6
ENGLISH
@0 HEADPHONE mode button
• In the STEREO mode, this button feeds
STEREO Program and Cue to both earcups, in
the MONO mode, the Headphone circuit
provides MONO Cue to the left ear and
MONO Program to the right.
• In the STEREO mode, the meter indicates the
stereo level in the LEFT and RIGHT Main
Outputs. In the MONO mode, mono CUE level
is displayed on the Left meter and mono
PROGRAM level is displayed on the Right
meter.
• In the MONO mode, the adjacent green
indicator lights.
@1 HEADPHONE PAN control
• Serves two purposes…In the STEREO mode it
changes the relative levels of the Cue and
Program mixed together in both earcups. In
the MONO mode it changes the balance
between the Mono Cue in the left ear cup and
the Mono Program in the right.
@2 CUE buttons
• Pressing in any or all of the CUE buttons
routes the respective Source to the
Headphone and Meter Cue sections. Pressing
multiple buttons makes it possible to derive
mixed sound from the selected sources. The
adjacent red indicator illuminates when the
button is depressed.
@3 CROSSFADE ASSIGN A, B switches
• Assigns the Crossfader to any of the four Input
Channels and Off.
OFF
Select when not using the crossfader.
1 to 4
Select what channels (CH-1 to CH-4) to assign
to A and B.
Channels not assigned to A or B are output
without passing through the crossfader.
@4 CROSSFADER
• Controls the relative output level from the
summed A and B Mixes. When the fader is at
its far left, only the A Mix is heard from the
Outputs. As the fader is moved toward the
right, the amount of B Mix is increased and the
amount of A Mix is decreased. When the fader
is centered, equal amounts of A and B Mixes
are routed to the Outputs. Fully right is all B
Mix at the Outputs.
@5 CROSSFADER CONTOUR control
• Allows adjusting the “shape” of the
Crossfader response from a gentle curve for
smooth, long running fades, to the steep pitch
required for top performance cut and scratch
effects.
@6 CROSSFADER START A, B buttons
• The function to start the performance of CD
Player with Crossfader automatically is turned
on/off.
• When the button is pressed in, the Crossfader
Start is on and the adjacent orange indicator
lights.
@7 CH. FADER START switches
• This function will start the performance of CD
Player with Ch. fader automatically is turned
on/off.
@8 POWER indicator
• When the green indicator is lit, the DN-X400 is
ready to go.
(2) Rear Panel
@9
POWER switch
• Press the switch to turn the power on.
#0 MAIN OUT (BALANCED) connectors
• These XLR type connectors provide a
balanced line level output.
• Connect these connectors to the balanced
analog input connectors on an amplifier or
console.
• Pin layout 1. Common 2. Hot 3. Cold
• Applicable connector:
Cannon XLR-3-31 or equivalent.
NOTE:
Do not short-circuit the hot or cold pin with the
common pin.
#1 MAIN OUT (UNBALANCED) jacks
• This stereo pair of RCA jacks provide a
unbalanced line level output.
• Connect these jacks to the unbalanced analog
input jacks on an amplifier or console.
#2 DIGITAL OUT (COAXIAL) jack
• These RCA jacks provide a digital output data.
The signal is unaffected by the Master Level
fader.
• We recommend using a 75Ω/ohm RCA cord
for best digital transfer. (available from any
audio/video retailer)
#3 DIGITAL OUT (OPTICAL) jack
• The signal is unaffected by the Master Level
fader.
#4 BOOTH/ZONE OUT jacks
• These 1/4” jacks provide a balanced line level
output with independent front panel
Booth/Zone Level controls and are not
affected by the Master Level control.
• Connect these jacks to the balanced analog
input jacks on an amplifier or console.
#5 SUBWOOFER output jack
• This 1/4” mono jacks provide a mono line level
output of Main Out. The signal is affected by
the Master Level fader.
• Connect this jacks to the subwoofer input jack
on an amplifier.
#6 SUBWOOFER frequency control
• Adjusts the cut off frequency of the low pass
filter 40 Hz to 200 Hz.
• The low adjustment, will effect the Subwoofer
output.
#7 REC OUT jacks
• This stereo pair of RCA jacks provide a line
level output. The signal is unaffected by the
Master Level fader.
• It is intended for use with a tape recorder, but
is not restricted to that purpose.
#8 EFFECT jacks
• These 1/4” stereo jacks allow stereo external
processing of the Program signal.
• These are switching jacks --- always complete
the loop when connecting a send and return,
or no sound will be heard.
#9 LINE 1, 2, 3, 4, 6, 8 input jacks
• These stereo pairs of unbalanced RCA jacks
are Inputs for any line level device.
$0 Ch 1, 2 FADER output jacks
• Connect these jacks to the Fader input jacks of
the DN-1800F, the DN-2100F and the DN-
2600F using the 3.5 mm stereo mini cord.
$1 PHONO 1, 2 / LINE 5, 7 input jacks
• These stereo pairs of unbalanced RCA jacks
are Inputs for a Phono (RIAA) stage for
magnetic (MM) cartridges or a Line stage
suitable for any device, such as a CD player.
$2 PHONO 1, 2 / LINE 5, 7 switches
• These switches change the Input from Phono
to a Line level inputs.
• These switches set a Line level inputs when
Turntable is not connected.
$3 Phono Ground screw
• This screws provide a place to connect the
ground wire from a turntable.
This terminal is exclusively for a turntable
grounding and not a safety earth ground.
$4 MAIN MIC input jack
• Accepts a balanced microphone with 1/4”
jacks.
$5 AUX MIC input jack
• Accepts a balanced microphone with 1/4”
jacks.
