499302

Digitalbox IMPERIAL DB 2 USB Handleiding

5
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
Installation Guide
IMPERIAL DB 2 USB
See the world through
3 DVB-S Receiver
GB
SAFETY PRECAUTION
Attachments: Never add any attachments and/or equipment without the manufac-
turer consent; as such additions may result in the risk of fi re, electric shock or other
personal injury.
Locating: Slots and openings in the cabinet are provided for ventilation to protect it
from overheating. Do not block these openings or allow them to be blocked by placing
the STB on a bed, sofa or other similar surface, nor should it be placed over a radiator
or heat register
Power-Cord Protection: Place the power-supply cord out of the way, where it will not
be walked on. Please take special attentions to cords at plugs, convenience recepta-
cles and the point where they exit from the unit.
Object and Liquid Entry: Never put objects of any kind into this STB through openings,
as they may touch dangerous voltage points or short-out parts that could result in a
fi re or electric shock. Never spill any liquid on the STB.
Note: Moisture may be formed inside the unit in the following conditions: When the
unit is suddenly moved from a cold environment or an air-condition room to a warm
place.
Immediately after a heater has been turned on. In a steamy or very humid room. If the
moisture forms inside the unit, it may not operate properly. To correct this problem,
turn on the power and wait about two hours for the moisture to evaporate.
Parts Replacement: When the unit parts need to be replaced, user should make sure
the service technician use the replacement parts specifi ed by the manufacturer or
having the same characteristics as the original part. Unauthorized replacement may
put the unit in the risk of fi re, electric shock or other hazards.
Safety Check: After all the maintenances and repairs are done, user is required to
request the service technician to conduct the overall safety check to ensure the ma-
chine is in the proper condition.
4
Installation Guide
GB
1. REMOTE CONTROL & PANEL DESCRIPTION .............................................. 7
1.1 Front Panel Description .......................................................................................................... 7
1.2 Rear Panel Description ........................................................................................................... 8
1.3 Remote Control Description ................................................................................................ 9
2. BASIC OPERATIONS ............................................................................................. 10
2.1 Switch on STB ............................................................................................................................ 10
2.2 Standby-Modus .......................................................................................................................... 10
2.3 TV/Radio .................................................................................................................................... 10
2.4 Code .............................................................................................................................................. 11
2.5 Mute ............................................................................................................................................... 11
2.6 Channel Numberr ..................................................................................................................... 11
2.7 INFO ................................................................................................................................................ 11
2.8 MULTI-PIC ..................................................................................................................................... 11
2.9 FAV .................................................................................................................................................. 12
2.10 PGUP / PGDN ........................................................................................................................... 12
2.11 BACK .............................................................................................................................................. 12
2.12 EPG ................................................................................................................................................. 13
2.13 FAV +/- .......................................................................................................................................... 14
2.14 Menü .............................................................................................................................................. 14
2.15 Exit ................................................................................................................................................... 14
2.16 CH ........................................................................................................................................ 14
2.17 Vol ............................................................................................................................................. 14
2.18 OK .................................................................................................................................................... 14
2.19 PIP (Picture in Picture) ........................................................................................................... 15
2.20 PVR-LISTE ..................................................................................................................................... 15
2.21 Audio .............................................................................................................................................. 16
2.22 Zoom ...............................................................................................................................................16
2.23 SUBT ...............................................................................................................................................16
2.24 TXT ...................................................................................................................................................16
2.25 PAUSE .............................................................................................................................................17
2.26 A-B ....................................................................................................................................................17
2.27 T.S. ....................................................................................................................................................17
2.28 Goto .................................................................................................................................................17
2.29 ........................................................................................................................................................17
2.30 ........................................................................................................................................................18
2.31 ................................................................................................................................................18
2.32 .......................................................................................................................................................18
2.33 ......................................................................................................................................................18
2.34 ..............................................................................................................................................18
2.35 LNB Short .....................................................................................................................................18
CONTENTS
5 DVB-S Receiver
GB
3. CHANNEL .................................................................................................................. 19
3.1 TV Channel List ...........................................................................................................................19
3.1.1 Favorite .............................................................................................................................. 20
3.1.2 Move .................................................................................................................................. 20
3.1.3 Sort .....................................................................................................................................21
