel.
2. With marked “TP Index” item press
[OK] to display TP list, use [CH ] to select for which you want to create a new
channel. Press [OK] to display the TP number where the channel can be found.
The next three items will show the related parameters.
3. Highlight the “Name” item and press [OK] to display the button pad and edit the
new channel’s name. In “Video PID”, “Audio PID” and “PCR PID” items you can enter
the numbers directly to set these parameters of the new channel.
4. After modifi cation select “Save” and press [OK] to save the new channel and leave
the edit mode. Select “Exit” and press [OK] to exit the edit mode without saving the
new channel.
3. CHANNEL
BDA Imperial DB 2_GB_TO.indd 21BDA Imperial DB 2_GB_TO.indd 21 15.10.2008 13:47:27 Uhr15.10.2008 13:47:27 Uhr
20Installation Guide
GB
3. CHANNEL
3.1.4.1 Delete
In channel edit menu press [Red] button will open another window where you can
choose between delete one channel and delete all channel.
• Del One
Press [Red] button to mark a channel for deleting. Marked channel will be deleted
after you confi rm to save the changes when you leave this menu.
• Del All
a) Press [Green] button to show a deleting icon behind all channel name.
b) Press [MENU] button you will be asked “Are you sure to save?”. Select “OK” to
delete all channel. Select “Cancel” to cancel the operation.
3.1.4.2 Skip
In channel edit menu, press [Green] button to place a skip icon behind the name of the
highlighted channel. Marked channels will be skipped when you change channels in TV
mode after you confi rm to save the changes when you leave this menu.
3.1.4.3 Lock
In channel edit menu, press [Yellow] button to place a lock icon behind the name of the
highlighted channel. Marked channels will be locked and displayed only after password
has been entered if you confi rm to save the changes when you leave this menu.
3.1.4.4 Edit
Pressing the [Blue] button in the TV channel
list
edit menu will open another window where
you can choose between edit the actual
channel and create a new channel.
BDA Imperial DB 2_GB_TO.indd 20BDA Imperial DB 2_GB_TO.indd 20 15.10.2008 13:47:28 Uhr15.10.2008 13:47:28 Uhr
19 DVB-S Receiver
GB
3. CHANNEL
3.1.3 Sort
Press [Green] to open the sort window.
Press [CH ] to select and [OK] to
confi rm your choice.
The ways of sorting are:
• Default: Sort channel factory default.
• FTA/CAS: Sort channel by free and
scrambled sequence. Free channels will
be listed fi rst and scrambled channels
behind in the channel list.
• Lock: Unlocked channels are listed fi rst end locked channels at the end.
• Name (A-Z): Sorting in Alphabetical order, ignoring “$” symbol.
• Name (Z-A): Sorting in Alphabetical order, ignoring “$” symbol.
3.1.4 TV Channel List Edit
• After pressing the [Yellow] button a
window for entering the password will
open. The default password is “0000”.
• You can delete, skip, lock and edit the
channel.
• Press [MENU] to leave the channel edit-
ing. The system will ask you to confi rm the
saving of the changes you made.
BDA Imperial DB 2_GB_TO.indd 19BDA Imperial DB 2_GB_TO.indd 19 15.10.2008 13:47:29 Uhr15.10.2008 13:47:29 Uhr
18Installation Guide
GB
3. CHANNEL
3.1.1 Favorite
1. Press [FAV] to open the favorite window.
2. You can select between 8 favorite groups
with [CH ]. Press [OK] to assign the
channel to a favorite group, press [EXIT]
to exit favorite group.
3. Press [OK] again to remove the channel
from the marked favorite group.
4. Press [MENU] button you will be asked
“Are you sure to save?”. Select “Yes” to
save the marked favorite group. Select “No” to cancel the operation.
5. To return to the TV channel list. The channels of favorite groups are indicated with a
favorite icon behind the name.
3.1.2 Move
Pressing the [Red] button in the TV channel
list will open another window where you can
choose between move the actual channel
and swap the actual channel to the desired
position, press [OK] to confi rm it.
a) Move
1. Press [Red] button to show a moving icon behind the channel name.
2. Move the channel to the desired position with [CH ]. Press [OK] to confi rm the
position.
b) Swap
1. Press [Green] button to show a moving icon behind the channel name.
2. Move the channel to the desired position with [CH ] to confi rm the position.
BDA Imperial DB 2_GB_TO.indd 18BDA Imperial DB 2_GB_TO.indd 18 15.10.2008 13:47:30 Uhr15.10.2008 13:47:30 Uhr
17 DVB-S Receiver
GB
3. CHANNEL
Press [Menu] in the TV/radio mode to enter
the main menu.
