712337
45
Verklein
Vergroot
Pagina terug
1/208
Pagina verder
43
english
2. Depress spindle lock button and use a wrench
on the hub of the wire wheel or brush to tighten
the wheel.
3. To remove the wheel, reverse the
aboveprocedure.
NOTICE: Failure to properly seat the
wheel hub before turning the tool on may
result in damage to tool or wheel.
Fitting and Removing a
Backing Pad/Sanding Sheet (fig. 1)
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange(D).
3. Place the rubber backing pad correctly onto the
spindle(B).
4. Place the sanding sheet on the rubber
backingpad.
5. Screw the threaded clamp nut(E) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button(A) and rotate the
spindle(B) until it locks in position.
7. Tighten the threaded clamp nut(E) with the hex
key provided or a two pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut(E) with the hex key
provided or a two pin spanner.
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
Prior to Operation
Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
Be sure the inner and outer flange are mounted
correctly. Follow the instructions given in the
Grinding and Cutting Accessory Chart.
Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and
thetool.
Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad
for cracks, tear or excess wear, wire brush
for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage
or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
Fitting and Removing a Grinding or
Cutting Disc (fig. 1, 4, 5)
WARNING: Do not use a
damaged disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange(D) correctly onto the
spindle(B) (fig. 4).
3. Place the disc(P) on the backing flange(D).
When fitting a disc with a raised centre, make
sure that the raised centre(O) is facing the
backing flange(D).
4. Screw the threaded clamp nut(E) onto the
spindle(B) (fig. 5):
a. The ring on the threaded clamp nut(E) must
face towards the disc when fitting a grinding
disc (fig. 5A);
b. The ring on the threaded clamp nut(E)
must face away from the disc when fitting a
cutting disc (fig. 5B).
5. Press the spindle lock button(A) and rotate the
spindle(B) until it locks in position.
6. Tighten the threaded clamp nut(E) with the hex
key provided or a two pin spanner.
7. Release the spindle lock.
8. To remove the disc, loosen the threaded clamp
nut(E) with the hex key provided or a two pin
spanner.
NOTE: Edge grinding can be performed with
Type27 wheels designed and specified for this
purpose; 6 mm thick wheels are designed for
surface grinding while 3 mm wheels are designed
for edge grinding. Cutting can be performed by
using a cutting wheel and a Type 1 guard.
Mounting Wire Brushes
andWire Wheels
Wire cup brushes or wire wheels screw directly
on the grinder spindle without the use of flanges.
Use only wire brushes or wheels provided with a
M14threaded hub. A Type 27 guard is required
when using wire brushes and wheels.
CAUTION: Wear work gloves when
handling wire brushes and wheels.
They can become sharp.
CAUTION: Wheel or brush must not
touch guard when mounted or while
in use. Undetectable damage could
occur to the accessory, causing wires to
fragment from accessory wheel or cup.
1. Thread the wheel on the spindle by hand.
45

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DWE4120 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DWE4120 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 20,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info