3.1.4 Edit .......................................................................................................................................21
3.1.5 Find ..................................................................................................................................... 23
3.2 Radio Channel List .................................................................................................................... 23
3.3 Channel Setup ............................................................................................................................ 23
3.4 Favorite group list name ........................................................................................................24
3.5 Delete All .......................................................................................................................................24
3.6 Restore channel list and settings ......................................................................................24
3.7 Save channel list and settings ............................................................................................ 25
4. INSTALLATION ....................................................................................................... 26
4.1 Single Search ............................................................................................................................. 26
4.2 Multi Search ............................................................................................................................... 28
4.3 TP Scan ......................................................................................................................................... 28
4.4 Satellite List ................................................................................................................................. 30
4.5 TP List .............................................................................................................................................31
4.6 Satellite Guide ............................................................................................................................ 32
5. SYSTEM SETUP .......................................................................................................33
5.1 Language ...................................................................................................................................... 33
5.2 TV System.....................................................................................................................................34
5.3 Time & Timer Setting ...............................................................................................................34
5.4 OSD Setting ................................................................................................................................. 36
5.5 Parental Lock ..............................................................................................................................37
5.6 Power setting ............................................................................................................................. 38
6. TOOLS ..........................................................................................................................39
6.1 Information .................................................................................................................................. 39
6.2 Quick Setup ................................................................................................................................. 39
6.3 Game .............................................................................................................................................. 40
6.4 Factory Default .......................................................................................................................... 42
6.5 Software Upgrade .................................................................................................................. 42
6.5.1 Software Upgrade ..................................................................................................... 42
6.5.2 Upgrade by Satellite................................................................................................... 43
6.5.3 Upgrade .......................................................................................................................... 43
6.6 SatcoDX Auto Programming ..............................................................................................44
CONTENTS
6
Installation Guide
GB
7. MEDIA MANAGEMENT ..........................................................................................45
7.1 Media-List ..................................................................................................................................... 45
7.1.1 All ............................................................................................................................................ 46
7.1.2 MP3 ..................................................................................................................................... 48
7.1.3 Image ................................................................................................................................... 49
7.1.4 Video .................................................................................................................................... 49
7.1.5 Music List .......................................................................................................................... 49
7.1.6 Picture List ........................................................................................................................ 50
7.1.7 Video list ............................................................................................................................. 50
7.1.8 Record list ......................................................................................................................... 50
7.2 Media Control ............................................................................................................................. 52
7.3 Disk Information ........................................................................................................................ 52
7.4 Upgrade ........................................................................................................................................ 52
8. TECHNICAL SPECIFICATION ................................................................................53
CONTENTS
7 DVB-S Receiver
GB
1. REMOTE CONTROL & PANEL DESCRIPTION
1.1 Front Panel Description
No Key Description
1 Display Displays the received channel number while operating
(4-Digit/7-Segment) and time while in standby mode.
2 POWER Is used to switch between the working mode and the
standby mode.
3 VOL+/- To change volume to move cursor,
change numbers in
the menu or to change the choice
4 MENU To enter into the main menu and
exit all menus.
5 OK To select an item in the menu and confi rm
it or pop up channel list when no menu.
6 CH+/- To change channels or for navigating and changing
values in menus.
7 Remote Sensor Detects the infrared signals from the remote control
unit.
2 3 546
1 7
8
Installation Guide
GB
52
31
4
8
1. REMOTE CONTROL & PANEL DESCRIPTION
1.2 Rear Panel Description
No Key Description
1 TV SCART Output SCART for the connection to a TV set.
2 IF IN Satellite input.
3 IF OUT Satellite output for cascading to other devices
Note: The operation of another receiver at the same
time is only possible with limited channel selection.
4 AUDIO HiFi outputs for stereo set
5 VIDEO CVBS video output for TV AV in.
6 S/PDIF Digital output for Dolby Digital.
7 USB USB-Port for record and replay from extrem media
8 AC IN Mains input cable.
9 POWER ON/OFF Allows to completely switch off the receiver.
6
7
9
9 DVB-S Receiver
GB
1. REMOTE CONTROL & PANEL DESCRIPTION
1.3 Remote Control Description
10
Installation Guide
GB
2.1 Switch on STB
Switch the [Device’s Main Power] switch on.
When the STB is fi rst used it will display “Quick Setup” window. you will set Language,
First Audio, Second Audio, LNB Power, Antenna Setup and Multi Search.
? Frequently Asked Question
Q: The power of my STB is on and it is running in TV mode but the TV screen shows
nothing:
A: Make sure the TV set has been set to the correct video input(not the TV
channels). For example, if you have connected the unit to the video1 input of the
TV set then you need to select the corresponding input of the TV. Mostly it is
done with the AV button of the TVs remote control unit.
Q: My STB is running in TV mode but the TV screen shows nothing except one ball
and “No Signal”.
