Handleiding Digitalbox IMPERIAL DB 2 USB (pagina 33 van 54) (Engels)

499302

Verklein

Vergroot

Pagina terug

1/54

Pagina verder

Installation Guide

IMPERIAL DB 2 USB

See the world through

Installation Guide

SAFETY PRECAUTION

CAUTION

The lightening ﬂ ash with

arrowhead symbol, within

an equilateral triangle, is

intended to alert the user

to „dangerous voltage“ and

to prevent from a risk of

electric shock.

To reduce the risk of elec-

tric shock, don‘t open the

cabinet. Refer servicing to

qualiﬁ ed personnel only.

To reduce the risk of elec-

tric shock, don‘t open the

cabinet. Refer servicing to

qualiﬁ ed personnel only.

WARNING: The exclamation point within an equilateral triangle is intended to alert

the user to important operating and maintenance(servicing). The apparatus shall

not be exposed to dripping or splashing and that no objects ﬁ lled with liquids, such as

vases,shall not be placed on the apparatus

WARNING: Do not put the candle or lamp stand on the cabinet; otherwise, there is

the danger of ﬁ re.

WARNING: The unit should be connected to a power supply only of the type descry

bed in the operating instructions or as marked on the unit. If you are not sure of the

type of power supply(for example: 120 or 230V) to your home, consult your local

dealer or local power company.

WARNING: Do not open the cabinet or touch any parts in the inner mechanism. Con-

sult your local dealer for technical service if the opening is required.

WARNING: The MAINS plug is used as the disconnect device, the disconne ctdevice

shall remain readily operable.

Note: Do not open the cabinet to avoid the unit direct exposure to radiation.

Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and

remote control with a soft cloth lightly moistened with a mild detergent solution.

3 DVB-S Receiver

SAFETY PRECAUTION

Attachments: Never add any attachments and/or equipment without the manufac-

turer consent; as such additions may result in the risk of ﬁ re, electric shock or other

personal injury.

Locating: Slots and openings in the cabinet are provided for ventilation to protect it

from overheating. Do not block these openings or allow them to be blocked by placing

the STB on a bed, sofa or other similar surface, nor should it be placed over a radiator

or heat register

Power-Cord Protection: Place the power-supply cord out of the way, where it will not

be walked on. Please take special attentions to cords at plugs, convenience recepta-

cles and the point where they exit from the unit.

Object and Liquid Entry: Never put objects of any kind into this STB through openings,

as they may touch dangerous voltage points or short-out parts that could result in a

ﬁ re or electric shock. Never spill any liquid on the STB.

Note: Moisture may be formed inside the unit in the following conditions: When the

unit is suddenly moved from a cold environment or an air-condition room to a warm

place.

Immediately after a heater has been turned on. In a steamy or very humid room. If the

moisture forms inside the unit, it may not operate properly. To correct this problem,

turn on the power and wait about two hours for the moisture to evaporate.

Parts Replacement: When the unit parts need to be replaced, user should make sure

the service technician use the replacement parts speciﬁ ed by the manufacturer or

having the same characteristics as the original part. Unauthorized replacement may

put the unit in the risk of ﬁ re, electric shock or other hazards.

Safety Check: After all the maintenances and repairs are done, user is required to

request the service technician to conduct the overall safety check to ensure the ma-

chine is in the proper condition.

Installation Guide

1. REMOTE CONTROL & PANEL DESCRIPTION .............................................. 7

1.1 Front Panel Description .......................................................................................................... 7

1.2 Rear Panel Description ........................................................................................................... 8

1.3 Remote Control Description ................................................................................................ 9

2. BASIC OPERATIONS ............................................................................................. 10

2.1 Switch on STB ............................................................................................................................ 10

2.2 Standby-Modus .......................................................................................................................... 10

2.3 TV/Radio .................................................................................................................................... 10

2.4 Code .............................................................................................................................................. 11

2.5 Mute ............................................................................................................................................... 11

2.6 Channel Numberr ..................................................................................................................... 11

2.7 INFO ................................................................................................................................................ 11

2.8 MULTI-PIC ..................................................................................................................................... 11

2.9 FAV .................................................................................................................................................. 12

2.10 PGUP / PGDN ........................................................................................................................... 12

2.11 BACK .............................................................................................................................................. 12

2.12 EPG ................................................................................................................................................. 13

2.13 FAV +/- .......................................................................................................................................... 14

2.14 Menü .............................................................................................................................................. 14

2.15 Exit ................................................................................................................................................... 14

2.16 CH ........................................................................................................................................ 14

2.17 Vol ............................................................................................................................................. 14

2.18 OK .................................................................................................................................................... 14

2.19 PIP (Picture in Picture) ........................................................................................................... 15

2.20 PVR-LISTE ..................................................................................................................................... 15

2.21 Audio .............................................................................................................................................. 16

2.22 Zoom ...............................................................................................................................................16

2.23 SUBT ...............................................................................................................................................16

2.24 TXT ...................................................................................................................................................16

2.25 PAUSE .............................................................................................................................................17

2.26 A-B ....................................................................................................................................................17

2.27 T.S. ....................................................................................................................................................17

2.28 Goto .................................................................................................................................................17

2.29 ........................................................................................................................................................17

2.30 ........................................................................................................................................................18

2.31 ................................................................................................................................................18

2.32 .......................................................................................................................................................18

2.33 ......................................................................................................................................................18

2.34 ..............................................................................................................................................18

2.35 LNB Short .....................................................................................................................................18

CONTENTS

5 DVB-S Receiver

3. CHANNEL .................................................................................................................. 19

3.1 TV Channel List ...........................................................................................................................19

3.1.1 Favorite .............................................................................................................................. 20

3.1.2 Move .................................................................................................................................. 20

3.1.3 Sort .....................................................................................................................................21

3.1.4 Edit .......................................................................................................................................21

3.1.5 Find ..................................................................................................................................... 23

3.2 Radio Channel List .................................................................................................................... 23

3.3 Channel Setup ............................................................................................................................ 23

3.4 Favorite group list name ........................................................................................................24

3.5 Delete All .......................................................................................................................................24

3.6 Restore channel list and settings ......................................................................................24

3.7 Save channel list and settings ............................................................................................ 25

4. INSTALLATION ....................................................................................................... 26

4.1 Single Search ............................................................................................................................. 26

4.2 Multi Search ............................................................................................................................... 28

4.3 TP Scan ......................................................................................................................................... 28

4.4 Satellite List ................................................................................................................................. 30

4.5 TP List .............................................................................................................................................31

4.6 Satellite Guide ............................................................................................................................ 32

5. SYSTEM SETUP .......................................................................................................33

5.1 Language ...................................................................................................................................... 33

5.2 TV System.....................................................................................................................................34

5.3 Time & Timer Setting ...............................................................................................................34

5.4 OSD Setting ................................................................................................................................. 36

5.5 Parental Lock ..............................................................................................................................37

5.6 Power setting ............................................................................................................................. 38

6. TOOLS ..........................................................................................................................39

6.1 Information .................................................................................................................................. 39

6.2 Quick Setup ................................................................................................................................. 39

6.3 Game .............................................................................................................................................. 40

6.4 Factory Default .......................................................................................................................... 42

6.5 Software Upgrade .................................................................................................................. 42

6.5.1 Software Upgrade ..................................................................................................... 42

6.5.2 Upgrade by Satellite................................................................................................... 43

6.5.3 Upgrade .......................................................................................................................... 43

6.6 SatcoDX Auto Programming ..............................................................................................44

CONTENTS

Installation Guide

7. MEDIA MANAGEMENT ..........................................................................................45

7.1 Media-List ..................................................................................................................................... 45

7.1.1 All ............................................................................................................................................ 46

7.1.2 MP3 ..................................................................................................................................... 48

7.1.3 Image ................................................................................................................................... 49

7.1.4 Video .................................................................................................................................... 49

7.1.5 Music List .......................................................................................................................... 49

7.1.6 Picture List ........................................................................................................................ 50

7.1.7 Video list ............................................................................................................................. 50

7.1.8 Record list ......................................................................................................................... 50

7.2 Media Control ............................................................................................................................. 52

7.3 Disk Information ........................................................................................................................ 52

7.4 Upgrade ........................................................................................................................................ 52

8. TECHNICAL SPECIFICATION ................................................................................53

CONTENTS

7 DVB-S Receiver

1. REMOTE CONTROL & PANEL DESCRIPTION

1.1 Front Panel Description

No Key Description

1 Display Displays the received channel number while operating

(4-Digit/7-Segment) and time while in standby mode.

