498836
1
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
INSTRUCTION MANUAL
CAR STEREO CD/CDR/CDRW/MP3/WMA PLAYER
WITH PLL FM STEREO RADIO
RDS
USB / SD / MMC CARD INPUT
FLIP DOWN/DETACHABLE FRONT PANEL
CAD-490
PTY
AFTA
63
54
RELEASE
21
DISP
A/PS
PWR
BAND
TUNE/TRACK
SCN PAU INT RPT RDM
EJ
MD
V
O
L
P
U
S
H
S
E
L
E
C
T
E1
LOCATION OF PARTS AND CONTROLS
1. POWER ON/OFF ( )
2. FUNCTION SELECT BUTTON: BASS/TREBLE/BALANCE/FADER / TA SEEK/MASK
DPI/RETUNE/AUDIO DSP/LOUDNESS/ESP/CD MULTI/BEEP/SEEK/STEREO/LOCAL
3. VOL UP/VOL DOWN FOR BASS/TREBLE/BALANCE/FADER / TA SEEK/MASK DPI/
RETUNE/AUDIO DSP/LOUDNESS/ESP/CD MULTI/BEEP/SEEK/STEREO/LOCAL
4. PRESET STATIONS (1,2,3,4,5,6)
5. ‘AF’ function (ALTERNATIVE FREQUENCIES)
6. ‘TA function (TRAFFIC ANNOUNCEMENT)
7. ‘PTY’ function (PROGRAM TYPE)
8. DISPLAY BUTTON (DISP)
9. MODE BUTTON (MD)
10. BAND BUTTON (BAND)
11. AUTOMATIC OR MANUAL TUNING (FREQ UP
OR
FREQ DOWN
)/ CD TRACK/SEARCH BUTTON
12. AUTO SEEK SEARCH TUNING (A/PS)
13. ‘SCAN’ AUTOMATIC TUNING CONTROL (SCN)
14. LCD DISPLAY
15. OPEN PANEL BUTTON (
)
16. CD SLOT
17. CD EJECT BUTTON (
)
18. PAUSE BUTTON
19. INTRO BUTTON (Preview all Tracks)
20. REPEAT BUTTON
21. RANDOM BUTTON
22, 23. + 10 TRACK SEARCH DOWN/UP
24. USB PORT
25. MULTI-MEDIA CARD (MMC) / SD CARD SLOT
26. RESET BUTTON
27. POWER INDICATOR LED
PTY
AFTA
63
54
RELEASE
21
DISP
A/PS
PWR
BAND
TUNE/TRACK
SCN PAU INT RPT RDM
EJ
MD
V
O
L
P
U
S
H
S
E
L
E
C
T
4
(1-6)
15179
25161 2 3 1411
245 762322212019181310812
26 27
RESET
E2
53mm
182mm
3
2
182mm
53mm
1
2
1
3
4
INSTALLATION
PRECAUTIONS
Choose the mounting location carefully so that the unit will not interfere with the normal
driving functions of the driver.
Avoid installing the unit where it would be subject to high temperatures, such as from direct
sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive
vibration.
Use only the supplied mounting hardware for a safe and secure installation.
Be sure to remove the front panel before installing the unit.
NOTE : Inclination angle for car radio installation must not
exceed 30˚ otherwise the front panel will not open.
Note: Keep the release key in the safe place as you may need it in future to remove the unit
from the car.
Bend these
claws, if necessay
release screw and
bracket
ISO CONNECTOR
RCA Jack Line Out: RCA Jack Line In:
: Red (right) : Red (right)
: White (left) : White (left)
CONNECTOR A
1.
2.
3.
4. MEMORY +12V
5. AUTO ANTENNA OUTPUT
6.
7. +12V (TO IGNITION KEY)
8. GROUND
Note: (connector A no. 7) must be connected by car ignition key in order to avoid that car
battery becomes weak when the car will be not used for long period.
CONNECTOR B
1. REAR RIGHT SPEAKER (+)
2. REAR RIGHT SPEAKER (-)
3. FRONT RIGHT SPEAKER (+)
4. FRONT RIGHT SPEAKER (-)
5. FRONT LEFT SPEAKER (+)
6. FRONT LEFT SPEAKER (-)
7. REAR LEFT SPEAKER (+)
8. REAR LEFT SPEAKER (-)
Maintenance
FUSE REPLACEMENT
If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after the
replacement, there may be an internal malfunction. In this case, consult your nearest repairing center.
