571793
63
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
Note: The XM Radio ID does not use the letters “I”, “O”, “S” or
“F”. Activate your XM Satellite Radio service in the U.S. online at
http://activate.xmradio.com or call 1-800-XM-RADIO (1-800-967-
2346). Activate your XM Satellite Radio service in Canada online at
https:// activate.xmradio.ca or call 1-877-GET-XMSR (1-877-438-9677).
You will need a major credit card. XM will send a signal from the
satellites to activate the full channel lineup. Activation normally takes
10 to 15 minutes, but during peak busy periods you may need to keep
your XM Ready home audio system on for up to an hour. When you
can access the full lineup on your XM Ready home audio system you
are done.
1
Either turn <SOURCE SELECT> or press [SAT TU]
(AMP mode) to select “XM”.
1
(AMP mode) to select “XM”.
: ”Source Select” (vpage 43)
2
To operate using the main remote control unit, set the
remote control unit to the TUNER ( ) mode.
(vpage 73 “Remote Control Unit Operations”)
3
Use [d f] to select the station.
When the station is tuned in, the name of the track and artist
are displayed.
The channel switches continuously when [d f] is pressed and held.
XM Radio stations can be preset using the same procedure as for
FM/AM stations (vpage 57, 58 “Presetting Radio Stations (Preset
Memory)” and “Listening to Preset Stations”).
The artist name, track name, category and reception level can be
checked by pressing <STATUS>.
The time for which the GUI menus are displayed can be set at
GUI menu “Manual Setup” “Option Setup” “GUI” “Tuner”
(vpage 40).
Basic Operation
Checking the XM Signal Strength and
Radio ID
1
Either turn <SOURCE SELECT> or press [SAT TU]
(AMP mode) to select “XM”.
2
Press <STATUS> until “SIGNAL” appears on the
display.
The display will switch as shown below, depending on the
reception conditions.
Display GUI Status
GOOD Signal strength is good
MARGINAL Signal strength is marginal
WEAK Signal strength is weak
NO No signal
3
Adjust the position of the antenna until “SIGNAL:
GOOD” is shown on the display.
4
Press <STATUS> until the station you want to check
(example: “XM001”) is displayed.
5
Press [d f] and select channel 0 (XM000).
The radio ID is shown on the display.
The strength of both the XM satellite and terrestrial signals can be
checked at GUI menu “Source Select” “XM” – “Antenna Aiming”
(vpage 47).
Radio ID
Accessing XM Radio Stations Directly
1
Press [SEARCH].
2
Press [NUMBER] then input the station’s channel.
Example: Accessing station “XM123”:
[1] [2] [3]
b If no button is pressed within several seconds, the station
automatically switches to the one whose number has been input.
3
Press ENTER to set that station.
Reception switches to the selected station.
“LOADING” is displayed while stations or data are being received.
“CH UNAVAILABLE“ is displayed if the selected channel is no longer
a part of the XM lineup.
“CH UNAUTHORIZED“ is displayed if the selected channel is not
permitted to receive.
“XM - - -” is displayed if the selected channel cannot be used.
Searching Categories
1
Press o p.
2
Use o p to select the category, then use ui to select
the desired station.
Channel category
0
Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting
AVPA1HDCIEU_0121.indd 63 2008/01/21 12:49:39
63

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Denon AVP-A1HDCI bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Denon AVP-A1HDCI in de taal/talen: Engels als bijlage per email.

De handleiding is 14,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Denon AVP-A1HDCI

Denon AVP-A1HDCI Snelstart handleiding - English - 2 pagina's

Denon AVP-A1HDCI Gebruiksaanwijzing - Espanõl - 128 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info