549658
23
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
18 en - 5
ENGLISH
Do not charge the battery pack at
ambient temperatures <4 °C or >40 °C.
Recommended charging temperature:
approx. 24 °C.
To charge the battery pack (6), insert it into the
charger (8) as shown and plug in the charger.
Be sure that the battery pack is fully seated in the
charger. The red charging indicator (9) will blink.
After approx. 1 hour, it will stop blinking and
remain on. The battery pack is now fully charged.
The battery pack can be removed at any time or
left in the connected charger indefinitely.
Inserting and removing the battery pack
Insert the battery pack into the grip until it clicks
in place.
To remove the battery pack, press the two
release buttons (7) simultaneously and pull the
pack out of the grip.
Inserting and removing bits (fig. A)
Open the chuck (4) by turning the sleeve (5)
counterclockwise and insert the bit shank.
Place the bit in the chuck as far as it will go and
lift slightly before tightening.
Tighten firmly by turning the sleeve clockwise
while holding the rear part of the chuck with one
hand.
To remove the bit, proceed in reverse order.
Forward/reverse switch (fig. A)
To select forward or reverse rotation, use the
forward/reverse slider (2) as shown (see arrows
on tool).
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Two gear selector (fig. B)
Your tool is fitted with a two gear selector (3) to vary
the speed/torque ratio.
1 low speed/high torque
(drilling large holes, driving large screws)
2 high speed/low torque
(drilling smaller holes, driving smaller screws)
For speed rates, refer to the technical data.
Always push the two gear selector
completely forward or backward.
Do not change gears at full speed or during use.
Removing and fitting the chuck (fig. C & D)
Open the chuck jaws as far as possible.
Insert a screwdriver into the chuck and remove
the chuck retaining screw (10) by turning
clockwise as shown in figure C.
Tighten an Allen key into the chuck and strike it with
a hammer as shown in figure D. This will loosen the
chuck so that it can be unscrewed by hand.
To refit the chuck, proceed in reverse order.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework and
wiring.
Apply only a gentle pressure to the tool.
Excessive force does not speed up
drilling but decreases tool performance
and may shorten tool life.
To minimise stalling on break-through,
progressively reduce the drill point
pressure towards the end of the
operation.
Keep the motor running when pulling the
bit back out of a drilled hole. This will
help prevent jamming.
Prior to operation:
Make sure your battery pack is (fully) charged.
Insert the appropriate bit.
Mark the spot where the hole is to be drilled.
Select forward or reverse rotation.
Switching ON and OFF (fig. A)
To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed
switch determines the tool speed.
To stop the tool, release the switch.
To lock the tool in OFF-position, move the
forward/reverse slider (2) to the central position.
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW955 T 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW955 T 2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 1,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info