1. Press [CH ] to select the channel
item.
2. Press [OK] to enter the selected item.
In the channel menu:
• Press [CH ] to select the wanted
menu item among TV Channel List, Radio
Channel List, Channel setup, Favorite
group list name, Delete All, Restore
channel list and settings and Save channel
list and settings
• Press [OK] to enter the selected item.
3.1 TV Channel List
If you enter the channel list menu a window
like the one below will open.
1. You can move the highlighted channel
with [CH ] and press [OK] to preview
the highlighted program in the preview
window.
2. Press [PGUP/PGDN] on the RCU to jump
between the channels by pages.
3. Press [Vol ] to switch satellite of the
program group.
4. Press [Menu] or [Exit] buttons to enter TV playing mode.
5. The color buttons offer further functions to manage the channel list.
BDA Imperial DB 2_GB_TO.indd 17BDA Imperial DB 2_GB_TO.indd 17 15.10.2008 13:47:31 Uhr15.10.2008 13:47:31 Uhr
16Installation Guide
GB
2. BASIC OPERATIONS
2.24 SAT
1. In TV mode, press [OK] button, then press
the [Yellow] button to open satellite list
and select there, then press [OK] to open
“TV Channel List” menu, select channel of
the current.
2. In TV mode, press [Page Up/Down] to
switch directly between satellites.
2.25 LNB Short
When LNB is short, it will notify user on screen “LNB Short!” Please check your cables
and connections for shorts. When the short is removed the warning message will
disappear.
BDA Imperial DB 2_GB_TO.indd 16BDA Imperial DB 2_GB_TO.indd 16 15.10.2008 13:47:32 Uhr15.10.2008 13:47:32 Uhr
15 DVB-S Receiver
GB
2.20 TXT
1. Press [TXT] button in TV mode to open
the teletext page. This service is depend-
ing on the support of the channel provider.
2. If the channel does not support teletext
information, it will show “No Teletext Data”
on the screen.
2.21 INFO
• In TV mode, press [INFO] button can open
information screen, in the window shows
the parameters of current channel.
• Two dynamic bars at the bottom of the
window refl ect the signal intensity and
signal quality of the current channel.
2.22 TV/Radio
In TV mode, press [TV/Radio] to switch to Radio mode. In Radio mode press [TV/Radio]
again to switch back to TV mode.
2.23 Recall
Pressing the [Recall] button allows you to toggle between the actual and the last se-
lected channel.
2. BASIC OPERATIONS
BDA Imperial DB 2_GB_TO.indd 15BDA Imperial DB 2_GB_TO.indd 15 15.10.2008 13:47:32 Uhr15.10.2008 13:47:32 Uhr
14Installation Guide
GB
2. BASIC OPERATIONS
2.17 FAV
1. In TV mode press the [FAV] button to
display the Favorite Group window on the
screen as the picture beside shows.
2. In the Favorite Group window you can
select the desired favorite channel with
[CH ] and confi rm it with [OK] to
switch to it. In bigger groups you can navi-
gate with [PGUP/ PGDN].
3. With [Vol ] you can select different
Favorite Groups.
4. Press [Exit] to close the Favorite Group window.
? Frequently Asked Question
Q: Why the screen displays “No Favorite Channel” after pressing the [Favorite] button?
A: No channels have been assigned to a Favorite Group yet. You can do this in the
channel menu.
2.18 List
In TV mode, press [List] button to access directly to the “TV Channel List” menu or to
the “Radio Channel List” menu.
2.19 PAUSE
1. In playing mode, press [PAUSE], the picture will be paused, but the sound of the
channel will still continues.
2. Press [PAUSE] again, the screen’s picture will skip over to the current playing picture,
and the sound of the channel will corresponding playing.
BDA Imperial DB 2_GB_TO.indd 14BDA Imperial DB 2_GB_TO.indd 14 15.10.2008 13:47:33 Uhr15.10.2008 13:47:33 Uhr
13 DVB-S Receiver
GB
2. BASIC OPERATIONS
4. Press the [Yellow] button in the EPG
menu to program a timer with the actual
events data.
5. To close the EPG menu press [Exit].
2.14 Audio
1. In TV mode, press the [Audio] button to
open the Audio Mode window.
2. Select the item you want to adjust with
[CH ] and change the value with
[Vol ].
2.15 SUB
Sub (Subtitle): In “OSD Setting” menu, use [Vol ], to select. If the current channel has
subtitle information, it will be displayed if this function is “On”. If this function is “Off”
subtitles won’t be displayed.