2 POWER Is used to switch between the working mode and the

standby mode.

3 VOL+/- To change volume to move cursor,

change numbers in

the menu or to change the choice

4 MENU To enter into the main menu and

exit all menus.

5 OK To select an item in the menu and conﬁ rm

it or pop up channel list when no menu.

6 CH+/- To change channels or for navigating and changing

values in menus.

7 Remote Sensor Detects the infrared signals from the remote control

unit.

2 3 546

1 7

Installation Guide

1. REMOTE CONTROL & PANEL DESCRIPTION

1.2 Rear Panel Description

No Key Description

1 TV SCART Output SCART for the connection to a TV set.

2 IF IN Satellite input.

3 IF OUT Satellite output for cascading to other devices

Note: The operation of another receiver at the same

time is only possible with limited channel selection.

4 AUDIO HiFi outputs for stereo set

5 VIDEO CVBS video output for TV AV in.

6 S/PDIF Digital output for Dolby Digital.

7 USB USB-Port for record and replay from extrem media

8 AC IN Mains input cable.

9 POWER ON/OFF Allows to completely switch off the receiver.

9 DVB-S Receiver

1. REMOTE CONTROL & PANEL DESCRIPTION

1.3 Remote Control Description

Installation Guide

2.1 Switch on STB

Switch the [Device’s Main Power] switch on.

When the STB is ﬁ rst used it will display “Quick Setup” window. you will set Language,

First Audio, Second Audio, LNB Power, Antenna Setup and Multi Search.

? Frequently Asked Question

Q: The power of my STB is on and it is running in TV mode but the TV screen shows

nothing:

A: Make sure the TV set has been set to the correct video input(not the TV

channels). For example, if you have connected the unit to the video1 input of the

TV set then you need to select the corresponding input of the TV. Mostly it is

done with the AV button of the TVs remote control unit.

Q: My STB is running in TV mode but the TV screen shows nothing except one ball

and “No Signal”.

A: That means the channel you selected has no signal. This can be caused by several

reasons:

1. The channel you selected is not from the satellite to which your dish is pointing. Select

another channel.

2. The signal of current TV channel is too weak. You can try to change to other channels

with a stronger signal. If the problems still exist, please consult your local dealer or

installer for technical service.

3. You selected the wrong LNB type in the installation menu or your DiSEqC switch

conﬁ guration is not correct.

2.2 Standby Mode

1. Press [Power] button to switch from TV/radio mode to standby mode

2. In standby mode press [Power] button again to switch back to TV/radio mode. The

last active channel will be showed.

3. To switch off the STB complete press the main power button.

2.3 TV/Radio

In TV mode, press [TV/Radio] to switch to Radio mode. In Radio mode press

[TV/Radio] again to switch back to TV mode.

2. BASIC OPERATIONS

11 DVB-S Receiver

2. BASIC OPERATIONS

2.4 Code

For this, press the button CODE on your re-

mote control until the correct LED is lighting.

2.5 Mute

1. Press the [Mute] button to mute the sound. On the screen an icon will be displayed

to indicate the muted sound.

2. Press the [Mute] button again to restore the sound.

2.6 Channel Number

In TV mode you can enter the channel number directly with your remote control unit and

conﬁ rm the number with the OK button to change to the desired channel.

2.7 INFO

In TV mode, press [INFO] button can open

information screen, in the window shows the

parameters of current channel.

Two dynamic bars at the bottom of the

window reﬂ ect the signal intensity and signal

quality of the current channel.

Installation Guide

2.8 MULTI-PIC

In TV mode, press [0] key to enter the

“MULTI-PIC” menu.

1. In “MULTI-PIC” menu, you can choose

channels’ preview window(static), starting

from the current channel. Only the

marked preview program is continuously

playing.

2. Press [CH

] / [Vol ] to change

the marked channel among the preview

programs.

3. With the number buttons [1] ~ [9] you can directly move the highlight to the related

channel.

4. With [OK] you return to full screen mode in the marked channel.

2.9 FAV

1. In TV mode press the [FAV] button to

display the Favorite Group window on the

screen as the picture beside shows.

2. In the Favorite Group window you can

select the desired favorite channel with

[CH ] and conﬁ rm it with [OK] to

switch to it. In bigger groups you can

navigate with [PGUP/ PGDN].

3. With [Vol ]. You can select different

Favorite Groups.

4. Press [Exit] to close the Favorite Group window.

? Frequently Asked Question

Q: Why the screen displays “No Favorite Channel” after pressing the [Favorite] but-

ton?

A: No channels have been assigned to a Favorite Group yet. You can do this in the chan-

nel menu..

2.10 PGUP / PGDN

Drücken Sie im TV-Modus [PGUP/PGDN], um direkt zwischen Satelliten umzuschalten.

2. BASIC OPERATIONS

13 DVB-S Receiver

2.11 BACK

Pressing the [BACK] button allows you to toggle between the actual and the last se-

lected channel

2.12 EPG

1. The STB supports Electronic Program

Guides (EPG) to give you information

about the actual programs of certain

channels like event name, subtitle,

description, start and ﬁ nish time. This

feature is depending on the service of the

channel provider.

Press [EPG] to open the EPG window.

2. The [Red] button opens the detailed

schedule of the marked channel. You

can select an event with [CH ] and

display the event’s detailed description

with [OK].

3. Press the [Green] button in the EPG menu

to display the detailed information of the

actual event in the selected channel. With

the [Yellow] button you can program a

timer with the start and ﬁ nish time and

date of this event.

4. Press the [Yellow] button in the EPG

menu to program a timer with the actual

events data.

5. To close the EPG menu press [Exit].

2. BASIC OPERATIONS

Installation Guide

2.13 FAV +/-

1. In full screen, press [FAV +/-] keys can switch the favorite channels in current satel-

lite channels list directly.

2. The sequence of the switch favorite channels is following the sequence that in the

current satellite channel list, not follow the sequence in the favorite group.

2.14 Menu

Press [Menu] button to enter or exit the current menu.

2.15 Exit

Press [Exit] button to exit the current menu.

2.16 CH

In TV/Radio mode press [CH ] to change channel.

2.17 Vol

In TV/Radio mode, press [Vol ] to adjust volume.

2.18 OK

1. In TV mode press [OK] button to open the

Channel List window.

2. Press the [Red] exchange screen.

3. Press [Green] button to sort the channels

by free and scrambled channels. Free

channel are listed ﬁ rst and scrambled

channels last aufgeführt.

2. BASIC OPERATIONS

15 DVB-S Receiver

4. Press [Yellow] button to open the SAT

list. After selecting a satellite the channel

list will be reduced to the channels of this

satellite.

5. Press [FAV] button to open FAV list. After

selecting a Favorite Group the channel

list will be reduced to the channels of this

group.

6. Press [Blue] button to open the Find

window. You can use this feature to ﬁ nd

channel by their names.

7. Press [OK] to change and display the marked channel.

2.19 PIP (Picture in Picture)

In TV mode, press [PIP] button allows you to

watch two channels from the same trans-

ponder at the same time.

1. Swap: press red [Swap] button to

exchange the two watching channels in big

picture size and smaller picture size.

2. Move: press green [Move] button to move

the smaller size picture to the desired

position.

3. List: press yellow [List] to show all the

available channels of smaller picture.

4. Size: press blue [size] button to zoom-in or

zoom out the smaller picture.

2.20 PVR LIST

In TV mode, press [PVR LIST] button to access directly to the “Record List” menu

2. BASIC OPERATIONS

Installation Guide

2.21 Audio

1. In TV mode, press the [Audio] button to

open the Audio Mode window.

2. Select the item you want to adjust with

[CH

] and change the value with

[Vol ].