A: That means the channel you selected has no signal. This can be caused by several
reasons:
1. The channel you selected is not from the satellite to which your dish is pointing. Select
another channel.
2. The signal of current TV channel is too weak. You can try to change to other channels
with a stronger signal. If the problems still exist, please consult your local dealer or
installer for technical service.
3. You selected the wrong LNB type in the installation menu or your DiSEqC switch
confi guration is not correct.
2.2 Standby Mode
1. Press [Power] button to switch from TV/radio mode to standby mode
2. In standby mode press [Power] button again to switch back to TV/radio mode. The
last active channel will be showed.
3. To switch off the STB complete press the main power button.
2.3 TV/Radio
In TV mode, press [TV/Radio] to switch to Radio mode. In Radio mode press
[TV/Radio] again to switch back to TV mode.
2. BASIC OPERATIONS
11 DVB-S Receiver
GB
2. BASIC OPERATIONS
2.4 Code
For this, press the button CODE on your re-
mote control until the correct LED is lighting.
2.5 Mute
1. Press the [Mute] button to mute the sound. On the screen an icon will be displayed
to indicate the muted sound.
2. Press the [Mute] button again to restore the sound.
2.6 Channel Number
In TV mode you can enter the channel number directly with your remote control unit and
confi rm the number with the OK button to change to the desired channel.
2.7 INFO
In TV mode, press [INFO] button can open
information screen, in the window shows the
parameters of current channel.
Two dynamic bars at the bottom of the
window refl ect the signal intensity and signal
quality of the current channel.
12
Installation Guide
GB
2.8 MULTI-PIC
In TV mode, press [0] key to enter the
“MULTI-PIC” menu.
1. In “MULTI-PIC” menu, you can choose
channels’ preview window(static), starting
from the current channel. Only the
marked preview program is continuously
playing.
2. Press [CH
] / [Vol ] to change
the marked channel among the preview
programs.
3. With the number buttons [1] ~ [9] you can directly move the highlight to the related
channel.
4. With [OK] you return to full screen mode in the marked channel.
2.9 FAV
1. In TV mode press the [FAV] button to
display the Favorite Group window on the
screen as the picture beside shows.
2. In the Favorite Group window you can
select the desired favorite channel with
[CH ] and confi rm it with [OK] to
switch to it. In bigger groups you can
navigate with [PGUP/ PGDN].
3. With [Vol ]. You can select different
Favorite Groups.
4. Press [Exit] to close the Favorite Group window.
? Frequently Asked Question
Q: Why the screen displays “No Favorite Channel” after pressing the [Favorite] but-
ton?
A: No channels have been assigned to a Favorite Group yet. You can do this in the chan-
nel menu..
2.10 PGUP / PGDN
Drücken Sie im TV-Modus [PGUP/PGDN], um direkt zwischen Satelliten umzuschalten.
2. BASIC OPERATIONS
35 DVB-S Receiver
GB
• When you select “TV Channel / Radio Channel”(timer setting for channel
change and Wakeup channel / date) then you have further options you need
to set:
Wakeup Channel: Press [OK] to enter the channel list, and select the channel
you want to see with [CH
] press [OK] to confi rm it.
Wakeup Date: Use number buttons to input your wakeup date.
On Time: Use number buttons to input your wakeup time. If date and time are
reached then no matter if the system is in standby mode or in playing mode, it
will automatically switch to the channel you set and start to play.
Duration: Here you can set the time you want to see or play this channel. When
the time is reached, whenever the system is in standby mode or playing a
channel, the system will automatically switch to the channel you select and
play the channel within the duration time you set. The minmum duration unit is
one minute. After the duration time, the system will automatically switch to
Standby mode.
• When you select “Message”(reminding message) option in “Timer Service” then
you can enter additional data:
Wakeup Message: Press [Vol ] to select the category
of the wakeup message from Birthday, Anniversary and General.
Wakeup Date: Use the [Number] buttons to input your wakeup date.
On Time: Use the [Number] buttons to input your wakeup time. If date and time
are reached, no matter if the system is in standby mode or in playing mode, it
wil automatically show a reminding message. The message will be displayed on
the screen until you press [Exit] to close it.
Duration: Here you can set the time you want to see or play this channel. When
the time is reached, whenever the system is in standby mode or playing a
channel, the system will automatically switch to the channel you select and play
the channel within the duration time you set. The minmum duration unit is one
minute. After the duration time, the system will automatically switch to Standby
mode.