Warning
Use the specified amperage fuse for each lead. Use of a higher amperage fuse may cause serious dam-
age.
B
1 3 5 7
2 4 6 8
5 7
4 8
A
E3
10
7
1
2
3
4
4
4
5
5
6
6
8
9
TO SUPPORT THE UNIT
Detaching and attaching the front panel
The front panel of this unit can be detached in order to prevent
the unit from being stolen.
DETACHING THE FRONT PANEL
Before detaching the front panel, be sure to press the
OFF
button first. Then press the button (15)
and detach the panel
by pulling it towards you as illustrated.
Note:
Be sure not to drop the panel when detaching it from the unit.
Notes:
Make sure that the front panel is the right way up when
attaching it to the unit as it cannot be attached upside
down.
Do not press the front panel hard against the unit when
attaching it. It can be easily attached by pressing it lightly
against the unit.
When you carry the front panel with you, put it in the
supplied front panel case.
Do not press hard or give excessive pressure to the display
window of the front panel when attaching it to the unit.
1. UNIT
2. RELEASE CASE
3. DASH BOARD
4. HEX NUT
5. LOCK WASHER
6. PLAIN WASHER
7. CAR BODY
8. REAR SUPPORT STRAP
9. TAPPING SCREW
10. M5 X 15 HEX BOLT
Dashboard
B
A
Front panel
Main unit
Rear of the front panel
Front panel
Panel case
Front panel
E4
1. POWER ON/OFF (
)
By pressing this key, the unit is on and off.
This unit is turned on by pressing any key.
2,3.
FUNCTION SELECT BUTTON: BASS/TREBLE/BALANCE/FADER / TA SEEK/MASK DPI/RETUNE/
AUDIO DSP/LOUDNESS/ESP/CD MULTI/BEEP/SEEK/STEREO/LOCAL
Turning the VOL knob Right or Left (3), you can adjust VOL/BASS/TREB/BAL/FAD. To select other
functions, press the VOL knob shortly until the desired functions is shown on the display. Figure 1
shows how control functions are selected using the VOL knob.
Fig. 1 Selection of sound control functions
1. VOL 2. SEL 3. BAS 4. TRE 5. BAL 6. FAD
Turning the VOL knob Right or Left. Increase or decrease the volume by turning
VOL
or
VOL
. These
buttons can be used to adjust the BASS, TREBLE, BALANCE and FADER.
TA SEEK/TA ALARM (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these func
-
tion.
TA SEEK Mode or TA ALARM mode is selected by
VOL
or
VOL
.
- TA SEEK mode:
When newly turned station does not receive TP information for 5 sec., the radio retunes to next station
which has not the same station (PI) as the last station, but has the TP information.
In TA seek mode, the current station can be changed to the completely different station because the
unit searches TP station when the field strength of the current station is very weak, or the current
station has no TP signal.
- TA ALARM mode:
Any automatic retune mode is not activated, just can hear Beep sound.
MASK DPI (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these func
-
tion.
MASK DPI: masked only the AF which has different PI.
MASK ALL: masked the AF which has different PI and NO RDS signal with field strength.
RETUNE L / S CONTROLS (2)
When press the SEL button for more than 2 seconds, it is activated as selecting Retune mode.
RETUNE L: Select 90 seconds as the initial time of automatic TA search.
RETUNE S: Select 30 seconds as initial time.
AUDIO DSP CONTROLS (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these func
-
tion.
1 3
2
4
2
5
2
6
2
2
TA SEEK
SEL
2 sec.
TA SEEK / TA ALARM
VOL
TA SEEK
SEL
MASK DPI
SEL
2 sec.
MASK DPI / MASK ALL
VOL
TA SEEK
SEL
RETUNE
SEL
MASK DPI
SEL
2 sec.
RETUNE L / RETUNE S
VOL
TA SEEK
SEL
2 sec.
SEL
DSP ONMASK DPI
SEL
RETUNE
SEL
POP M --- ROCK M --- CLASS M --- FLAT M --- DSP OFF
VOL
E5
2 sec.
