390565
24
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
24
Remove both screws (12) from the diamond
guard and disassemble the front plate (13).
Insert the spindle through the hole in the rear
plate (14) and tighten the three screws (10).
Make sure the slots (15) in the rear plate and the
retention disc (16) coincide.
Rotate the angle grinder to the required position
and tighten the lock nut (11).
Fit an appropriate diamond cutting disc (see below).
Mount the front plate (13). Make sure that the dust
extraction outlet (17) is properly caught in the
opening between front (13) and rear plate (14).
Hook the cam behind the ruler stop (18) in the base
plate to make sure the spring (19) can move freely.
Refit the screws (12).
To remove the diamond guard, proceed in
reverse order.
Fitting and removing a grinding wheel or cutting
disc (fig. D)
Place the tool on a table, guard up.
Fit the spacer (20) correctly onto the spindle (5).
Place the grinding wheel or cutting disc on the
spacer.
Screw the threaded flange (21) onto the spindle (5).
Press the spindle lock (4) and rotate the grinding
wheel or cutting disc until it locks in position.
Tighten the threaded flange (21) with the two-pin
spanner supplied.
Release the spindle lock.
To remove the grinding wheel or cutting disc,
loosen the threaded flange (21) with the two-pin
spanner.
Fitting a wire cup brush
Screw the wire cup brush directly onto the
spindle without the use of the spacer and
threaded flange.
Mounting the side handle (fig. E)
For grinding, screw the side handle (6) tightly into
one of the holes (8) on either side of the gear case.
For cutting, screw the side handle (6) tightly into
the top hole (7).
DW491 + DE8501 - Mounting the round handle
DE8502 (option) (fig. F)
Remove the side handle.
ENGLISH
Conductor size (mm2) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
230 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Voltage drops
Inrush currents cause short-time voltage drops.
Under unfavourable power supply conditions, other
equipment may be affected.
If the system impedance of the power supply is lower
than 0.25 ø, disturbances are unlikely to occur.
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Mounting and removing the guard (fig. B)
Place the angle grinder on a table, spindle up.
Mount the guard to the tool using the three
screws (10) with star washers.
Rotate the guard to the required position and
tighten the lock nut (11).
To remove the guard, loosen the three screws (10).
DW491 - Mounting and removing the diamond
guard DE8501 (option) (fig. C)
The diamond guard DE8501 has been designed for
depth adjustment and efficient dust extraction.
Remove the guard from the angle grinder and
place the tool on a table, spindle up.
DWLAG.P65 17-09-2001, 08:4924
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt dw 490 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt dw 490 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 0,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt dw 490

DeWalt dw 490 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Espanõl, Polski, Türkiye, Dansk, Svenska, Norsk, Suomi - 79 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info