546157
30
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
28
4. Keep other persons away.
Do not let persons, especially children, not involved in the work, touch
the tool or the extension cord and keep them away from the work area.
5. Store idle tools.
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate to which it was intended.
7. Use the right tool.
Do not force small tools to do the job of a heavy duty tool. Do not use
tools for purposes not intended; for example do not use circular saws
to cut tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Non-skid footwear is recommended when working
outdoors. Wear protective hair covering to contain long hair.
9. Use protective equipment.
Always use safety glasses. Use a face or dust mask if working
operations create dust or flying particles. If these particles might be
considerably hot, also wear a heat-resistant apron. Wear ear protection
at all times. Wear a safety helmet at all times.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust extraction and
collecting equipment, ensure these are connected and properly used.
11. Do not abuse the cord.
Never yank the cord to disconnect it from the socket. Keep the
cord away from heat, oil and sharp edges. Never carry the tool by its
cord.
12. Secure work.
Where possible use clamps or a vice to hold the work. It is safer than
using your hand and it frees both hands to operate the tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect
tools periodically and if damaged have them repaired by an authorized
service facility. Keep handles and switches dry, clean and free from oil
and grease.
15. Disconnect tools.
When not in use, before servicing and when changing accessories such
as blades, bits and cutters, disconnect tools from the power supply.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that adjusting keys and wrenches are
removed from the tool before operating the tool.
17. Avoid unintentional starting.
Do not carry the tool with a finger on the switch. Be sure that the tool is
in the “off” position before plugging in.
18. Use outdoor extension leads.
Before use, inspect the extension cable and replace if damaged.
When the tool is used outdoors, use only extension cords intended for
outdoor use and marked accordingly.
19. Stay alert.
Watch what you are doing. Use common sense. Do not operate the tool
when you are tired or under the influence of drugs or alcohol.
20. Check for damaged parts.
Before use, carefully check the tool and mains cable to determine
that it will operate properly and perform its intended function. Check
for alignment of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly repaired or
replaced by an authorized service centre unless otherwise indicated
in this instruction manual. Have defective switches replaced by an
authorized service centre. Do not use the tool if the switch does not
turn it on and off. Never attempt any repairs yourself.
WARNING! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
21. Have your tool repaired by a qualified person.
This electric tool complies relevant safety rules. Repairs should only be
carried out by qualified persons using original spare parts; otherwise this
may result in considerable danger to the user.
Additional Safety Rules for Mitre Saws
The machine is provided with a special configured power supply cord
which can only be replaced by the manufacturer or its authorised
service agent.
Do not use the saw to cut other materials than those recommended by
the manufacturer.
Do not operate the machine without guards in position, or if guards do
not function or are not maintained properly.
Ensure that the arm is securely fixed when performing bevel cuts.
Keep the floor area around the machine level, well-maintained and free
of loose materials, e.g., chips and cut-offs.
Use correctly sharpened saw blades. Observe the maximum speed
mark on the saw blade.
Make sure all locking knobs and clamp handles are tight before starting
any operation.
Never place either hand in the blade area when the saw is connected to
the electrical power source.
Never attempt to stop a machine in motion rapidly by jamming a tool or
other means against the blade; serious accidents can occur.
Before using any accessory consult the instruction manual.
The improper use of an accessory can cause damage.
Use a holder or wear gloves when handling a saw blade.
Ensure that the saw blade is mounted correctly before use.
Make sure that the blade rotates in the correct direction.
Do not use blades of larger or smaller diameter than recommended. For
the proper blade rating refer to the technical data. Use only the blades
specified in this manual, complying with EN 847-1.
Consider applying specially designed noise-reduction blades.
Do not use HSS blades.
Do not use cracked or damaged saw blades.
Do not use any abrasive discs.
Never use your saw without the kerf plate.
Raise the blade from the kerf in the workpiece prior to releasing the switch.
Do not wedge anything against the fan to hold the motor shaft.
The blade guard on your saw will automatically raise when the arm is
brought down; it will lower over the blade when head lock up release
lever (11) is pushed.
Never raise the blade guard manually unless the saw is switched off.
The guard can be raised by hand when installing or removing saw
blades or for inspection of the saw.
Check periodically that the motor air slots are clean and free of chips.
Replace the kerf plate when worn.
Disconnect the machine from the mains before carrying out any
maintenance work or when changing the blade.
Never perform any cleaning or maintenance work when the machine is
still running and the head is not in the rest position.
When possible, always mount the machine to a bench.
If you use a laser to indicate the cutting line, make sure that the laser is
of class 2 according to EN 60825-1. Do not replace a laser diode with
a different type. If damaged, have the laser repaired by an authorised
repair agent.
The front section of the guard is louvered for visibility while cutting.
Although the louvers dramatically reduce flying debris, they are
openings in the guard and safety glasses should be worn at all times
when viewing through the louvers.
ENGLISH
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW716 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW716 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info