2.16 Zoom
1. The [Zoom] key allows you to magnify a
certain area on the images and the
current screen will show
2. Press [Zoom] key again, the image will
enlarge rotate as x1, x2, x4, x6, x8, x12,
x16.
3. In “x2
~
x16” image, using [CH /
Vol ] keys to move the image center
area you want to see.
4. In zoom mode, press [Exit] to close “Zoom” window.
BDA Imperial DB 2_GB_TO.indd 13BDA Imperial DB 2_GB_TO.indd 13 15.10.2008 13:47:34 Uhr15.10.2008 13:47:34 Uhr
12Installation Guide
GB
2. BASIC OPERATIONS
2.11 Menu
Press [Menu] button to enter or exit the current menu.
2.12 Exit
Press [Exit] button to exit the current menu.
2.13 EPG
1. The STB supports Electronic Program
Guides (EPG) to give you information about
the actual programs of certain channels
like event name, subtitle, description, start
and fi nish time. This feature is depending
on the service of the channel provider.
Press [EPG] to open the EPG window.
2. The [Red] button opens the detailed
schedule of the marked channel. You can
select an event with [CH ] and display
the event’s detailed description with [OK].
3. Press the [Green] button in the EPG menu
to display the detailed information of the
actual event in the selected channel. With
the [Yellow] button you can program a
timer with the start and fi nish time and
date of this event.
BDA Imperial DB 2_GB_TO.indd 12BDA Imperial DB 2_GB_TO.indd 12 15.10.2008 13:47:35 Uhr15.10.2008 13:47:35 Uhr
11 DVB-S Receiver
GB
2. BASIC OPERATIONS
2.7 FAV +/-
1. In full screen, press [FAV +/-] keys can switch the favorite channels in current satel-
lite channels list directly.
2. The sequence of the switch favorite channels is following the sequence that in the
current satellite channel list, not follow the sequence in the favorite group.
2.8 CH
In TV/Radio mode press [CH ] to change channel.
2.9 Vol
In TV/Radio mode, press [Vol ], to adjust volume.
2.10 OK
1. In TV mode press [OK] button to open the
Channel List window.
2. Press the [Red] exchange screen.
3. Press [Green] button to sort the channels
by free and scrambled channels. Free
channel are listed fi rst and scrambled
channels last
4. Press [Yellow] button to open the SAT
list. After selecting a satellite the channel
list will be reduced to the channels of this
satellite.
5. Press [FAV] button to open FAV list. After
selecting a Favorite Group the channel
list will be reduced to the channels of this
group.
6. Press [Blue] button to open the Find
window. You can use this feature to fi nd
channel by their names.
7. Press [OK] to change and display the
marked channel.
BDA Imperial DB 2_GB_TO.indd 11BDA Imperial DB 2_GB_TO.indd 11 15.10.2008 13:47:36 Uhr15.10.2008 13:47:36 Uhr
10Installation Guide
GB
2. BASIC OPERATIONS
2.3 Mute
1. Press the [Mute] button to mute the sound. On the screen an icon will be displayed
to indicate the muted sound.
2. Press the [Mute] button again to restore the sound.
2.4 Channel Number
In TV mode you can enter the channel number directly with your remote control unit and
confi rm the number with the OK button to change to the desired channel.
2.5 MULTI-PIC
In TV mode, press [0] key to enter the
“MULTI-PIC” menu.
1. In “MULTI-PIC” menu, you can choose
channels’ preview window (static),
starting from the current channel.
Only the marked preview program is
continuously playing.
2. Press [CH /Vol ], to change the
marked channel among the preview pro-
grams.
3. With the number buttons [1]
~
[9] you can directly move the highlight to the related
channel.
4. With [OK] you return to full screen mode in the marked channel.
2.6 PGUP/PGDN
In TV mode, press [PGUP/PGDN] to switch directly between satellites.
BDA Imperial DB 2_GB_TO.indd 10BDA Imperial DB 2_GB_TO.indd 10 15.10.2008 13:47:37 Uhr15.10.2008 13:47:37 Uhr
9 DVB-S Receiver
GB
2.1 Switch on STB
Switch the [Device’s Main Power] switch on.
When the STB is fi rst used it will display “Quick Setup” window. you will set Language,
First Audio, Second Audio, LNB Power, Antenna Setup and Multi Search.
? Frequently Asked Question
Q: The power of my STB is on and it is running in TV mode but the TV screen shows
nothing:
A: Make sure the TV set has been set to the correct video input (not the TV channels).
