549313
27
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
20
ENGLISH
en - 5
Using an extension cable
An extension cord should not be used unless
absolutely necessary. Use an approved triple-core
extension cable suitable for the power input of your
charger (see technical data). The minimum conductor
size is 0.5 mm
2
; the maximum length is 30 m.
Assembly and adjustment
Prior to assembly and adjustment,
always remove the battery pack.
Always switch OFF the tool before
inserting or removing the battery pack.
Battery pack (fig. A)
Charging the battery pack
When charging the battery pack for the first time, or
after prolonged storage, it will only accept an 80%
charge. After several charge and discharge cycles,
the battery pack will attain full capacity.
Always check the mains prior to charging the battery
pack. If the mains is functioning but the battery pack
does not charge, take your charger to an authorised
DEWALT repair agent. Whilst charging, the charger
and the battery pack may become warm to touch.
This is a normal condition and does not indicate a
problem.
Do not charge the battery pack at
ambient temperatures <4 °C or >40 °C.
Recommended charging temperature:
approx. 24 °C.
To charge the battery pack (8), insert it into the
charger (10) as shown and plug in the charger.
Be sure that the battery pack is fully seated in the
charger. The red charging indicator (11) will blink.
After approx. 1 hour, it will stop blinking and
remain on. The battery pack is now fully charged.
The battery pack can be removed at any time or
left in the connected charger indefinitely.
Inserting and removing the battery pack
Insert the battery pack into the pistol grip (7) until
it clicks in place.
To remove the battery pack, press the two
release buttons (9) simultaneously and pull the
pack out of the pistol grip (7).
Inserting and removing a bit (fig. A & B)
This DEWALT Cordless Power Tool is equipped with
a bit compartment (6).
Open the chuck by turning the sleeve (12)
counterclockwise and insert the bit shank.
Tighten firmly by turning the sleeve clockwise
while holding the rear part of the chuck with one
hand.
To remove the bit, proceed in reverse order.
DW976 & DW996 - Selecting the operating mode
(fig. C)
The percussion drills can be used in two operating
modes:
Drilling: for steel, wood and plastics.
Percussion drilling: simultaneous rotating
and impacting for concrete and masonry
drilling operations.
Select the required operating mode by aligning
the symbol on the mode selector (4) with the
arrow (13) on the housing.
Forward/Reverse slider (fig. D)
To select forward or reverse rotation, use the
forward/reverse slider (2) as shown (see arrows
on tool).
Always release the variable speed switch
and wait until the motor has come to a
complete standstill before changing the
direction of rotation.
Two gear selector (fig. C)
Your tool is fitted with a two gear selector (3) to vary
the speed/torque ratio.
1 low speed/high torque (drilling large holes or
driving large screws)
2 high speed/low torque (smaller holes, drilling in
wood)
For speed rates, refer to the technical data.
Always push the two gear selector
completely forward or completely back.
Do not change gears at full speed or
during use.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW996 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW996 T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 0,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info