2.22 Zoom

1. The [Zoom] key allows you to magnify

a certain area on the images and the

current screen will show

2. Press [Zoom] key again, the image will

enlarge rotate as x1, x2, x4, x6, x8, x12,

x16.

3. In “x2

x16” image, using [CH ] /

[Vol ] keys to move the image center

area you want to see.

4. In zoom mode, press [Exit] to close

“Zoom” window.

2.23 SUB

Sub (Subtitle): In “OSD Setting”menu, use [SUB] to select “standard” or “Off”. If the

current channel has subtitle information, it will be displayed if this function is “On”.

If this function is “Off” subtitles won’t be displayed.

2.24 TTX

1. Press [TTX] button in TV mode to

open the teletext page. This service is

depending on the support of the channel

provider.

2. If the channel does not support teletext

information, it will show “No Teletext Data”

on the screen.

2. BASIC OPERATIONS

17 DVB-S Receiver

2.25 PAUSE

1. In playing mode, press [PAUSE], the picture will be paused, but the sound of the chan-

nel will still continues.

2. Press [PAUSE] again, the screen’s picture will skip over to the current playing picture,

and the sound of the channel will corresponding playing.

2.26 A-B

In recorded mode, during your watching,

press [A-B] button to set up a starting point

A, then set another point B by press [A-B]

button again after a while, then it will start

to playback from A to B and repeat the

programs between this two points if no any

interruption.

2.27 T.S.

In TV mode, press [T.S.] button you will be asked to “Do you want to time shift?” menu.

2.28 Goto

When you play the recorded channels, press [Goto] button, the “Jump to” message box

will pop up, input the Time and press [OK], then the receiver will back to the input time

point and play the program from that point continually. (If the input time is more than the

recorded time, the picture will back to last picture, please noted.)

2.29

When you play a recorded program, press

[ ] button will stop the recorded channel

playing and back to the Record Management

menu. When you are recording a program,

press [ ] button you will be asked to “Do you

want to stop record?” menu.

2. BASIC OPERATIONS

Installation Guide

2.30

In TV mode, press [ ] button you will be

asked to “Do you want to record?” menu.

2.31

When you play a recorded channel, press

[ ] button to back the program fast and Press [ ] to fast forward the program.

Selection: 2x, 4x, 8x speed .

2.32

When you play a current or recorded program, press [ ] will stop the program, press

[ ] again will play the program continually, And Timeshift is started by this key.

2.33

Press [ ] button when you play a marked program, the screen will record to the an

mark point.

2.34

Press [ ] button when you play a marked program, the screen will jump to the next

mark point.

1. Jump Step Value: “1 Mins / 3 Mins /5 Mins / 10 Mins / 15 Mins” jump.

2. Jump Step Value: Record the an mark point.

2.35 LNB Short

When LNB is short, it will notify user on screen “LNB Short!” Please check your cables

and connections for shorts. When the short is removed the warning message will

disappear.

2. BASIC OPERATIONS

19 DVB-S Receiver

Press [Menu] in the TV/radio mode to enter

the main menu.

1. Press [CH

] to select the channel

item.

2. Press [OK] to enter the selected item.

In the channel menu:

Press[CH

] to select the wanted menu

item among TV Channel List, Radio Channel

List, Channel setup, Favorite group list name,

Delete All, Restore channel list and settings

and Save channel list and settings.

Press [OK] to enter the selected item.

3.1 TV Channel List

If you enter the channel list menu a window

like the one below will open.

1. You can move the highlighted channel

with[CH ] and press [OK] to preview

the highlighted program in the preview

window.

2. Press [PGUP/PGDN] on the RCU to jump

between the channels by pages.

3. Press [Vol ] to switch satellite of the

program group.

4. Press [Menu] or [Exit] buttons to enter

TV playing mode.

5. The color buttons offer further functions

to manage the channel list.

3. CHANNEL

Installation Guide

3.1.1 Favorite

1. Press [FAV] to open the favorite window.

2. You can select between 8 favorite groups

with[CH ] Press [OK] to assign the

channel to a favorite group, press [EXIT]

to exit favorite group.

3. Press [OK] again to remove the channel

from the marked favorite group.

4. Press [MENU] button you will be asked

“Are you sure to save?”. Select “Yes” to

save the marked favorite group. Select

“No” to cancel the operation.

5. To return to the TV channel list. The channels of favorite groups are indicated with a

favorite icon behind the name.

3.1.2 Move

Pressing the [Red] button in the TV channel

list will open another window where you can

choose between move the actual channel

and swap the actual channel to the desired

position, press [OK] to conﬁ rm it.

a) Move

1. Press [Red] button to show a moving

icon behind the channel name.

2. Move the channel to the desired position with [CH ]. Press [OK] to conﬁ rm the

position.

b) Swap

1. Press [Green] button to show a moving icon behind the channel name.

2. Move the channel to the desired position with [CH ] Press [OK], then the

selected channel will exchange the postions with the channel name on this position

immediately.

3. CHANNEL

21 DVB-S Receiver

3.1.3 Sort

Press [Green] to open the sort window.

Press [CH

] to select and [OK] to

conﬁ rm your choice.

The ways of sorting are:

• Default: Sort channel factory default.

• FTA/CAS: Sort channel by free and

scrambled sequence. Free channels will

be listed ﬁ rst and scrambled channels

behind in the channel list.

• Lock: Unlocked channels are listed ﬁ rst end locked channels at the end.

• Name(A-Z): Sorting in Alphabetical order, ignoring “$” symbol.

• Name(Z-A): Sorting in Alphabetical order, ignoring “$” symbol.

3.1.4 Edit

After pressing the [Yellow] button a window

for entering the password will open. The

default password is “0000”.

You can delete, skip, lock and edit the chan-

nel.

Press [MENU] to leave the channel editing.

The system will ask you to conﬁ rm the saving

of the changes you made.

3.1.4.1 Delete

In channel edit menu press [Red] button will open another window where you can

choose between delete one channel and delete all channel.

• Del One

Press [Red] button to mark a channel for deleting. Marked channel will be deleted

after you conﬁ rm to save the changes when you leave this menu.

• Del All

a) Press [Green] button to show a deleting icon behind all channel name.

b) Press [MENU] button you will be asked “Are you sure to save?”. Select “OK” to delete

all channel. Select “Cancel” to cancel the operation.

3.1.4.2 Skip

In channel edit menu, press [Green] button to place a skip icon behind the name of the

highlighted channel. Marked channels will be skipped when you change channels in TV

mode after you conﬁ rm to save the changes when you leave this menu.

3.1.4.3 Lock

In channel edit menu, press [Yellow] button to place a lock icon behind the name of the

highlighted channel. Marked channels will be locked and displayed only after password

has been entered if you conﬁ rm to save the changes when you leave this menu.

3. CHANNEL

Installation Guide

3.1.4.4 Edit

Pressing the [Blue] button in the TV chan-

nel list edit menu will open another window

where you can choose between edit the

actual channel and create a new channel.

• Edit

Press [Red] button to edit the channel.

1. Selecting the name item with [OK] will

display a button pad to show you how to

edit the channel name.

2. On the “Video PID”, “Audio PID” and “PCR

PID” items you can input numbers to

modify the item’s value.

3. After modiﬁ cation select “Save” and

press [OK] button to save the modiﬁ ed

values and exit “Edit” mode. Or select “Exit”

and press [OK] to leave edit mode without

saving the modiﬁ cations

• Create

Press [Green] button to open the create

channel window.

1. Press [OK] on the “Satellite” item to

display the satellite list. You can select the

satellite for which you want to create a

new channel.

2. With marked “TP Index” item press [OK]

to display TP list, use[CH ] to select

for which you want to create a new chan-

nel. Press [OK] to display the TP number

where the channel can be found. The next

three items will show the related param-

eters.

3. Highlight the “Name” item and press [OK] to display the button pad and edit the new

channel’s name. In “Video PID”, “Audio PID” and “PCR PID” items you can enter the

numbers directly to set these parameters of the new channel.

4. After modiﬁ cation select “Save” and press [OK] to save the new channel and leave

the edit mode. Select “Exit” and press [OK] to exit the edit mode without saving the

new channel.

