546451
22
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
ENGLISH
20
7. Use the right tool.
Do not force small tools to do the job of a heavy duty tool. Do
not use tools for purposes not intended; for example do not use
circular saws to cut tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Non-skid footwear is recommended when working
outdoors. Wear protective hair covering to contain long hair.
9. Use protective equipment.
Always use safety glasses. Use a face or dust mask if working
operations create dust or flying particles. If these particles might
be considerably hot, also wear a heat-resistant apron. Wear ear
protection at all times. Wear a safety helmet at all times.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly
used.
11. Do not abuse the cord.
Never yank the cord to disconnect if from the socket. Keep the
cord away from heat, oil and sharp edges. Never carry the tool by
its own cord.
12. Secure work.
Where possible use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to operate the tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing
accessories. Inspect tools periodically and if damaged have them
repaired by an authorised service facility. Keep handles dry, clean
and free from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when changing accessories
such as blades, bits and cutters, disconnect tool from the power
supply.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that adjusting keys and
wrenches are removed from the tool before operating the tool.
17. Avoid unintentional starting.
Do not carry the tool with a finger on the switch. Be sure that the
tool is in the “off” position before plugging in.
18. Use outdoor extension leads.
Before use, inspect the extension cable and replace if damaged.
When the tool is used outdoors, use only extension cords intended
for outdoor use and marked accordingly.
19. Stay alert.
Watch what you are doing. Use common sense. Do not operate
the tool when you are tired or under the influence of drugs or
alcohol.
20. Check for damaged parts.
Before use, carefully check the tool and mains cable to determine
that it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions that may
affect its operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service centre
unless otherwise indicated in this instruction manual. Have any
damaged or defective switches replaced by an authorised service
center. Do not use the tool if the switch does not turn it on and off.
Never attempt any repairs yourself.
WARNING! The use of any accessory or attachment or
performance of any operation with this tool other than
those recommended in this instruction manual may present
a risk of personal injury.
21. Have your tool repaired by a qualified person.
This electric tool complies relevant safety rules. Repairs should
only be carried out by qualified persons using original spare parts;
otherwise this may result in considerable danger to the user.
Additional Safety Rules for Bandsaws
Before work checks that the machine is placed on an even surface
with sufficient stability.
In case of an accident or machine failure immediately turn the
machine off and disconnect from power supply.
Report the failure and mark the machine in suitable form to prevent
other people from using the defective machine.
When the saw blade is blocked caused by abnormal feed force
during cutting, switch the machine off and disconnect from power
supply. Remove the workpiece and ensure that the saw blade runs
free. Switch the machine on and start new cutting operation with
reduced feed force.
Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area while the machine is running.
Provide adequate general or localized lighting
Ensure the operator is adequately trained in the use, adjustment
and operation of the machine.
Connect the saw to a dust collection device when sawing wood.
Always consider factors which influence exposure of dust such as:
type of material to be machined (chip board produces more
dust than wood);
sharpness of the saw blade;
correct adjustment of the saw blade.
dust extractor with air velocity not less than 20 m/s.
Ensure that the local extraction as well as hoods, baffles and
chutes are properly adjusted.
Wear suitable personal protective equipment such as:
Hearing protection to reduce the risk of induced hearing loss.
Respiratory protection to produce the risk of inhalation of
harmful dust.
Gloves for handling the bandsaw blade and rough material.
When straight cutting against rip fence use the push stick.
Always place the guide (rip fence) on the lower side of the table
when cutting with the table inclined
When cutting round material use a suitable holding device to
prevent twisting of the workpiece.
Before starting operation check correct adjustment and functionality
of the band saw guards.
Workpiece sizes
Never cut workpiece shorter than 100mm.
Without additional support the machine is designed to accept
the maximum workpiece size of:
Height 150mm by width 230mm by length 700mm.
Longer workpiece needs to be supported by suitable
additional table.
This machine is not designed for serial or conveyor belt production.
Keep your hands well clear of the blade. Use a push stick for
narrow workpieces.
Ensure the blade rotates in the correct direction and the teeth are
pointing downwards.
Always use sharp blades of the correct type designed for the
workpiece.
Select the correct bandsaw blade for the different type of speed
settings and the material to be cut.
Observe the maximum speed marked on the bandsaw blade
packaging.
Do not use bandsaw blades that do not conform to the dimensions
stated in the technical data.
Do not use deformed or damaged bandsaw blades.
When performing bevel cuts, ensure that the rip fence is fixed on
the lower side of the table.
Keep the push stick in its place when not in use.
Keep the upper blade guard as close to the workpiece as possible.
When not in use, protect the saw blade completely using the blade
guard.
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW876 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW876 T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info