Handleiding DeWalt DW718 T 2 (pagina 34 van 128) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins)

546169

Verklein

Vergroot

Pagina terug

1/128

Pagina verder

ENGLISH

Cutting picture frames, shadow boxes & other four sided projects

(fig. Q1 & Q2)

Trim moulding and other frames

Try a few simple projects using scrap wood until you develop a “feel” for

your saw. Your saw is the perfect tool for mitring corners like the one

shown in fig. Q1. The joint shown has been made using either bevel

adjustment.

- Using bevel adjustment

The bevel for the two boards is adjusted to 45° each, producing a 90° corner.

The mitre arm is locked in the zero position. The wood is positioned with

the broad flat side against the table and the narrow edge against the fence.

- Using mitre adjustment

The same cut can be made by mitring right and left with the broad surface

against the fence.

The two sketches (fig. Q1 & Q2) are for four side objects only. As the

number of sides changes, so do the mitre and bevel angles. The chart

below gives the proper angles for a variety of shapes, assuming that all

sides are of equal length. For a shape that is not shown in the chart,

divide 180° by the number of sides to determine the mitre or bevel angle.

No. of sides Angle mitre or bevel

4 45°

5 36°

6 30°

7 25.7°

8 22.5°

9 20°

10 18°

Compound mitre (fig. R1 & R2)

A compound mitre is a cut made using a mitre angle (fig. Q2) and a bevel

angle (fig. Q1) at the same time. This is the type of cut used to make

frames or boxes with slanting sides like the one shown in fig. R1.

If the cutting angle varies from cut to cut, check that the bevel

clamp knob and the mitre lock knob are securely tightened.

These knobs must be tightened after making any changes in

bevel or mitre (fig. R1 & R2).

A compound mitre is a cut made using a mitre angle (fig. Q2) and a bevel

angle (fig. Q1) at the same time. This is the type of cut used to make

frames or boxes with slanting sides like the one shown in fig. R1.

If the cutting angle varies from cut to cut, check that the bevel

clamp knob and the mitre lock knob are securely tightened.

These knobs must be tightened after making any changes in

bevel or mitre.

• The chart shown below will assist you in selecting the proper bevel and

mitre settings for common compound mitre cuts. To use the chart,

select the desired angle “A” (fig. R2) of your project and locate that

angle on the appropriate arc in the chart. From that point follow the

chart straight down to find the correct bevel angle and straight across

to find the correct mitre angle.

• Set your saw to the prescribed angles and make a few trial cuts.

• Practice fitting the cut pieces together.

• Example: To make a 4 sided box with 25° exterior angles (angle “A”)

(fig. R2), use the upper right arc. Find 25° on the arc scale. Follow the

horizontal intersecting line to either side to get the mitre angle setting

on the saw (23°). Likewise follow the vertical intersecting line to the top

or bottom to get the bevel angle setting on the saw (40°). Always try

cuts on a few scrap pieces of wood to verify the settings on the saw.

Cutting base mouldings

The cutting of base moulding is performed at a 45° bevel angle.

• Always make a dry run without power before making any cuts.

• All cuts are made with the back of the moulding laying flat on the saw.

Inside corner

- Left side

• Position the moulding with top of the moulding against the fence.

• Save the left side of the cut.

- Right side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the left side of the cut.

Outside corner

- Left side

• Position the moulding with the bottom of the moulding against the

fence.

• Save the right side of the cut.

- Right side

• Position the moulding with top of the moulding against the fence.

• Save the right side of the cut.

Cutting crown mouldings

The cutting of crown moulding is performed in a compound mitre. In order

to achieve extreme accuracy, your saw has pre-set angle positions at

31.62° mitre and 33.85° bevel. These settings are for standard crown

mouldings with 52° angles at the top and 38° angles at the bottom.

• Make test cuts using scrap material before doing the final cuts.

• All cuts are made in a left bevel and with the back of the moulding

against the base.

Inside corner

- Left side

• Top of the moulding against the fence.

• Mitre right.

• Save the left side of the cut.

SET THIS BEVEL ANGLE ON SAW

SET THIS MITER ANGLE ON SAW

ANGLE OF SIDE OF BOX (ANGLE"A")

SQUARE BOX

6 SIDED BOX

8 SIDED BOX

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

DeWalt DW718 T 2 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info