500493
26
Verklein
Vergroot
Pagina terug
1/116
Pagina verder
ENGLISH
24
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Side Handle (fi g. 1)
WARNING: To reduce the risk of
personal injury, ALWAYS operate
the tool with the side handle properly
installed and tightened. Failure to do so
may result in the side handle slipping
during tool operation and subsequent
loss of control. Hold tool with both
hands to maximise control.
A side handle (c) is supplied with your drill. The side
handle clamps to the front of the gear case and can
be rotated 360 degrees to permit right- or left-hand
use.
After the side handle is rotated into position, it
should be pushed rearward until the slots (h) on the
lip of the side handle are aligned and fully engaged
with the projecting tabs (i) on the underside of the
gear case. The side handle is then securely clamped
by turning clockwise until tight.
Variable Speed Trigger Switch (fi g. 2)
The variable speed trigger switch (a) permits speed
control. The farther the trigger switch is depressed,
the higher the speed of the drill.
NOTE: Use lower speeds for starting holes, drilling
in plastics or ceramics or driving screws.
Reversing Lever (fi g. 2)
The reversing lever (b), located above the trigger
switch, changes the direction of rotation of the drill
and is used when backing out screws and jammed
drill bits.
To operate the tool in reverse, release the trigger
switch and push the lever to the left (when viewed
from the chuck end).
To operate the drill in forward, release the trigger
switch and push the lever to the right (when viewed
from the chuck end).
Return the reversing lever to the forward position
after all operations in reverse are completed.
Torque Limiting Clutch
This tool is equipped with a torque limiting clutch
that reduces the maximum torque reaction
transmitted to the operator in case of jamming of a
drill bit. This feature also prevents the gearing and
electric motor from stalling. The torque limiting clutch
has been factory-set and cannot be adjusted.
Motor Lock Control (fi g. 1)
Your DEWALT drill comes with an electronic
feature called motor lock control. It is designed to
help prevent the motor from being overloaded in
demanding applications during a stall situation. This
may be encountered when drilling in steel or using
large bits in wood.
As a stall situation presents itself, the motor cycles
on and off for a set period of time. This reduces the
reaction of the stall. Releasing the trigger resets the
motor lock control and the unit will operate in normal
mode when the trigger is depressed again.
Figure 1 shows the instruction label (j) mounted on
the housing. There are two alert modes:
1. Engaged Mode: When a stall situation
presents itself, the light will come on and stay
on as the motor cycles on and off for a set
period of time before the motor lock control
completely shuts the tool down. When the unit
is running in normal mode, there will be no light
2. Problem Mode: A series of continual flashes as
the trigger is pulled indicates that the electronics
are no longer functioning. The tool may still be
able to function without the benefit of motor
lock control but should be serviced as soon as
possible.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: To reduce the risk of
personal injury, ALWAYS ensure
workpiece is anchored or clamped
firmly. If drilling thin material, use a wood
“back-up” block to prevent damage to
the material.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DWD221 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DWD221 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,98 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info