498717
12
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
This screen is not displayed when not using a subwoofer.
Set the crossover frequency and subwoofer mode according to the speaker system being used.
When using in combination with the SYS-550SD, we recommend turning the DSW-3Ls LF DIRECT switch on
and setting the AVR-550SDs crossover frequency to 150 Hz. (See page 37.)
12
ENGLISH
Setting the type of speakers
1
Set whether or not speakers are connected and, if so, their size parameters.
To select the speaker
1 FRNT Small
2
Press the (down) button to enter the settings and switch to the
SUBWOOFER MODE setting.
Set up in function of your speaker systems. Performing this setup optimizes the system.
The composition of the signals output to the different channels and the frequency response are adjusted
automatically according to the combination of speakers actually being used.
Center Sp. Front Sp.Front Sp.
Listening position
Surround back Sp.
Subwoofer
Surround Sp.
Surround Sp.
To select the parameter
Parameters
Large…… Select this when using speakers that can fully reproduce low sounds of below 80 Hz.
Small…… Select this when using speakers that cannot reproduce low sounds of below 80 Hz with sufficient
volume. When this setting is selected, low frequencies of below 80 Hz are assigned to the
subwoofer. (Example: SC-A3L, SC-C3L)
None…… Select this when no speakers are installed.
Yes/No. Select Yes when a subwoofer is installed, No when its not installed.
About the surround back speaker
When S.Back. Sp. is selected, the speaker systems change as described below.
When NONE is selected ..................................................................5.1ch speaker system
When Large or Small is selected and 1Speaker is selected ....6.1ch speaker system
The surround back audio signals are output from both the speaker terminals and the PRE OUT connectors
left channel. Connect one of these. A separate, commercially available pre-main (power) amplifier is
needed to connect the PRE OUT connector.
When 2 speaker is selected ............................................................7.1ch speaker system
The surround back audio signals are only output from the PRE OUT connector. Connect a commercially
available pre-main (power) amplifier to output the audio signals. No sound is output from the Surr. Back
speaker terminals.
NOTE:
Select Large or Small not according to the physical size of the speaker, but according to the bass
reproduction capacity at 80 Hz. If you cannot determine the best setting, try comparing the sound when set to
Small and when set to Large, at a level that will not damage the speakers.
Caution:
In case the subwoofer is not used, be sure to set Subwoofer = No, or the bass sound of front channel is
divided to subwoofer channel and not reproduced in some mode.
If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when
Small is set for the front, center and surround speakers.
For the majority of speaker system configurations, using the Small setting for all five main speakers and
Subwooofer On with a connected subwoofer will yield the best results.
Setting the Subwoofer mode and Crossover Frequency
1
Select the Subwoofer
Mode.
Select the setting.
6 MODE NORM
2
Select the Crossover
Frequency mode.
Select the frequency.
7 C R . OVER 15 0
3
Press the ENTER button to enter the setting and switch to the DELAY TIME
setting.
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Denon AVR-550SD bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Denon AVR-550SD in de taal/talen: Duits als bijlage per email.

De handleiding is 10,07 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info