382575
27
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
ENGLISH
25
Proper hand position requires one hand on the side
front grip (k), with the other hand on the back
handle (m).
Switching On and Off (fi g. 1)
To run the tool, press the variable speed switch (a).
The pressure exerted on the variable speed switch
determines the tool speed.
To stop the tool, release the switch.
Always switch off the tool when work is finished and
before unplugging.
SETTING THE ELECTRONIC SAWING SPEED
(FIG. 1) - DW311
The speed control dial (b) can be used for advance
setting of the required range of speed.
Turn the electronic speed control dial to the required
level. The required setting depends on the thickness
and kind of material.
Use high speeds for sawing soft materials such as
wood. Use low speeds for sawing metal.
WARNING: After using the tool for
an extended period on low speed
settings, run it for approx. 3 minutes on
maximum no-load speed.
Cutting Wood
1. Clamp the workpiece securely and remove all
nails and metal objects.
2. Holding the tool with both hands, work with the
saw shoe pressed against the workpiece.
Plunge Cutting in Wood (fi g. 5)
1. Rest the saw shoe on the workpiece in such
a position that the blade forms an appropriate
angle for the plunge cut.
2. Switch the tool on and slowly feed in the blade.
Make sure that the saw shoe remains in contact
with the workpiece at all times.
Pocket Cuts
1. Measure and mark the required pocket cut.
2. Using a narrow saw blade rest the bottom of
the saw shoe on the workpiece and make sure
that the blade is positioned on the cutting line.
If necessary, e.g. in confined spaces, use the
outer edge of the saw shoe as your guideline.
3. Switch on the tool and feed the blade into the
material at full speed, holding the tool firmly
against the workpiece.
Cutting Metal
When cutting thin metal always stabilize the
workpiece with wood on both sides. This guarantees
clean cuts and prevents damaging of the material.
For long, straight cuts draw a line on the workpiece.
Apply a thin film of lubricant along the cutting line,
switch on the tool and follow the cutting line.
Cutting Plastics
Always work at reduced speed. Carry out a test cut
to check whether the material is sensitive to heat.
Cutting Masonry
WARNING: When sawing asbestos
cement hazardous dust may be
produced. Follow the statutory
guidelines and observe the
recommendations issued by the
asbestos cement manufacturers.
Sawing Up to a Projecting Edge
(fi g. 6)
Using a conventional blade installed upside down,
cut up to the projected edge.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set-ups or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can
cause injury.
Dust Extraction
When the tool is used indoor for extended periods
of time, use a suitable dust extractor designed in
compliance with the applicable Directives regarding
dust emission.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt dw310k bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt dw310k in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 2,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info