TA SEEK
SEL
2 sec.
SEL
LOUD
SEL
MASK DPI
SEL
SEL
RETUNE DSP
SEL
ESP
CD MULTI ON/OFF
SEL
MULTI
VOL
ESP
ESP12 / ESP 45
TA SEEK
SEL
2 sec.
SEL
SEL
MASK DPI
SEL
RETUNE DSP
SEL
LOUD
SEL
VOL
TA SEEK
SEL
2 sec.
SEL
SEL
MASK DPI
SEL
RETUNE DSP
SEL
LOUD ON/OFF
VOL
SEL
TA SEEK
SEL
2 sec.
SEL
LOUD
SEL
MASK DPI
SEL
SEL
RETUNE DSP
SEL
ESP
SEL
MULTI
LOCAL/DX
LOCAL
SEL
STEREO
SEL
SEL
SEEK
BEEP
VOL
TA SEEK
SEL
2 sec.
SEL
LOUD
SEL
MASK DPI
SEL
SEL
RETUNE DSP
SEL
ESP
SEL
MULTI
2 sec.
ON/OFF
SEL
BEEP
VOL
SEL
TA SEEK
SEL
2 sec.
SEL
LOUD
SEL
MASK DPI
SEL
SEL
RETUNE DSP
SEL
ESP
SEL
MULTI
SEL
SEEK1 / SEEK 2SEEK
BEEP
VOL
SEL
TA SEEK
SEL
2 sec.
SEL
LOUD
SEL
MASK DPI
SEL
SEL
RETUNE DSP
SEL
ESP
SEL
MULTI
STEREO/MONO
STEREO
SEL
SEL
SEEK
BEEP
VOL
LOUDNESS CONTROLS (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function.
LOUD ON/OFF mode is selected by
VOL
or
VOL
. The bass and treble response will be boosted.
ESP MODE (2)
When press the SEL button for more than 2 seconds, it is activated as 12 sec. or 45 sec. of ESP mode
can be selected.
MULTI CD SECTION MODE (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function.
CD MULTI ON/OFF mode is selected by
VOL
or
VOL
. CD MULTI ON: Read multi section CD. CD
MULTI OFF: Read first section only.
BEEP MODE (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function.
BEEP ON: BEEP sound can be heard from speaker when the buttons are pressed.
SEEK MODE (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function.
SEEK 1: When SEEK 1 mode is activated, AUTO SEEK SCAN is stopped when station is detected
even user still push SEEK button.
SEEK 2:
Auto SEEK SCAN is not stopped even station is detected if user push SEEK button. When
release this SEEK button, then stop when station is detected.
STEREO/MONO (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function.
When FM stations are weak and are disturbed, listening can be improved by selecting MONO.
LOCAL/DX (2)
When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function.
E6
“Local” position in areas with strong signals to let radio stop at only strong stations during manual
tuning (LOC appears). Press to Distant position in areas with weak signals to listen to all stations.
4. PRESET STATIONS (1,2,3,4,5,6)
(A) RADIO MODE:
When pressed short, these keys select a preset station directly. When pressed longer than 1 sec.,
current station is stored in preset memory bank. When PTY mode is selected, the PTY switch is shared
as follows:
PTY music group ---- PTY speech group ---- OFF
MUSIC SPEECH
1. POP M, ROCK M 1. NEWS, AFFAIRS, INFO
2. EASY M, LIGHT M 2. SPORT, EDUCATE, DRAMA
3. CLASSICS, OTHER M 3. CULTURE, SCIENCE, VARIED
4. JAZZ, COUNTRY 4. WEATHER, FINANCE, CHILDREN
5. NATION M, OLDIES 5. SOCIAL, RELIGION, PHONE IN
6. FOLK M 6. TRAVEL, LEISURE, DOCUMENT
(B) CD/MP3/WMA PLAYER MODE:
1. PAUSE 2. INT 3. RPT 4. RDM
USING THE RDS FUNCTION
What is RDS?
The RDS (Radio Data System) is a digital information system developed by the EBU (European Broad-
cast Union). Piggy-backed on normal FM broadcasts, RDS offers a variety of information services and
automatic retuning functions for RDS-compatible car stereos.