For example, if you have connected the unit to the video1 input of the TV set then you
need to select the corresponding input of the TV. Mostly it is done with the AV button
of the TVs remote control unit.
Q: My STB is running in TV mode but the TV screen shows nothing except one ball
and “No Signal”.
A: That means the channel you selected has no signal. This can be caused by several
reasons:
1. The channel you selected is not from the satellite to which your dish is pointing.
Select another channel.
2. The signal of current TV channel is too weak. You can try to change to other
channels with a stronger signal. If the problems still exist, please consult your local
dealer or installer for technical service.
3. You selected the wrong LNB type in the installation menu or your DiSEqC switch
confi guration is not correct.
2.2 Standby Mode
1. Press [Power] button to switch from TV/radio mode to standby mode
2. In standby mode press [Power] button again to switch back to TV/radio mode. The
last active channel will be showed.
3. To switch off the STB complete press the main power button.
2. BASIC OPERATIONS
BDA Imperial DB 2_GB_TO.indd 9BDA Imperial DB 2_GB_TO.indd 9 15.10.2008 13:47:37 Uhr15.10.2008 13:47:37 Uhr
8Installation Guide
GB
1. REMOTE CONTROL & PANEL DESCRIPTION
1.3 Remote Control
BDA Imperial DB 2_GB_TO.indd 8BDA Imperial DB 2_GB_TO.indd 8 15.10.2008 13:47:38 Uhr15.10.2008 13:47:38 Uhr
7 DVB-S Receiver
GB
1.2 Rear Panel Description
1. POWER ON/OFF: Allows to completely switch off the receiver.
2. AC IN: Mains input cable.
3. IF IN: Satellite input.
4. IF OUT: Satellite output for cascading to other devices
Note: The operation of another receiver at the same time is only possible with
limited channel selection.
5. S/PDIF: Optical output for digital audio (AC3)
6. S/PDIF: Coaxial output for digital audio (AC3)
7. RS-232: Serial Port allowing software upgrades.
8. AUDIO: HiFi outputs for stereo set.
9. VIDEO: CVBS video output for TV AV in.
10. TV SCART: Output SCART for the connection to a TV set.
11. VCR SCART: Output SCART for the connection to a VCR set.
1. REMOTE CONTROL & PANEL DESCRIPTION
1
4
23 9
10 11 7
8 56
BDA Imperial DB 2_GB_TO.indd 7BDA Imperial DB 2_GB_TO.indd 7 15.10.2008 13:47:38 Uhr15.10.2008 13:47:38 Uhr
6Installation Guide
GB
1.1 Front Panel Description
1. POWER: Is used to switch between the working mode and the standby mode.
2. Display (4-Digit/7-Segment): Displays the received channel number while
operating and time while in standby mode.
3. Remote Sensor: Detects the infrared signals from the remote control unit.
4. MENU: To enter into the main menu and exit all menus.
5. VOL+/-: To change volume to move cursor, change numbers in the menu or to
change the choice.
6. OK: To select an item in the menu and confi rm it or pop up channel list when no
menu.
7. CH+/-: To change channels or for navigating and changing values in menus.
1. REMOTE CONTROL & PANEL DESCRIPTION
2
1 4 65 7
3
BDA Imperial DB 2_GB_TO.indd 6BDA Imperial DB 2_GB_TO.indd 6 15.10.2008 13:47:39 Uhr15.10.2008 13:47:39 Uhr
5 DVB-S Receiver
GB
3. CHANNEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3.1 TV Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3.1.1 Favorite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.1.2 Move . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.1.3 Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.1.4 TV Channel List Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.1.5 Find . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3.2 Radio Channel List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3.3 Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
3.4 Favorite group list name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.5 Delete All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.6 Restore channel list and settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
3.7 Save channel list and settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
4. INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
4.1 Single Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
4.2 Multi Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4.3 TP Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
4.4 Satellite List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
4.5 TP List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
4.6 Satellite Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
5. SYSTEM SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
5.1 Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
5.2 TV System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
5.3 Time & Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
5.4 OSD Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
5.5 Parental Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
5.6 Power setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
5.7 RCU Position Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
6. TOOLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
6.1 Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
6.2 Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
6.3 Game . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
6.4 Factory Default. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
6.5 Software Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
6.5.1 Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
6.5.2 Upgrade by Satellite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
6.6 SatcoDX Auto Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
7. TECHNICAL SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
CONTENTS
BDA Imperial DB 2_GB_TO.indd 5BDA Imperial DB 2_GB_TO.indd 5 15.10.2008 13:47:41 Uhr15.10.2008 13:47:41 Uhr
4Installation Guide
GB
1. REMOTE CONTROL & PANEL DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . 6
1.1 Front Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
1.3 Remote Control Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. BASIC OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Switch on STB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.4 Channel Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.5 MULTI-PIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.6 PGUP/PGDN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.7 FAV +/- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.8 CH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.9 Vol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.10 OK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.11 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.12 Exit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.13 EPG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.14 Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.15 SUB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.16 Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.17 FAV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
2.18 List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
2.19 PAUSE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
2.20 TXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.21 INFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.22 TV/Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.23 Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.24 SAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.25 LNB Short . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
CONTENTS
BDA Imperial DB 2_GB_TO.indd 4BDA Imperial DB 2_GB_TO.indd 4 15.10.2008 13:47:41 Uhr15.10.2008 13:47:41 Uhr
3 DVB-S Receiver
GB
SICHERHEITSHINWEISE
Attachments: Never add any attachments and/or equipment without the
manufacturer consent; as such additions may result in the risk of fi re, electric shock
or other personal injury.