3. CHANNEL

23 DVB-S Receiver

3.1.5 Find

1. Press [Blue] button to open the “Find”

window like showed beside. Press

[CH ] /[Vol ] to select the leading

character of the channel name and press

[OK] to conﬁ rm it.

2. After entering the character(s) highlight

“OK” in the window and press [OK] on the

RCU.

3. Press [Exit] button to close the ﬁ nd window and brings you back to the channel list.

3.2 Radio Channel List

Basically the operation of “Radio Channel List” is same as “TV Channel List”, except that

in the small channel window the radio Logo will be displayed.

3.3 Channel Setup

When you enter the “Channel Setup” menu

you will see a screen like beside:

1. Startup Channel: Press [OK] to enter

“Startup Channel” menu to see the screen

like showed beside

• If you set of “Boot on Channel” to “On”

you can edit the following two items. If

the setting is “Off” the box always starts

with the channel that was running when

the box has been switched off.

• On the “Mode” item you can select

either “TV channel” or “Radio channel”.

• On “Startup Channel” item you can open

the channel list by pressing [OK]. Then

you can select the channel of you

choice. Press [OK] again to conﬁ rm.

2. Channel Play type: Use [CH ] to

select, press [OK] to enter “Channel Play

Type” menu. Here you can select the “play-

ing channels” as “All”, “Free” or “Scram-

bled” with [Vol ]

3. If you select “Free” then all scrambled

channels will be skipped when you change

channels with [Vol ]

4. Press [Exit] to leave the “Channel Setup”

menu.

3. CHANNEL

Installation Guide

3.4 Favorite group list name

When you enter “Favorite group list name”

menu with 8 favorite group will be

displayed, press [OK] on the RCU to rename

favorite group. Use [CH

] /[Vol ] to

select character, press [OK] to conﬁ rm it.

After modiﬁ cation select “OK” of button bar

and press [OK] on the RCU to rename the

favorite group name and leave the edit mode.

Press [Exit] on the RCU to exit the edit mode

without saving the favorite group name.

3.5 Delete All

To delete all channels:

1. Enter the password. The default password

is “0000”.

2. After entering the password correct a

safety question will show up where you

have to conﬁ rm ﬁ rst

3. Select “OK” to delete all channels or

“Cancel” to cancel the operation and con-

ﬁ rm with [OK].

4. In step 1 and step 2, pressing [Menu] will

exit the function directly without saving.

? Frequently Asked Question

Q: IF I incautiously delete all channels, what should I do?

A: there are two ways to restore:

To research all channels in the “Installation” menu.

Use “Factory Default” function to restore all channels in the “Tools” menu.

3. CHANNEL

25 DVB-S Receiver

3.6 Restore channel list and settings

To restore channel list and settings.

1. Enter the password. The default password

is “0000”.

2. After entering the password correct a

safety question will show up where you

have to conﬁ rm ﬁ rst.

3. Select “OK”, press [OK] to restore the last

backup channel list, the current channel

list will be erased. Select “Cancel” press

[OK] to cancel the operation.

3.7 Save channel list and settings

To save channel list and settings.

1. Enter the password. The default password

is “0000”.

2. After entering the password correct a

safety question will show up where you

have to conﬁ rm ﬁ rst.

3. Select “OK”, press [OK] to save current

channel list to backup channel list. Select

“Cancel” press [OK] to cancel the opera-

tion

3. CHANNEL

Installation Guide

After selecting the installation menu you can

see the window like beside.

In “Installation” menu;

1. Press [CH ] to select menu items

among Single Search, Multi Search, TP

Scan, Satellite List, TP List and Satellite

Guide.

2. Press [OK] to enter the selected item.

4.1 Single Search

After selecting “Single Search” you will see a

window like beside:

1. In the “Satellite” item press[Vol ] to se-

lect the satellite which you want to scan

or press [OK] to open the “satellite list” to

select directly with [CH ] , press [OK]

to conﬁ rm it.

2. LNB Conﬁ guration: Press [OK] to enter

LNB conﬁ guration, you will see a window

like beside:

LNB Type: Press [Vol ]

to switch among “Standard”, “User” and

“Universal” mode.

For Example: If you use a Dual LNB, then

you should select “User” option in “LNB

Type” and set the correct frequency in

LNB type.

22K:

Use [Vol ] to switch “ON” and “Off”. The

22KHz signal is used in KU universal LNBs

to change between low band and high

band..

4. INSTALLATION

27 DVB-S Receiver

! Notice:

After choosing LNB type “Universal” you cannot modify 22K.

DiSEqC1.0:

Use [Vol ] to switch the options or press [OK] to open the DiSEqC1.0 option list to

select directly with [CH ] , press [OK] to conﬁ rm it.

DiSEqC1.1:

Use [Vol ] to switch DiSEqC1.1 option or press [OK] to enter DiSEqC1.1 option to

select directly with [CH ] , press [OK] to conﬁ rm it. The options of this item are:

Disable / CCard1 M1 Port1 / CCard1 M1 Port2 / CCard1 M1 Port3 / CCard1

M1 Port4 / CCard1 M2 Port1 / CCard1 M2 Port2 / CCard1 M2 Port3 / CCard1

M2 Port4 / CCard1 M3 Port1 / CCard1 M3 Port2 / CCard1 M3 Port3 / CCard1

M3 Port4 / CCard2 Port1 / CCard2 Port2 / CCard2 Port3 / CCard2 Port4 /

CCard2 Port5 / CCard2 Port6 / CCard2 Port7 / CCard2 Port8 / CCard2 Port9

/ CCard2 Port10 / CCard2 Port11 / CCard2 Port12 / CCard2 Port13 / CCard2

Port14 / CCard2 Port15 / CCard2 Port16.

Positioner:

Press [Vol ] to select between “Off / DiSEqC1.2 / USALS”.

! Notice:

When you select “DiSEqC1.2 or USALS”, “DiSEqC1.0” and “DiSEqC1.1” items will be

disabled.

Polarity:

Press [Vol ] to switch between “Auto / H / V ”.

Toneburst:

Press [Vol ] to switch this function “On” or “Off”.

3. DiSEqC1.0 4Port: Use [Vol ] to switch the options of DiSEqC1.0. Between Disable /

LNB1 / LNB2 / LNB3 / LNB4.

4. TP Index: Use [Vol ] to select the desired transponder or press [OK] to open the

TP list to select directly with [CH ] , press [OK] again to display the TP number

where the channel can be found.

5. FTA Only: Press [Vol ] to select to scan only free channels or even scrambled chan-

nels. If you select “Yes” it will scan free channels only.

6. Scan Channel: Press [Vol ] to select to scan TV + radio channels, or just TV chan-

nels or just radio channels.

7. Scan Mode: You can select “Auto Scan”, “Preset Scan” or “NIT Search” to blind scan

preset transponders or network transponders of the selected satellite.

8. Search: Press [OK] to start scanning. In the lower part of the window the progress of

scanning and the found channels are displayed.

4. INSTALLATION

Installation Guide

4.2 Multi Search

When you enter the “Multi Search” menu a

window like the one beside will open.

1. In the “Satellite” item press [Vol

] to

select the satellite which you want to scan

or press [OK] to open the “satellite list” to

select directly with [CH ] , and press

[OK] to mark/unmark and [MENU] to

ﬁ nish the selection. You can select several

satellites in this menu. The system will

use DiSEqC1.0/1.1, DiSEqC1.2 and USALS

functions to search the marked satellites

and scan channels.

2. On “FTA Only” item, press [Vol ] to select scanning of all channels or just scanning

of free channels. If you select “Yes”, it will scan free channels only.

3. On “Scan Channel” item, press [Vol ] to select the scanning range from TV + radio

channels, only TV channels or only radio channels.

4. On “Scan Mode” item, you can select “Auto Scan”, “Preset Scan” or “NIT Search” to

blind scan preset transponders or network transponders of the selected satellite.

5. Select “Search” and press [OK] to start scanning. In the lower part of the window the

progress of scanning and the found channels are displayed.

