548692
8
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
4en - 4
ENGLISH
7 Top hole
8 Side holes
9 Carbon brush covers
Electrical safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 50144; therefore no
earth wire is required.
Using an extension cable
If an extension cable is required, use an approved
extension cable suitable for the power input of this
tool (see technical data). An undersized cable will
cause a drop in line voltage resulting in loss of
power and overheating.
When using a cable reel, always unwind the cable
completely.
Also refer to the table below.
Minimum gage for cable sets
Voltage Total cable length in feet
120 0-25 26-50 51-100 101-150
240 0-50 51-100 101-200 201-300
Ampere rating
More than Not more than AWG
0-6 18 16 16 14
6-10 18 16 14 12
10-12 16 16 14 12
12-16 14 12 not recommended
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Mounting and removing the guard (fig. B)
Place the Angle Grinder on a table, spindle up.
Mount the guard to the tool using the three
screws (10) with star washers.
Rotate the guard to the required position and
tighten the lock nut (11).
To remove the guard, loosen the three screws (10).
Fitting and removing a grinding wheel or cutting
disk (fig. C)
Place the tool on a table, guard up.
Fit the spacer (12) correctly onto the spindle (5).
Place the grinding wheel or cutting disk on the
spacer.
Screw the threaded flange (13) onto the spindle (5).
Press the spindle lock (4) and rotate the grinding
wheel or cutting disk until it locks in position.
Tighten the threaded flange (13) with the two-pin
spanner supplied.
Release the spindle lock.
To remove the grinding wheel or cutting disk,
loosen the threaded flange (13) with the two-pin
spanner.
Fitting a wire cup brush
Screw the wire cup brush directly onto the
spindle without the use of the spacer and
threaded flange.
Mounting the side handle (fig. D)
For grinding, screw the side handle (6) tightly into
one of the holes (8) on either side of the gear case.
For cutting, screw the side handle (6) tightly into
the top hole (7).
Instructions for use
Always observe the safety instructions
and applicable regulations.
Ensure all materials to be ground or cut
are secured in place.
Apply only a gentle pressure to the tool.
Do not exert side pressure on the
grinding wheel or cutting disk.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
Install the appropriate guard and disk or wheel.
Do not use excessively worn disks or wheels.
Be sure the spacer and threaded flange are
mounted correctly.
Make sure the disk or wheel rotates in the
direction of the arrows on the accessory and the
tool.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW852 T 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW852 T 2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info