546509
36
Verklein
Vergroot
Pagina terug
1/128
Pagina verder
ENGLISH
34
Blade Guard Assembly (fi g. 43)
The blade guard is a multifunctional assembly which offers the following
safety features:
Front guard (c) and spring-held rear guard (d) for full blade
protection.
Dust extraction adapter (a1).
Adjustable finger guard (a2) for use when cross-cutting.
BEVEL SCALE (FIG. 44)
Check that the bevel scale (u) reads 0˚ when positioned for a vertical
cut.
If required, loosen the screws (uu) and adjust the pointer to 0˚.
MITRE SCALE (FIG. 42)
Check that the mitre scale (yy) reads 0˚ when positioned for a vertical
cut.
Adjust the pointer (xx) to register 0˚ using the screw (zz).
The arm has preset positions at 45˚ left and right and at 0˚.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and applicable
regulations.
Ensure the material to be sawn is firmly secured in place.
Apply only a gentle pressure to the tool and do not exert
side pressure on the saw blade.
• Avoid overloading.
WARNING:
Install the appropriate saw blade. Do not use excessively
worn blades. The maximum rotation speed of the tool
must not exceed that of the saw blade.
• Do not attempt to cut excessively small pieces.
• Allow the blade to cut freely. Do not force.
• Allow the motor to reach full speed before cutting.
• Make sure all locking knobs and clamp handles are tight.
• Never run the machine without the guards in place.
• Never lift the machine by the table top.
• Always check that there is a suitable slot in the table top.
Always refer to figure L to check the fence position and
type.
The attention of UK users is drawn to the “woodworking machines
regulations 1974” and any subsequent amendments.
SWITCHING ON AND OFF (FIG. 1)
The on/off switch of your radial arm saw offers multiple advantages:
No-volt release function: should the power be shut off for
some reason, the switch has to be deliberately reactivated.
Motor overload protection device: in case of motor overload,
the power supply to the motor will be cut off. If this happens, let
the motor cool for 10 minutes and then press the reset button.
Braking system: after switching off, the braking system will
stop the saw blade within 10 seconds.
The switch has hold-to-run functions only.
To switch the machine on, press the green actuator (a) in the handle (b).
When the actuator is released the machine stops automatically.
MAKING A TRIAL CUT (FIG. 1)
1. With the mitre latch lever (j) engaged, lock the mitre clamp lever (k)
so that the blade is positioned for a straight 0° cross-cut.
2. Lower the arm until the blade almost touches the table top.
3. Place the workpiece against the front of the fence.
4. Switch on and lower the arm to allow the blade to cut a shallow
groove in the table surface.
5. Pull the blade towards you so that it cuts a vertical slot in the
wooden fence and through the workpiece.
6. Return the blade back to rest position and switch off.
7. Check that the cut is a true 90° in all planes and adjust if required.
Basic Saw Cuts (fi g. 45–53)
WARNING: The teeth of a new blade are very sharp and
can be dangerous.
CROSS-CUTTING (FIG. 45)
1. Set the radial arm at right angles to the fence.
2. Engage the mitre latch lever (j) in 0° position and tighten the mitre
clamp lever (k).
3. Lower the blade.
4. Adjust the finger guard (a2) so that it just clears the workpiece.
5. If there is no slot in the table top, cut one as described above.
6. Hold the workpiece against the fence, keeping your fingers well
away from the path of the blade.
7. Switch on and slowly pull the blade through the fence and the
workpiece.
8. Return the blade to rest position and switch off.
MITRE CUTS (FIG. 46, 47)
1. Release the mitre latch lever (j) and the mitre clamp lever (k).
2. Swing the arm to the required angle on the mitre scale.
3. For 45° left or right, engage the mitre latch lever (j) and lock with
the mitre clamp lever (k).
4. For intermediate angles, use the mitre clamp lever only.
5. Proceed as for cross-cutting.
BEVEL CUTS (FIG. 45, 48)
1. Set the arm as for a 0° cross-cut.
2. Raise the blade well above the table surface.
3. Release the bevel clamp lever (a3) and pull out the bevel latch (a4).
4. Tilt the motor to the required angle on the bevel scale (u).
5. For 45° right, engage the bevel latch (a4) and lock with the bevel
clamp lever (a3).
6. For intermediate angles, use the bevel clamp lever only.
7. Proceed as for a vertical cross-cut.
COMPOUND MITRE (FIG. 47)
This cut is a combination of a mitre and a bevel cut.
1. Set the required bevel angle.
2. Swing the arm to the required mitre position.
3. Proceed as for mitre cuts.
MAINTENANCE
Your DEWALT power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
NOTE: No service is needed on mechanical brake.
IMPORTANT: Replace the fixed table top and fence when worn.
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting or
changing set-ups or when making repairs. Be sure the
switch is in the OFF position. An accidental start-up can
cause injury.
WARNING: if the saw blade is worn replace it with a new
or re-sharpened blade.
Adjusting the Roller Head Bearings Arm Tracks
(fi g. 49–52)
If lateral movement is occurring in the roller head assembly, the bearings
need adjustment.
1. Pull the yoke assembly forward to the end of the arm tracks and
keep in position (fig. 49).
36

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW721KN bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW721KN in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info