6. Press [Menu/Exit] to cancel or ﬁ nish the scanning and saving the found channels.

4.3 TP Scan

When you enter “TP Scan” menu a window

like the one beside will be displayed.

1. In the “Satellite” item press [Vol ] to

select the satellite which you want to scan

or press [OK] to open the “satellite list” to

select directly with [CH ] , press [OK]

to conﬁ rm it.

2. TP Index: Use [Vol ] to select the

desired transponder or press [OK] to

open the TP list to select directly with

[CH ], press [OK] again to display

the TP number where the channel can be

found. Press [Red / Green / Yellow] key

on the RCU for the related functions.

4. INSTALLATION

29 DVB-S Receiver

• When you press [Red] it will display “New TP” in “TP Index” item. You have to set the

parameters of “TP Frequency”, “Symbol Rate” for this new transponder. Therefore

use the number buttons of the RCU. The available range are “3000~13450MHz” and

“1000~45000KS/s”.

• When you press [Green] a safety question will be displayed for conﬁ rmation to delete

the current transponder or not. If you select “OK”, the current transponder will be

deleted and the total number of transponders will be reduced.

• When you press [Yellow] a safety question will be displayed for conﬁ rmation to delete

all transponders or not. If you select “OK”, the all transponders on current satellite will

be deleted.

3. For existing transponders you also can use number buttons to modify the param-

eters of “TP Frequency” and “Symbol Rate” or [Vol ] to change the value directly.

“Polarity” and “FTA only” are used for setting scans conditions. Press [Vol ] to

select a different mode.

On “TP Scan” item, press [OK] will open another window where you can set “Scan

Mode”, “Program Type” and “NIT Search”. Press [Menu/Exit] to return to the

previous menu.

Press [Red] button to add a new TP.

Press [Green] button to delete the current TP.

Press [Yellow] button to delete all transponders on current satellite

4. Antenna Setup: Press [OK] to enter LNB

conﬁ guration, you will see a window like

beside:

LNB Type:

Press [Vol ] to switch among “Stand-

ard”, “User” and “Universal” mode.

For Example: If you use a Dual LNB, then

you should select “User” option in “LNB

Type” and set the correct frequency in

LNB type.

22K: Use [Vol ] to switch “ON” and “Off”. The 22KHz signal is used in KU universal

LNBs to change between low band and high band.

! Notice:

After choosing LNB type “Universal” you cannot modify 22K.

DiSEqC1.0:

Use [Vol ] to switch the options or press [OK] to open the DiSEqC1.0 option list to

select directly with[CH ] , press [OK] to conﬁ rm it.

4. INSTALLATION

Installation Guide

DiSEqC1.1:

Use [Vol ] to switch DiSEqC1.1 option or press [OK] to enter DiSEqC1.1 option to

select directly with [CH

], press [OK] to conﬁ rm it. The options of this item are:

Disable / CCard1 M1 Port1 / CCard1 M1 Port2 / CCard1 M1 Port3 / CCard1

M1 Port4 / CCard1 M2 Port1 / CCard1 M2 Port2 / CCard1 M2 Port3 / CCard1

M2 Port4 / CCard1 M3 Port1 / CCard1 M3 Port2 / CCard1 M3 Port3 / CCard1

M3 Port4 / CCard2 Port1 / CCard2 Port2 / CCard2 Port3 / CCard2 Port4 /

CCard2 Port5 / CCard2 Port6 / CCard2 Port7 / CCard2 Port8 / CCard2 Port9

/ CCard2 Port10 / CCard2 Port11 / CCard2 Port12 / CCard2 Port13 / CCard2

Port14 / CCard2 Port15 / CCard2 Port16.

Positioner:

Press [Vol

] to select between “Off / DiSEqC1.2 / USALS”.

! Notice:

When you select “DiSEqC1.2 or USALS”, “DiSEqC1.0” and “DiSEqC1.1” items will be

disabled.

Polarity:

Press [Vol ] to switch between “Auto / H / V ”.

Toneburst:

Press [Vol ] to switch this function “On” or “Off”.

5. After you completed your modiﬁ cation, on the “TP Scan” item, press [OK] twice to

start scanning.

4.4 Satellite List

When you enter the “Satellite List” menu you

can see a window like the one beside:

1. Press [Red] button to enter edit satellite

menu. You can edit the satellite’s name

and its longitude.

4. INSTALLATION

31 DVB-S Receiver

2. Press [Green] button to open the “Add

satellite” window.

3. After pressing [Yellow] button you will be

asked “Are you sure to delete?”. Select

“OK” to delete the marked satellite. Select

“Cancel” to cancel the operation.

4.5 TP List

When you open the “TP List” menu you will

see a window like the one beside.

1. Press [Vol ] to change the marked

satellite.

2. Press [Red] button to open the “Edit

TP” menu. Here you can edit the

transponder’s data.

3. Press [Green] button to open the “Add

TP” menu. Here you can add a new TP and

setup its parameters.

4. INSTALLATION

Installation Guide

4. Press [Yellow] button will open a dialog

box asking you to conﬁ rm the deletion

of the current TP. If you select “OK” all

the related channels will be deleted. If

you select “Cancel” the operation will be

cancelled.

5. Pressing the [Blue] button will open a

dialog box asking you to conﬁ rm the

deletion of all TP on current satellite. If you

select “OK”, all TP of the current satellite

will be deleted. If you select “Cancel” the

operation will be cancelled.

4.6 Satellite Guide

When you enter “Satellite Guide” menu, you

will see the screen like beside: Here you can

enter your local longitude and latitude and

the satellite’s longitude. The receiver calcu-

lates the antenna’s orientation and eleva-

tion to point your antenna to the selected

satellite.

1. Use the [Number] buttons to input

the values of “Local Longitude”, “Local

Latitude” and “Satellite Longitude”.

2. In the “Calculate” item press [OK], the

receiver auto calculates the antenna’s

orientation and elevation to point your

antenna to the selected satellite.

3. Press [Menu / Exit] to return to the previous menu.

4. INSTALLATION

33 DVB-S Receiver

When you open the “System Setup” menu a

window like the one beside will be opened.

In “System Setup” menu:

1. Press [CH ] to select menu items

among Language, TV System, Time &

Timer setting, OSD Setting, Parental Lock

and Power setting.

2. Press [OK] to open the selected item.

5.1 Language

After selecting the “Language” menu you will

see a window like beside:

1. Menu Language: Press [Vol ] to select

languages. The selection of language

include: English, German, French, Spanish,

Italian, Portuguese, Turkish, Polish,

Russian, Danish, Greek, Hungarian,

Arabic, Farsi and Dutch.

2. First Audio: Some channels offer more than one audio language. This function al-

lows you to set the preferred audio language for those channels. If a channel offers

the same audio language as the “First Audio” you set the system will play this audio

language as default. If the channel does not offer this audio language then the system

will compare the offered languages with the second audio language. The selections of

audio language include: English, German, French, Spanish, Italian, Portuguese, Turkish,

Polish, Russian, Danish, Greek, Hungarian, Arabic, Farsi and Dutch.

3. Second Audio: If the channel has no audio language that corresponds with “First

Audio” but with “Second Audio” the system will play the second audio language as

default. If no audio language corresponds with the “Second Audio” then the default

language of the current channel will be played instead. The selections of audio

language include: English, German, French, Spanish, Italian, Portuguese, Turkish,

Polish, Russian, Danish, Greek, Hungarian, Arabic, Farsi and Dutch.

4. Subtitle Language: In “OSD Setting”menu, use [Vol ] to select “On” or “Off”. If the

current channel has subtitle information, it will be displayed if this function is “On”. If

this function is “Off” subtitles won’t be displayed. The selections of subtitle language

include: English, German, French, Spanish, Italian, Portuguese, Turkish, Polish,

Russian, Danish, Greek, Hungarian, Arabic, Farsi and Dutch.

5. Teletext: Press [Text] button in TV mode to open the teletext page. This service is

depending on the support of the channel provider. If the channel does not support

teletext information, it will show “No Teletext Data” on the screen. The selections

of teletext language include: English, German, French, Spanish, Italian, Portuguese,

Turkish, Polish, Russian, Danish, Greek, Hungarian, Arabic, Farsi and Dutch.

