388889
30
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
30
E N G L I S H
Hammer drilling (fig. A)
Drilling with a solid bit
● Set the mode selector switch (3) to the
"hammer drilling" position.
● Insert the appropriate drill bit. For best results
use high quality carbide-tipped bits.
● Adjust the side handle (9) as required.
● If necessary, set the drilling depth.
● Mark the spot where the hole is to be drilled.
● Place the drill bit on the spot and switch on the
tool.
● Always switch off the tool when work is finished
and before unplugging.
Drilling with a core bit
● Set the mode selector (3) to the "hammer
drilling" position.
● Adjust the side handle (9) as required.
● Insert the appropriate core bit.
● Assemble the centerdrill into the core bit.
● Place the centerdrill on the spot and press the
variable speed switch (1). Drill until the core
penetrates into the concrete approx. 1 cm.
● Stop drilling and remove the centerdrill. Place the
core bit back into the hole and continue drilling.
● When drilling through a structure thicker than
the depth of the core bit, break away the round
cylinder of concrete or core inside the bit at
regular intervals. To avoid unwanted breaking
away of concrete around the hole, first drill a
hole the diameter of the centerdrill completely
through the structure. Then drill the cored hole
halfway from each side.
● Always switch off the tool when work is finished
and before unplugging.
Rotary drilling (fig. A)
● Set the mode selector switch (3) to the "rotary
drilling" position.
● Depending on your tool, follow either of the
following instructions:
- Fit the chuck adapter/chuck assembly
(D25313K).
- Replace the tool holder with the chuck
(D25314K).
● Proceed as described for hammer drilling.
@
Never use standard chucks in the
hammer drilling mode.
Screwdriving (fig. A)
● Set the mode selector switch (3) to the "rotary
drilling" position.
● Select the direction of rotation.
● Depending on your tool, follow either of the
following instructions:
- Insert the special SDS-plus® screwdriving
adaptor for use with hexagonal screwdriver
bits (D25313K).
- Replace the tool holder with the chuck
(D25314K).
● Insert the appropriate screwdriver bit. When
driving slotted head screws always use bits with
a finder sleeve.
● Gently press the variable speed switch (1) to
prevent damage to the screw head. In reverse
(LH) rotation the tool speed is automatically
reduced for easy screw removal.
● When the screw is flush with the workpiece,
release the variable speed switch to prevent the
screw head from penetrating into the workpiece.
Chipping and chiselling (fig. A)
● Set the mode selector switch (3) to the
"hammering only" position.
● Insert the appropriate chisel and rotate it by
hand to lock it into one of 51 positions.
● Adjust the side handle (9) as required.
● Switch on the tool and start working.
● Always switch off the tool when work is finished
and before unplugging.
&
Do not use this tool to mix or pump
easily combustible or explosive fluids
(benzine, alcohol, etc.).
Do not mix or stir inflammable liquids
labelled accordingly.
Optional accessories
Various types of SDS-plus
®
drill bits and chisels
are available as an option.
Consult your dealer for further information on the
appropriate accessories.
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt d 25313 k bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt d 25313 k in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info