• Press [Exit] to leave the “Timer” menu
2. Local Time Setting: When you select
“Local Time Setting” and press [OK] then
you will see a window like the one beside:
• GMT Usage: This item is used to set
the time by using the time signal from
the satellite. Press [Vol ], to
change the setting.
• The “GMT Offset” item is only available
when “GMT Usage” is set to “On”. Press
[Vol
], to set the “GMT Offset”
value. With every time you press the
button the time offset will be
increased/decreased by half an hour.
5. SYSTEM SETUP
36
Installation Guide
GB
• Summer: Press [Vol ] to switch this function “On” or “Off”.
• “Date” and “Time” items are only available when the “GMT Usage” is set to “Off”.
Press [Vol
] to select one item and use number buttons to input time and date
directly.
• Time Display: Press [Vol
] to switch this function “On” or “Off”.
NOTE:
If the current channel provides the correct time information, you will see the
current time after you entered “Local Time Setting” menu. If the channel doesn’t
provide time information, you have to input the date and time information manually.
The most channels support the time signal.
• Press [Exit] to leave the “Time” menu.
3. Sleep Timer: Select “Sleep Timer” item and press [OK] to set the sleep timer. You will
see “Sleep timer OFF / Sleep timer 10 / Sleep timer 30 / Sleep timer 60 / Sleep
timer 90 / Sleep timer 120”.
If you set a sleep time, the system will change to standby mode after the chosen time
period.
5.4 OSD Setting
When you select “OSD Setting” you will see a
screen like beside:
1. Subtitle Display: Press [Vol ] to
select “Off”, “Standard” or “Teletext
Subtitle”. If the current channel has
subtitle information, it will be displayed
if this function is “Standard” or “Teletext
Subtitle”. If this function is “Off” subtitles
won’t be displayed.
2. OSD Timeout: This setting determines the duration the info window is displayed on
the screen when you change channels. Press [Vol ] to set the time between 1 to
10 seconds.
3. Position: Press [Vol ] select the position between top and bottom.
4. OSD Transparency: With this parameter you can set the transparency of the menus.
Press [Vol ] select the value between 10%, 20%, 30%, 40% and “Off”(means no
transparency function).
5. Load OSD Setting Default: If you want to reset your OSD settings to the default set-
tings then select this item and press [OK].
6. Press [Exit] button to leave the “OSD Setting” menu.
5. SYSTEM SETUP
37 DVB-S Receiver
GB
5.5 Parental Lock
You can set a password for anyone who
wishes to operate the “Installation” menu.
You can also set the password to lock chan-
nels. Below you fi nd how to set and change
the password.
1. On “Parental Lock” press [OK] to open
a dialogue box and input the password.
After you entered the correct password,
you will see a screen like beside:
2. Menu Lock: If Menu Lock is set to “Yes” then you need to enter the password every
time you want to open the menu. If set to “No” then you can open the menu without
entering the password fi rst.
3. Channel Lock: If set to “Yes” then you need to enter the password before you can see
those channels which have been marked as locked channels in the channel menu. If
set to “No” then even those channels can be selected without entering the password
fi r s t .
4. New Password: Here you can change the existing password. You should do this
after you set up the receiver the fi rst time and every time when you think that your
password is known by unauthorized persons. To change the password enter the new
password in the “New Password” item and repeat the same one in the “Confi rm Pass-
word” item. If the passwords are not identically then you will see a warning message.
If you entered the same new password in both fi elds then you will see the message
“Saving Data, Please Wait…”. From now on you need to use the new password to
open locked menus or locked channels.
NOTE: The default password is 0000.
5. Press [Exit] to leave the “Parental Lock” menu.
5. SYSTEM SETUP
38
Installation Guide
GB
5.6 Power setting
When you select this option, you will see a
screen like beside:
LNB Power: If your receiver is connected
to the LNB directly then you need to set
the LNB Power to “On”. If your receiver is
connected to a multi switch (SMATV signal
distribution system) then it may be that you
don’t need to provide the power to the LNB.
But since this is depending on the kind of
installed distribution system we recommend
you to contact your installer or to refer to
the user manual of this system to get the
correct information.
You also just can change this setting and
check if you still can receive the channels. If
the LNB Power is off and you still can see all
channels then we recommend this setting.
5. SYSTEM SETUP
39 DVB-S Receiver
GB
When you enter to “Tools” menu, you will see
a screen like beside:
In “Tools” menu:
1. Press [CH ] to select the wanted
item among Information, Quick Setup,
Game, Factory Default, Software Upgrade,
SatcoDX Auto Programming Smart and
Smart Card.