6. Press [Menu/Exit] to return back from “Language” menu.

5. SYSTEM SETUP

Installation Guide

5.2 TV System

When you enter the “TV System” menu you

will see the screen like below:

1. Display Mode is used to switch the display

mode. You can select from Auto / PAL /

PAL-M / PAL-N / NTSC3.58 / NTSC4.43.

Press [Vol ] to switch the desired

mode.

2. Aspect Mode is used to switch the screen

aspect ratio mode. You can select the

needed mode from Auto / 4:3 PS / 4:3

LB / 16:9 with [Vol ].

3. Video output is use for switching the screen aspect ratio mode. Now we provide

below options: CVBS / CVBS + RGB / CVBS + S-Video. You can press [Vol ] key to

select each mode circularly.

4. RF System is use for switching the screen aspect ratio mode. Now we provide below

options: PAL-BG / PAL-I / PAL-DK / NTSC-M. You can press [Vol ] key to select

each mode circularly.

5. RF Channel is use for switching the screen aspect ratio mode. Now we provide below

options: 21-69. You can press [Vol ] key to select each mode circularly.

6. Press [Menu/Exit] to return to the previous menu.

5.3 Time & Timer Setting

When you enter “Time & Timer Setting” a

menu with this 3 items will be opened.

1. Timer: Select “Timer” item and press [OK]

to enter the “Timer” menu. You can press

[CH ] to select item.

• The current time will be displayed

in the ﬁ rst column. If the current time

is incorrect, please modify it with the

[Number] buttons.

• Timer Number: You can press

[Vol ] to switch the timer number.

There are totally 8 timers.

• Timer Mode: Select how often the timer

is running: Once, Daily, Weekly, Monthly

and Yearly, or switch the timer to off.

• Timer Service: Select between TV

Channel, Radio Channel and Message.

5. SYSTEM SETUP

35 DVB-S Receiver

• When you select “TV Channel / Radio Channel”(timer setting for channel

change and Wakeup channel / date) then you have further options you need

to set:

Wakeup Channel: Press [OK] to enter the channel list, and select the channel

you want to see with [CH

] press [OK] to conﬁ rm it.

Wakeup Date: Use number buttons to input your wakeup date.

On Time: Use number buttons to input your wakeup time. If date and time are

reached then no matter if the system is in standby mode or in playing mode, it

will automatically switch to the channel you set and start to play.

Duration: Here you can set the time you want to see or play this channel. When

the time is reached, whenever the system is in standby mode or playing a

channel, the system will automatically switch to the channel you select and

play the channel within the duration time you set. The minmum duration unit is

one minute. After the duration time, the system will automatically switch to

Standby mode.

• When you select “Message”(reminding message) option in “Timer Service” then

you can enter additional data:

Wakeup Message: Press [Vol ] to select the category

of the wakeup message from Birthday, Anniversary and General.

Wakeup Date: Use the [Number] buttons to input your wakeup date.

On Time: Use the [Number] buttons to input your wakeup time. If date and time

are reached, no matter if the system is in standby mode or in playing mode, it

wil automatically show a reminding message. The message will be displayed on

the screen until you press [Exit] to close it.

Duration: Here you can set the time you want to see or play this channel. When

the time is reached, whenever the system is in standby mode or playing a

channel, the system will automatically switch to the channel you select and play

the channel within the duration time you set. The minmum duration unit is one

minute. After the duration time, the system will automatically switch to Standby

mode.

• Press [Exit] to leave the “Timer” menu

2. Local Time Setting: When you select

“Local Time Setting” and press [OK] then

you will see a window like the one beside:

• GMT Usage: This item is used to set

the time by using the time signal from

the satellite. Press [Vol ], to

change the setting.

• The “GMT Offset” item is only available

when “GMT Usage” is set to “On”. Press

[Vol

], to set the “GMT Offset”

value. With every time you press the

button the time offset will be

increased/decreased by half an hour.

5. SYSTEM SETUP

Installation Guide

• Summer: Press [Vol ] to switch this function “On” or “Off”.

• “Date” and “Time” items are only available when the “GMT Usage” is set to “Off”.

Press [Vol

] to select one item and use number buttons to input time and date

directly.

• Time Display: Press [Vol

] to switch this function “On” or “Off”.

NOTE:

If the current channel provides the correct time information, you will see the

current time after you entered “Local Time Setting” menu. If the channel doesn’t

provide time information, you have to input the date and time information manually.

The most channels support the time signal.

• Press [Exit] to leave the “Time” menu.

3. Sleep Timer: Select “Sleep Timer” item and press [OK] to set the sleep timer. You will

see “Sleep timer OFF / Sleep timer 10 / Sleep timer 30 / Sleep timer 60 / Sleep

timer 90 / Sleep timer 120”.

If you set a sleep time, the system will change to standby mode after the chosen time

period.

5.4 OSD Setting

When you select “OSD Setting” you will see a

screen like beside:

1. Subtitle Display: Press [Vol ] to

select “Off”, “Standard” or “Teletext

Subtitle”. If the current channel has

subtitle information, it will be displayed

if this function is “Standard” or “Teletext

Subtitle”. If this function is “Off” subtitles

won’t be displayed.

2. OSD Timeout: This setting determines the duration the info window is displayed on

the screen when you change channels. Press [Vol ] to set the time between 1 to

10 seconds.

3. Position: Press [Vol ] select the position between top and bottom.

4. OSD Transparency: With this parameter you can set the transparency of the menus.

Press [Vol ] select the value between 10%, 20%, 30%, 40% and “Off”(means no

transparency function).

5. Load OSD Setting Default: If you want to reset your OSD settings to the default set-

tings then select this item and press [OK].

6. Press [Exit] button to leave the “OSD Setting” menu.

5. SYSTEM SETUP

37 DVB-S Receiver

5.5 Parental Lock

You can set a password for anyone who

wishes to operate the “Installation” menu.

You can also set the password to lock chan-

nels. Below you ﬁ nd how to set and change

the password.

1. On “Parental Lock” press [OK] to open

a dialogue box and input the password.

After you entered the correct password,

you will see a screen like beside:

2. Menu Lock: If Menu Lock is set to “Yes” then you need to enter the password every

time you want to open the menu. If set to “No” then you can open the menu without

entering the password ﬁ rst.

3. Channel Lock: If set to “Yes” then you need to enter the password before you can see

those channels which have been marked as locked channels in the channel menu. If

set to “No” then even those channels can be selected without entering the password

ﬁ r s t .

4. New Password: Here you can change the existing password. You should do this

after you set up the receiver the ﬁ rst time and every time when you think that your

password is known by unauthorized persons. To change the password enter the new

password in the “New Password” item and repeat the same one in the “Conﬁ rm Pass-

word” item. If the passwords are not identically then you will see a warning message.

If you entered the same new password in both ﬁ elds then you will see the message

“Saving Data, Please Wait…”. From now on you need to use the new password to

open locked menus or locked channels.

NOTE: The default password is 0000.

5. Press [Exit] to leave the “Parental Lock” menu.

5. SYSTEM SETUP

Installation Guide

5.6 Power setting

When you select this option, you will see a

screen like beside:

LNB Power: If your receiver is connected

to the LNB directly then you need to set

the LNB Power to “On”. If your receiver is

connected to a multi switch (SMATV signal

distribution system) then it may be that you

don’t need to provide the power to the LNB.

But since this is depending on the kind of

installed distribution system we recommend

you to contact your installer or to refer to

the user manual of this system to get the

correct information.

You also just can change this setting and

check if you still can receive the channels. If

the LNB Power is off and you still can see all

channels then we recommend this setting.

5. SYSTEM SETUP

39 DVB-S Receiver

When you enter to “Tools” menu, you will see

a screen like beside:

In “Tools” menu:

1. Press [CH ] to select the wanted

item among Information, Quick Setup,

Game, Factory Default, Software Upgrade,

SatcoDX Auto Programming Smart and

Smart Card.

2. Press [OK] to enter the selected item.

6.1 Information

1. When you select the “Information” menu

you will see a screen like beside. The

screen displays data about the current

channel.