In 1988, RDS became available in the United Kingdom, France, West Germany, Ireland and Sweden.
Test transmissions are being conducted in many other european countries. It is expected that RDS will
be available in most western european countries in the near future.
5. ‘AF/REG’ function (ALTERNATIVE FREQUENCIES)
When pressed short, AF/REG switching mode is selected.
When AF/REG switching mode is selected, the radio checks the signal strength of the AF all the time.
When pressed long, it is activated as regional mode ON/OFF.
– Regional mode ON:
AF switching or PI SEEK is implemented to the station which have all PI codes same as current sta
-
tion. REG segment is turned on, in LCD display.
– Regional mode OFF
The regional code in the format of PI code is ignored when AF switching or PI SEEK is implement-
ed.
6. ‘TA’ function (TRAFFIC ANNOUNCEMENT)
When pressed short, it is activated as TA mode on or off
When TA mode is on and traffic announcement is transmitted
– When the unit is CD/MP3 mode, it will switch to radiomode temporarily.
– If the volume level was under the threshold point, it will be raised to the threshold point.
– When TP station is received, TP segment is turned on in LCD display.
7. ‘PTY’ function (PROGRAM TYPE)
PTY MUSIC ---- PTY SPEECH ---- PTY OFF
While selecting PTY type, its selection is implemented by preset buttons as described in preset key.
When PTY is selected, the radio starts to search corresponding PTY information, and stops if the
corresponding PTY information is detected.
8. DISPLAY (DISP)
Press DISP button to switch between display informations such as radio frequencies, clock, track and
other informations depending on the playing MODE.
9. MODE BUTTON (MD)
By pressing this key, user can select. AUX/TUNER/CD-MP3/USB or MMC/SD mode.
10. BAND BUTTON (BAND)
Each band is toggled cyclically by pressing this key FM1---FM2---FM3.
E7
11. AUTOMATIC OR MANUAL TUNING (FREQ UP
OR FREQ DOWN )
(A) RADIO MODE
When pressed short, these keys are operated as MANUAL tuning mode.
When pressed longer than 1 sec., they are operated as SEEK tuning mode.
(B) CD/MP3/WMA PLAYER MODE
When pressed short, they are operated as TRACK UP or TRACK DOWN mode.
When pressed longer than 1 sec., they are operated as CUE or REVIEW mode.
12. AUTO SEEK SEARCH TUNING (A/PS)
By pressing shortly, the radio searches for each preset station.
When field strength level is bigger than the threshold level of stop level, the radio is holding at that
preset number for 5 sec. with releasing mute, and then searches again.
By pressing longer than 1 sec, and then 6 strongest stations are preset to the corresponding preset
number. When AS operation is finished, the radio executes the preset scan.
13. ‘SCAN’ AUTOMATIC TUNING CONTROL (SCN)
This key is operated as RADIO SCAN. The operation is similar as normal search but different thing
is holding 5 seconds on every station detected in RADIO SCAN mode.
14. LCD DISPLAY
The Liquid Crystal Display will display the current state of the unit.
15. OPEN THE FRONT PANEL
Press
button and the front panel will open.
CD CONTROL LOCATION OF PARTS
TRACK/SEARCH BUTTON (11)
FORWARD AND REVERSE TRACK SEARCH (or changing songs)
Press the SKIP button (
or ) during play to go to the desired track(song).
....REVERSE ....FORWARD
Press and hold the SKIP button (
or ) during play to scan the disc at high speed. When the desired
music section of the disc is found, release the button. Normal play will resume.
16. CD SLOT
17. CD EJECT BUTTON
Press the
button to remove the CD.
18. PAUSE BUTTON
During “PLAY”, press (18) ‘PAU’ button to “PAUSE”. Press it again to resume play.
19. INTRO BUTTON (Preview all Tracks)
When this button is pressed, ‘INT ON’ indication is displayed and the first several seconds of each
track of the disc are played. Press again to stop intro and listen to track.
20. REPEAT BUTTON
When this button is pressed, ‘RPT ON’ indication is displayed and play of the selected track will be
continually repeated until the Track repeat mode is cancelled by pressing ‘RPT’ button again.
21. RANDOM BUTTON
When this button is pressed, ‘RDM ON’ indication is displayed and each track of the disc are played in
random instead of normal progression. To cancel RANDOM mode, press ‘RDM’ button (21) again.