2. Press [OK] to enter the selected item.
6.1 Information
1. When you select the “Information” menu
you will see a screen like beside. The
screen displays data about the current
channel.
2. Press [Exit] button to leave the
information display.
6.2 Quick Setup
When the STB is used, which need to repeat
set menu Language, First Audio, Second
Audio, LNB Power, Single Search and Multi
Search.
6. TOOLS
40
Installation Guide
GB
6.3 Game
When you enter “Game” menu, you will
see three games include Tetris, Snake and
Othello.
Basic operation statement:
1. Tetris
Mark “Setup” and press [Vol ] to
select the level (speed).
Mark “Start” and press [OK] to start
the game.
Mark “Cancel” and press [OK] to leave
the game.
Play the game:
• Press [Vol ] to move the block left
or right
• Press [Channel Up] to rotate the
block clockwise
• Press [Channel Down] to drop the
block faster
• Press [OK] to Pause/Play the game
• Press [Exit] to leave the game and
return to the game menu.
6. TOOLS
41 DVB-S Receiver
GB
2. Snake
Mark “Setup” and press [Vol ]
to select the level (speed).
Mark “Start” and press [OK] to start
the game.
Mark “Cancel” and press [OK] to leave
the game.
Play the game:
• Press [Vol ]/[CH ] to guide
the snake to the red blocks. Every
block you ate increases the length of
the snake. If the snake runs against a
wall or against itself then it dies.
• Press [OK] to Pause/Play the game
• Press [Exit] to quit the game and
return to the game menu.
3. Othello
Mark “Setup” and press [Vol ] to
select the game level(degree of
diffi culty).
Mark “Start” and press [OK] to start
the game.
Mark “Cancel” and press [OK] to leave
the game.
Play the game:
• Press [Vol ]/[CH ] to
position the round mark.
• Press [OK] to set your stone.
• Press [Exit] to quit the game and
return to the game menu.
6. TOOLS
42
Installation Guide
GB
6.4 Factory Default
When you press [OK] on the “Factory
Default” item:
1. A dialogue box will occur where you need
to enter the password.
2. After you input the correct password a
warning message will be displayed like the
one beside.
3. If you select “Yes” then all changes you
made will be reset to default values. Make
sure you really want to do this!
4. Press [Exit] in both steps will close the
window without resetting the receiver.
6.5 Software Upgrade
When you enter to “Software Upgrade”
menu, you will see a screen like beside:
1. Press [CH ] to select the wanted
item among Software Upgrade and Up-
grade by Satellite.
2. Press [OK] to enter the selected item.
6.5.1 Software Upgrade
1. This function allows you to upgrade the
software of the receiver. This can be done
from PC to receiver or from a master
receiver to a slave receiver.
6. TOOLS
43 DVB-S Receiver
GB
2. Connect master receiver or PC to the slave receiver via serial interface (0-Modem
cable). Enter the “Software Upgrade” menu of the master receiver and press
[Vol
] to change the upgrade mode. Upgrade modes include: All code / Main code
/ CAS-data / Script GUI / Radio Back / default DB / Userdb.
3. Switch on the slave receiver.
4. Mark “Start” on the master reeciver and press [OK] to start upgrade.
Wait until the display on the front panel shows “-END”. Then switch off the receiver
and on again. Now the new software is used.
5. Press [MENU] to save the setting without upgrade.
6.5.2 Upgrade by Satellite
This function can upgrade the software of
your receiver through data sent by a satellite.
At the moment we offer satellite updates
only through ASTRA1 and Hotbird satellites.
1. Select the satellite and TP or input the TP
value and download PID.
2. Then mark “Start” and press [Enter] to
begin the download of the upgrade. This
may need up to 60 minutes. Therefore we
suggest using of this function only if you
don’t intent to watch TV during this time
6.5.3 Upgrade
This option allows updating the software of
the receiver with the received data from a
USB memory device. To do it, connect a USB
memory device to the receiver and accede to
this menu option.
The last software version to be loaded must
be placed at the root path of your USB
device.
1. Update fi le: Select with [Vol
], the name
of the fi le to be choosed.
2. Select “Start” and press [OK]. An alert
message appears indicating not to take
out the memory device during the loading
process.
6. TOOLS
… 5 …

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Digitalbox IMPERIAL DB 2 USB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Digitalbox IMPERIAL DB 2 USB in de taal/talen: Engels als bijlage per email.

De handleiding is 3,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Digitalbox IMPERIAL DB 2 USB

Digitalbox IMPERIAL DB 2 USB Gebruiksaanwijzing - Deutsch - 58 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info