2. Press [Exit] button to leave the

information display.

6.2 Quick Setup

When the STB is used, which need to repeat

set menu Language, First Audio, Second

Audio, LNB Power, Single Search and Multi

Search.

6. TOOLS

Installation Guide

6.3 Game

When you enter “Game” menu, you will

see three games include Tetris, Snake and

Othello.

Basic operation statement:

1. Tetris

Mark “Setup” and press [Vol ] to

select the level (speed).

Mark “Start” and press [OK] to start

the game.

Mark “Cancel” and press [OK] to leave

the game.

Play the game:

• Press [Vol ] to move the block left

or right

• Press [Channel Up] to rotate the

block clockwise

• Press [Channel Down] to drop the

block faster

• Press [OK] to Pause/Play the game

• Press [Exit] to leave the game and

return to the game menu.

6. TOOLS

41 DVB-S Receiver

2. Snake

Mark “Setup” and press [Vol ]

to select the level (speed).

Mark “Start” and press [OK] to start

the game.

Mark “Cancel” and press [OK] to leave

the game.

Play the game:

• Press [Vol ]/[CH ] to guide

the snake to the red blocks. Every

block you ate increases the length of

the snake. If the snake runs against a

wall or against itself then it dies.

• Press [OK] to Pause/Play the game

• Press [Exit] to quit the game and

return to the game menu.

3. Othello

Mark “Setup” and press [Vol ] to

select the game level(degree of

difﬁ culty).

Mark “Start” and press [OK] to start

the game.

Mark “Cancel” and press [OK] to leave

the game.

Play the game:

• Press [Vol ]/[CH ] to

position the round mark.

• Press [OK] to set your stone.

• Press [Exit] to quit the game and

return to the game menu.

6. TOOLS

Installation Guide

6.4 Factory Default

When you press [OK] on the “Factory

Default” item:

1. A dialogue box will occur where you need

to enter the password.

2. After you input the correct password a

warning message will be displayed like the

one beside.

3. If you select “Yes” then all changes you

made will be reset to default values. Make

sure you really want to do this!

4. Press [Exit] in both steps will close the

window without resetting the receiver.

6.5 Software Upgrade

When you enter to “Software Upgrade”

menu, you will see a screen like beside:

1. Press [CH ] to select the wanted

item among Software Upgrade and Up-

grade by Satellite.

2. Press [OK] to enter the selected item.

6.5.1 Software Upgrade

1. This function allows you to upgrade the

software of the receiver. This can be done

from PC to receiver or from a master

receiver to a slave receiver.

6. TOOLS

43 DVB-S Receiver

2. Connect master receiver or PC to the slave receiver via serial interface (0-Modem

cable). Enter the “Software Upgrade” menu of the master receiver and press

[Vol

] to change the upgrade mode. Upgrade modes include: All code / Main code

/ CAS-data / Script GUI / Radio Back / default DB / Userdb.

3. Switch on the slave receiver.

4. Mark “Start” on the master reeciver and press [OK] to start upgrade.

Wait until the display on the front panel shows “-END”. Then switch off the receiver

and on again. Now the new software is used.

5. Press [MENU] to save the setting without upgrade.

6.5.2 Upgrade by Satellite

This function can upgrade the software of

your receiver through data sent by a satellite.

At the moment we offer satellite updates

only through ASTRA1 and Hotbird satellites.

1. Select the satellite and TP or input the TP

value and download PID.

2. Then mark “Start” and press [Enter] to

begin the download of the upgrade. This

may need up to 60 minutes. Therefore we

suggest using of this function only if you

don’t intent to watch TV during this time

6.5.3 Upgrade

This option allows updating the software of

the receiver with the received data from a

USB memory device. To do it, connect a USB

memory device to the receiver and accede to

this menu option.

The last software version to be loaded must

be placed at the root path of your USB

device.

1. Update ﬁ le: Select with [Vol

], the name

of the ﬁ le to be choosed.

2. Select “Start” and press [OK]. An alert

message appears indicating not to take

out the memory device during the loading

process.

6. TOOLS

Installation Guide

3. Once the ﬁ le has been loaded, it requires the conformity to end the upgrading

process, writing into the receiver “Are you sure to burn ﬂ ash ?”. Press [OK] to up-

grade the receiver. In case during the reading of the ﬁ le, it is corrupted or it would be

a not appropriated for this model of receiver, an alert message would appear “Error

reading the USB disk”.

4. After pressing [OK] the receiver will write into the Flash memory, and it will reboot to

end the upgrading process.

NOTE:

1. USB Upgrade menu will be gray when no USB device is pluged.

2. The upgrade ﬁ le is the binary ﬁ le, *.bin. Only the ﬁ les, which extend name is bin,

would be displayed. User need put the upgrade ﬁ le under root of USB card.

6.6 SatcoDX Auto Programming

This function is using the tables of the SatcoDX websites to update your channel and

satellite lists. You need a special application which is available on

the CD-ROM of the Tele-Satellite magazine. Install this software on your PC ﬁ rst.

1. Start the SatcoDX application on your PC.

2. Select “SatcoDX Auto Programming” item from the “Tools” menu and press [OK].

The screen will show the message “OK to Proceed”.

3. Press [OK] again and you will see the message “Ready to Download”.

4. In the PC application set the Baud Rate to 115200 and start the download

procedure.

! Caution:

The new download channels will delete the original channels list. Please be careful

before using it.

6. TOOLS

45 DVB-S Receiver

7. MEDIA MANAGEMENT

When you enter to “Media Management”

menu, you will see a screen like beside:

In “Media Management” menu:

1. Press [CH

] to select the Media

List, Media Control, Disk Information and

Upgrade.

2. Press [OK] to enter the selected item.

7.1 Media List

Press [CH ] to select the wanted item

partition.

Press [Red] button to open the “Rename”

window like showed beside.

Press [CH ] /[Vol ], to select the

leading character of the channel name and

press [OK] to conﬁ rm it.

If you enter the Media List menu a window

like the one below will open.

1. Press [Vol ] select the all, mp3, image,

video, music list, picture list, video list,

Record list.

2. You can move the highlighted Record with

[CH ] to preview the highlighted

program in the preview window.

3. Press [PGUP/PGDN] on the RCU to jump

between the channels by pages.

4. Press [Menu] or [Exit] buttons to enter

TV playing mode.

5. The color buttons offer further functions

to manage.

Installation Guide

7. MEDIA MANAGEMENT

7.1.1 All

[Edit]

Press [Red] button to open the “Edit” window

like showed beside.

The color buttons offer further functions to

manage.

1. Rename

• Press [Red] button to open the “Rename”

window like showed beside. Press

[CH ] /[Vol ] to select the leading

character of the channel name and press

[OK] to conﬁ rm it.

• After entering the character(s) highlight

“OK” in the window and press [OK] on the

RCU.

• Press [Exit] button to close the ﬁ nd

window and brings you back to the Record

list.

2. Delete

In all edit menu press [Green] button will

open another window where you can choose

between delete one and delete all.

• Del One

Press [Red] button to mark a “mp3 /

image / video”for deleting. Marked “mp3

/ image / video” will be deleted after you

conﬁ rm to save the changes when you

leave this menu.

• Del All

a) Press [Green] button to show a deleting

icon behind all “mp3 / image / video”

name.

b) Press [MENU] button you will be asked

.“Are you sure to save?”. Select “OK” to

.delete all “mp3 / image / video”. Select

.“Cancel” to cancel the operation.

47 DVB-S Receiver

7. MEDIA MANAGEMENT

3. Move

• Press [Yellow] button to show a moving

icon behind the “mp3 / image / video /

folder” name.

• Move the “mp3 / image / video / folder”

to the desired folder list with [CH ] .

Press [OK] to conﬁ rm the position.

4. Folder

• Press [Blue] button to open the “New

Folder” window like showed beside. Press

[CH ] /[Vol ] to select the leading

character of the folder name and press

[OK] to conﬁ rm it.

• After entering the character(s) highlight

“OK” in the window and press [OK] on the

RCU.

• Press [Exit] button to close the ﬁ nd win-

dow and brings you back to the all list.

