546175
33
Verklein
Vergroot
Pagina terug
1/136
Pagina verder
31
ENGLISH
5. Tighten the blade locking screw (37) carefully by turning counter-
clockwise while holding the spindle lock engaged with your other hand.
WARNING! Be aware the saw blade shall be replaced in the
described way only. Only use saw blades as specified under
Technical Data; Cat. no.: DT4330 is suggested.
Adjustment
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs. Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
Your mitre saw was accurately adjusted at the factory. If readjustment due
to shipping and handling or any other reason is required, follow the steps
below to adjust your saw. Once made, these adjustments should remain
accurate.
Checking and adjusting the blade to the fence (fi g. E1 - E4)
Release the mitre lever (4) and depress the mitre latch (5) to release the
mitre arm (42).
Swing the mitre arm until the latch locates it at the 0° mitre position.
Do not tighten the lever.
Pull down the head until the blade just enters the saw kerf (43).
Place a square (44) against the left side of the fence (3) and blade (39)
(fi g. E3).
WARNING: Do not touch the tips of the blade teeth with the
square.
If adjustment is required, proceed as follows:
Loosen the screws (45) and move the scale/mitre arm assembly left or
right until the blade is at 90° to the fence as measured with the square.
Retighten the screws (45). Pay no attention to the reading of the mitre
pointer at this point.
Adjusting the mitre pointer (fi g. E1, E2 & F)
Release the mitre lever (4) and depress the mitre latch (5) to release the
mitre arm (42).
Move the mitre arm to set the mitre pointer (46) to the zero position,
as shown in fi g. F.
With the mitre lever loose, allow the mitre latch to snap into place as
you rotate the mitre arm past zero.
Observe the pointer (46) and mitre scale (7). If the pointer does not
indicate exactly zero, loosen the screw (47), move the pointer to read
0° and tighten the screw.
Mitre lock/detent rod adjustment (fi g. G)
If the base of the saw can be moved while the mitre lever (4) is locked,
the mitre lock/detent rod (48) must be adjusted.
Unlock the mitre lever (4).
Loosen the lock nut (61) on the miter lock rod.
Fully tighten the mitre lock/detent rod (48) using a screwdriver.
Then loosen the rod one turn.
Check that the table does not move when the lever (4) is locked at
a random (not preset) angle.
Tighten lock nut (61).
Checking and adjusting the blade to the table (fi g. H1 - H4)
Loosen the bevel clamp handle (21) and lift the bevel latch (20) to
release the saw arm.
Move the saw arm until the latch locates it at the 0° bevel position.
Do not tighten the handle.
Pull down the head until the blade just enters the saw kerf (43).
Place a set square (44) on the table and up against the blade (39) (fi g. H2).
WARNING: Do not touch the tips of the blade teeth with the
square.
If adjustment is required, proceed as follows:
Loosen the nuts (49, 55) and move the saw arm assembly left or right
until the blade is at 90° to the table as measured with the square.
Retighten the nut (49). The bevel angle requires adjustment after the
blade to table adjustment is complete.
Adjust the left and right bevel angles.
If the bevel pointer (50) does not indicate zero on the bevel scale (15),
loosen the screw (51) that secures the pointer and move the pointer as
necessary. Repeat as for the bevel pointer located on the opposite side.
Adjusting the fence (fi g. I1 & I2)
The upper part of the fence can be adjusted to provide clearance, allowing
the saw to bevel to a full 48° both left and right.
To adjust the left fence (3):
Loosen the plastic knob (52) and slide the fence to the left.
Make a dry run with the saw switched off and check for clearance.
Adjust the fence to be as close to the blade as practical to provide
maximum workpiece support, without interfering with the up and down
movement of the arm.
Tighten the knob securely.
To adjust the right fence (8):
Loosen the plastic knob (53) and slide the fence to the right.
Proceed as for adjusting the left fence.
WARNING: The guide grooves (54) can become clogged with
sawdust. Use a stick or some low pressure air to clear the guide
grooves.
Checking and adjusting the bevel angle (fi g. A2, I1, I2, J1 & J2)
Checking and adjusting the left bevel angle
Loosen the left side fence clamping knob (52) and slide the upper part
of the left side fence to the left as far as it will go.
Loosen the bevel clamp handle (21) and lift the bevel latch (20) to
release the saw arm.
Move the saw arm to the left until the latch locates it at the 45° bevel
position. Do not tighten the handle.
Check that the bevel indicator (50) indicates 45° on the bevel scale (15)
(fi g. J1).
If adjustment is required, proceed as follows:
Loosen the nut (55) and turn the stopscrew (56) in or out as necessary
until the pointer (50) indicates 45°. Retighten the nut (55).
To achieve a 50° bevel, turn the screw on the angle position stop out to
allow the saw arm to move as necessary.
Checking and adjusting the right bevel angle
Loosen the right side fence clamping knob (53) and slide the upper
part of the right side fence to the left as far as it will go.
Loosen the bevel clamp handle (21) and lift the bevel latch (20) to
release the saw arm.
Move the saw arm to the right until the latch locates it at the 45° bevel
position. Do not tighten the handle.
Check that the bevel indicator (50) indicates 45° on the bevel scale (15)
(fi g. J2).
If adjustment is required, proceed as for adjusting the left bevel angle.
Adjusting the bevel clamping system (fi g. K)
If the saw arm can be moved when the bevel clamp handle (21) is locked,
the clamping sytem must be adjusted.
Remove the screw (56) holding the handle.
Lift off the handle and turn it 1/8 turn clockwise. Refi t the screw.
Check that the saw arm does not move when the bevel clamp handle
(21) is locked at a random (not preset) angle.
33

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW718XPS T 4 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW718XPS T 4 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info