22, 23. 10 TRACK DOWN/UP SELECT: (In case of MP3/WMA files)
M5: 10 Track down / M6: 10 Track up
E8
HOW TO SELECT MP3/WMA FILES
1. Searching Track:
Press “A/PS”, then searching track is activated.
Press “VOL”, then the first digit is blinking.
With “VOL
VOL
/ VOL
VOL
” knob, select first digit you want.
Press “VOL”, then the first digit is fixed and second digit is blinking.
With “VOL
VOL
/ VOL
VOL
” knob, select 2’nd 3’rd respectively.
Then automatically the song you selected will start.
2. Searching File Name:
Press “A/PS” twice, then file search is activated.
Press “VOL”, then the first directory is displayed.
With “VOL
VOL
/ VOL
VOL
” knob, you can select the directory you want.
Press “VOL” again, then the directory is fixed and the first file name is displayed.
With “VOL
VOL
/ VOL
VOL
” knob, you can select the file you want.
Press “VOL”, then the song you selected will start.
3. Searching Character:
Press “A/PS” 3 times, then character search mode is activated.
Press enter “VOL” button, then “A” character is displayed.
With “VOL
VOL
/ VOL
VOL
” knob, you can select the letter you want.
Press enter “VOL” key longer than 2 sec.
The song which has same character you selected is displayed.
With “VOL
VOL
/ VOL
VOL
” knob, you can select the song you want.
Press enter “VOL” key, then the song you selected will start.
Connecting it to Portable MP3 Player
24. USB Port
Using USB cable to connect Your Portable MP3 Player.
25. MULTI-MEDIA CARD (MMC) / SD CARD SLOT
Support MP3 ID3 format music only.
* IMPORTANT INFORMATION:
BECAUSE OF THE GREAT VARIETY OF PRODUCTS WITH USB, SD AND MMC CARD PORTS AND
THEIR SOMETIMES QUITE MANUFACTURER-SPECIFIC FUNCTIONS WE CAN NEITHER GUARAN-
TEE THAT ALL DEVICES WILL BE RECOGNIZED NOR THAT ALL OPERATING OPTIONS THAT ARE
POSSIBLE IN THEORY WILL ACTUALLY WORK
26. RESET
Reset button is placed on the housing.
The reset button is to be activated for the following reason:
Initial installation of the unit when all wiring is completed.
All the function button do not operate.
Error symbol on the display.
27. POWER INDICATOR LED
Flash LED when ignition is switched on.
26 27
RESET
E9
TECHNICAL SPECIFICATIONS
CD/MP3/WMA PLAYER SECTION
Signal to Noise Ratio > 60 dB
Channel Separation > 50 dB (1kHz)
Frequency Response 20Hz - 20 kHz
TUNER (FM)
Frequency range 87.5-108 MHz
Intermediate frequency 10.7 MHz
Sensitivity 2.8 µV
Stereo separation 30 dB
Signal to noise ratio 50 dB
Channel step 50 kHz
LINE-OUT
Output 350mV
Impedance 10k Ohm
LINE-IN
Frequency Response 20 Hz - 20 kHz
Sensitivity 775 mV
Impedance 20k Ohm
GENERAL
Power Supply 12V DC (10.8-15.6V allowable)
Speaker impedance 4 or 8 Ohm
Output power 40W x 4CH
Fuse 10A
Note: Specification and the design are subject to possible modification without notice due to improvements.
Instructions on environment protection
Do not dispose of this product in the usual household garbage at the end of its lifecycle; hand it over at a collection
point for the recycling of electrical and electronic appliances. The symbol on the product, the instructions for use or
the packing will inform about the methods for disposal.
The materials are recyclable as mentioned in this marking. By recycling, material recycling or other forms of re-utilization
of old appliances, you are making an important contribution to protect our environment.
Please inquire at the community administration for the authorized disposal location.
ALL RIGHTS RESERVED
COPY RIGHT DENVER ELECTRONICS A/S
www.denver-electronics.com
e 13
022680
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Denver CAD-490 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Denver CAD-490 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,24 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Denver CAD-490

Denver CAD-490 Gebruiksaanwijzing - Deutsch - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info