Add

In all menu press [Green] button will open

another window where you can choose be-

tween add one and add all.

• Add One

Press [Red] button to mark a “mp3 /

image / video”for add. Marked “mp3 / im-

age / video” will be add after you conﬁ rm

to save the changes when you leave this

menu.

• Add All

a) Press [Green] button to show a add icon behind all “mp3 / image / video”

name.

b) Press [MENU] button you will be asked “Are you sure to save?”. Select “OK”

to add all “mp3 / image / video”. Select “Cancel” to cancel the operation.

Installation Guide

Find

Press [Blue] button to open the “Find”

window like showed beside. Press

[CH ] /[Vol ] to select the leading

character of the channel name and press

[OK] to conﬁ rm it.

After entering the character(s) highlight “OK”

in the window and press [OK] on the RCU.

Press [Exit] button to close the ﬁ nd window

and brings you back to the all list.

play

The play offer further functions to manage.

If you enter the play menu a window like the

one below will open.

The color buttons offer further functions to

manage the channel list.

Red:

When you play music program, press [Red]

will stop the program, press [Red] again will

play the program continually.

Green:

When you play music program, press

[Green] button to back the program fast.

Yellow:

When you play music program, press

[Yellow] button to fast forward the program.

Blue:

Change play mode by [Blue] Key, and play

mode include: Sequential / Random / Single

repeat / all repeat.

Press [Exit] to return to the previous menu.

7.1.2 Mp3

Basically the operation of “mp3” is same as “all”.

7. MEDIA MANAGEMENT

49 DVB-S Receiver

7.1.3 Image

Basically the operation of “image” is same as

“all”, except that in the Yellow buttons offer

further functions to manage.

In image menu press [Yellow] button will

open another window.

press [OK] to set the image as background.

Select “Cancel” press [OK] to cancel the

operation.

7.1.4 Video

Basically the operation of “video” is same as “all”.

7.1.5 Music List

The color buttons offer further functions to manage.

Delete

In media list menu press [Red] button will

open another window where you can choose

between add one image and add all image.

• Del One

Press [Red] button to mark a image for

add. Marked image will be add after you

conﬁ rm to save the changes when you

leave this menu.

• Del All

a) Press [Green] button to show a add

icon behind all image name.

b) Press [MENU] button you will be asked “Are you sure to save?”. Select “OK” to add

all image. Select “Cancel” to cancel the operation.

Find

Basically the operation of “Music List Find” is same as “all Find”.

7. MEDIA MANAGEMENT

Installation Guide

7. MEDIA MANAGEMENT

7.1.6 Picture List

Basically the operation of “Picture List” is

same as “Music List”, except that in the

Yellow (Setup) buttons offer further functions

to manage.

Press [Yellow] button to open the “Serup”

window.

Select the item you want to adjust with

[CH ] and change the value with

[Vol ]

Size: Full and Real.

Time: 0 Sec, 1 Sec, 2 Sec, 3 Sec, 4 Sec, 5 Sec, 6 Sec, 7 Sec, 8 Sec and 9 Sec.

Repeat: On and Off.

Effect: Normal, Shutters, Brush, Slide, Random and Fade.

Mp3: On and Off.

7.1.7 Video list

Basically the operation of “Video List” is same as “Music List”.

7.1.8 Record list

If you enter the Record list menu a window

like the one below will open.

The color buttons offer further functions to

manage the channel list.

Rename

1. Press [Red] button to open the “Rename”

window like showed beside. Press

[CH

/[Vol ]to select the leading

character of the channel name and press

[OK] to conﬁ rm it.

2. After entering the character(s) highlight

“OK” in the window and press [OK] on the

RCU.

3. Press [Exit] button to close the ﬁ nd

window and brings you back to the Record

list.

51 DVB-S Receiver

7. MEDIA MANAGEMENT

Lock

In channel Record menu, press [Green] but-

ton to place a lock icon behind the name of

the highlighted Record. Marked Records will

be locked and displayed only after password

has been entered if you conﬁ rm to save the

changes when you leave this menu.

Copy

In channel Record menu, press [Yellow]

button copy the recorded programme to

another disk.

Press [Vol ] to switch select copy path,

Select “OK” to add all image. Select “Cancel”

to cancel the operation.

Delete

In channel Record menu, press [Red] button

will open another window where you can

choose between add one image and add all

image.

• Del One

Press [Red] button to mark a image for

add. Marked image will be add after you

conﬁ rm to save the changes when you

leave this menu.

• Del All

a) Press [Green] button to show a add icon behind all image name.

b) Press [MENU] button you will be asked “Are you sure to save?”. Select “OK” to

add all image. Select “Cancel” to cancel the operation.

Installation Guide

7.2 Media Control

1. Reserved TMS Size: Press [Vol ] to

switch between “0 MB / 200 MB and

500 MB”.

Select “MENU / EXIT”, press [MENU /

EXIT] to reset to make tms size valid now.

Select “Cancel” press [OK] to cancel the

operation.

2. Jump Step Value: Press [Vol ] to switch

between “1 mins / 3 Mins / 5 Mins / 10

Mins / 15 Mins”.

The value control the step of

operation.00

3. Record Type: Press [Vol ] to switch between “TS and PS”.

4. Test disk speed: Press [Vol ] to switch between “Off and On”.

5. Record Path: Press [Vol ] to switch select record path.

6. Fotmat Disk: If you want to delete the hard disk totally, you can do it with the [OK]

Button Format and the hard disk will be completely erased.

Caution: This process will delete also

saves you have made with Backup tools.

7.3 Disk Information

1. When you select the “Disk Information”

menu you will see a screen like beside. The

screen displays data about the current

HDD.

2. Press [Exit] button to leave the informa-

tion display.

7.4 Upgrade

Basically the operation of “Upgrade” is same

as “6.5.3”.

7. MEDIA MANAGEMENT

53 DVB-S Receiver

VIDEO

Decoding ...................................................................MPEG-2 & MEPG-1 compatible

Bit rate .......................................................................Max 15Mbps

Output.........................................................................PAL/NTSC

Aspect ratio .............................................................4:3, 16:9, Auto

Active pixel ................................................................720x480 @ 30fps; 720x576 @ 25fps

Output connector ..................................................RCA, TV SCART, HDMI

AUDIO

Decoding ...................................................................MPEG-2/MPEG-1 layer I & II

Mode ...........................................................................Mono, Dual, Stereo, Joint stereo

Bit rate .......................................................................Max 384Kbps

DEMODULATOR

Demodulation ..........................................................QPSK

Symbol rate .............................................................SCPC/MCPC

Outer code ...............................................................RS (204, 188, 8)

Inner code.................................................................ALL DVB rates

Energy dispersion ..................................................DVB-S recommendation

INPUT SIGNAL

Frequency .................................................................950MHz

2150MHz

Input level ..................................................................-65dBm

-25dBm

Channel bandwidth ...............................................36MHz

Input socked ............................................................F-type connector

LNB CONTROL

Power supply ...........................................................

13/18V (500mA max) with short circuit protection

Polarized control ...................................................13/18V polarization (vertical/horizontal)

DiSEqC control .......................................................DiSEqC1.0, DiSEqC1.1 and DiSEqC1.2

RF-MODULATOR

Input ............................................................................IEC 169-24 Male x 1

Output.........................................................................IEC 169-24 Female x 1

Band ............................................................................UHF

TV Standard ............................................................PAL BG/I/DK, NTSC M

Output Channel ......................................................21~69(PAL), 14~83(NTSC)

MISCELLANEOUS

Supply voltage .........................................................100~240VAC~50~60Hz

Power consumption .............................................Max. 25 watts

Operation temperature ......................................+5° to +40°

Storage temperature ..........................................-20° to +70°

Dimension (W x D x H) ........................................260x195x55 mm

Weight .......................................................................1.1 Kg

8. TECHNICAL SPECIFICATION

Installation Guide

DigitalBOX Europe GmbH

Sandstraße 65 · D-40878 Ratingen

Digitalbox IMPERIAL DB 2 USB Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Digitalbox IMPERIAL DB 2 USB

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info