Locating: Slots and openings in the cabinet are provided for ventilation to protect it
from overheating. Do not block these openings or allow them to be blocked by placing
the STB on a bed, sofa or other similar surface, nor should it be placed over a radiator
or heat register.
Power-Cord Protection: Place the power-supply cord out of the way, where it will
not be walked on. Please take special attentions to cords at plugs, convenience
receptacles and the point where they exit from the unit.
Object and Liquid Entry: Never put objects of any kind into this STB through openings,
as they may touch dangerous voltage points or short-out parts that could result in a
fi re or electric shock. Never spill any liquid on the STB.
Note: Moisture may be formed inside the unit in the following conditions:
When the unit is suddenly moved from a cold environment or an air-condition room to
a warm place.
Immediately after a heater has been turned on.
In a steamy or very humid room.
If the moisture forms inside the unit, it may not operate properly. To correct this
problem, turn on the power and wait about two hours for the moisture to evaporate.
Parts Replacement: When the unit parts need to be replaced, user should make sure
the service technician use the replacement parts specifi ed by the manufacturer or
having the same characteristics as the original part. Unauthorized replacement may
put the unit in the risk of fi re, electric shock or other hazards.
Safety Check: After all the maintenances and repairs are done, user is required to
request the service technician to conduct the overall safety check to ensure the
machine is in the proper condition.
BDA Imperial DB 2_GB_TO.indd 3BDA Imperial DB 2_GB_TO.indd 3 15.10.2008 13:47:42 Uhr15.10.2008 13:47:42 Uhr
2Installation Guide
GB
SAFETY PRECAUTION
CAUTION:
The lightning fl ash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user
to „dangerous voltage“ and
to prevent from a risk of
electric shock.
Warning:
To reduce the risk of
electric shock, don‘t
open the cabinet. Refer
servicing to qualifi ed
personnel only.
The exclamation point
within an equilateral
triangle is intended to alert
the user to important
operating and maintenance
(servicing).
WARNING: Do not use this STB where contact with or immersion in water is a
possibility. Do not use near fl ower vase, washbowls, kitchen sinks, laundry tubs,
swimming pools, etc.
WARNING: Do not put the candle or lamp stand on the cabinet; otherwise, there is the
danger of fi re.
WARNING: The unit should be connected to a power supply only of the type descry
bed in the operating instructions or as marked on the unit. If you are not sure of the
type of power supply(for example: 120 or 230V) to your home, consult your local
dealer or local power company.
WARNING: Do not open the cabinet or touch any parts in the inner mechanism.
Consult your local dealer for technical service if the opening is required.
Note: To ensure proper use of this product, please read this user manual carefully
and retain for further reference.
Note: Do not open the cabinet to avoid the unit direct exposure to radiation.
Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and
remote control with a soft cloth lightly moistened with a mild detergent solution.
BDA Imperial DB 2_GB_TO.indd 2BDA Imperial DB 2_GB_TO.indd 2 15.10.2008 13:47:42 Uhr15.10.2008 13:47:42 Uhr
Installation Guide
DVB-S Receiver
See the world through
BDA Imperial DB 2_GB_TO.indd 1BDA Imperial DB 2_GB_TO.indd 1 15.10.2008 13:47:43 Uhr15.10.2008 13:47:43 Uhr
… 46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Digitalbox IMPERIAL DB 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Digitalbox IMPERIAL DB 2 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Digitalbox IMPERIAL DB 2

Digitalbox IMPERIAL DB 2 Gebruiksaanwijzing - Deutsch - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info