548021
30
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
28
DW840 - Mounting (fig. B2 & C2)
Place the angle grinder on a table, spindle up.
Align the lugs (6) with the slots (7).
Press the guard (8) down and turn it in the
direction of the arrow (fig. B2).
Securely tighten the screws (9).
DW840 - Removing
To remove the guard, proceed in reverse order.
MOUNTING AND REMOVING A GRINDING WHEEL OR
CUTTING DISK (FIG. D & E)
Place the tool on a table, guard up.
Fit the spacer (11) correctly onto the spindle (10).
Place the grinding wheel or cutting disk on the
spacer.
Screw the threaded flange (12) onto the
spindle (10).
Press the spindle lock (5) and rotate the grinding
wheel or cutting disk until it locks in position.
Tighten the threaded flange using the two-pin
spanner (13) supplied.
Release the spindle lock.
To remove the grinding wheel or cutting disk,
loosen the threaded flange using the two-pin
spanner (while the spindle lock is engaged).
MOUNTING THE SIDE HANDLE (FIG. F)
Screw the side handle (3) tightly into one of the
holes (14) on either side of the gear case.
Instructions for use
WARNING:
Always observe the safety instructions
and applicable regulations.
Ensure all materials to be ground or cut
are secured in place.
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
grinding wheel or cutting disk.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Check that mounted wheels are
correctly fitted according to the
instructions given in this manual.
Ensure that blotters are used when they
are provided with the abrasive wheel
and when they are required.
Do not use separate reducing bushings
or adapters to adapt large hole abrasive
wheels.
Never use the tool without the guard in
place.
Be aware, the wheel continues to rotate
after the tools is switched off.
Prior to operation:
Install the appropriate guard and disk or wheel.
Do not use excessively worn disks or wheels.
Be sure the spacer and threaded flange are
mounted correctly.
Make sure the disk or wheel rotates in the
direction of the arrows on the accessory and the
tool.
Do not use cutting-off wheels for side grinding.
Ensure that sparks resulting from use do not
create hazard e.g. do not hit persons, or ignite
flammable substances.
OPERATION
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure
that the tool is off.
SWITCHING ON AND OFF (FIG. G)
CAUTION: Hold the side handle and
body of the tool firmly to maintain control
of the tool at start up and during use
and until the wheel or accessory stops
rotating. Make sure the wheel has come
to a complete stop be fore laying the tool
down.
To run the tool, press the lock-off button (2) and
the ON/OFF-switch (1). For continuous operation,
press the lock-on button (2) and release the
ON/OFF-switch.
To stop the tool, release the ON/OFF-switch.
To stop the tool in continuous operation, press
the ON/OFF-switch once more.
WARNING: Do not switch the tool ON or
OFF when under load.
ENGLISH
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW831 T 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW831 T 2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt DW831 T 2

DeWalt DW831 T 2 Aanvulling / aanpassing - Polski - 18 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info