545016
26
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
ENGLISH
24
Safety Instructions
When using stationary power tools, always observe the safety
regulations applicable in your country to reduce the risk of fire,
electric shock and personal injury.
Read all of this manual carefully before operating the tool.
Save this manual for future reference.
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose the tool to rain. Do not use the tool in damp or wet
conditions. Keep the work area well lit (250 - 300 Lux). Do not use
the tool where there is a risk of causing fire or explosion, e.g. in the
presence of flammable liquids and gases.
3 Keep children away
Do not allow children, visitors or animals to come near the work
area or to touch the tool or the mains cable.
4 Dress properly
Do not wear loose clothing or jewellery, as these can be caught in
moving parts. Wear protective hair covering to keep long hair out of
the way. When working outdoors, preferably wear suitable gloves
and non-slip footwear.
5 Personal protection
Always use safety glasses. Use a face or dust mask whenever the
operations may produce dust or flying particles. If these particles
might be considerably hot, also wear a heat-resistant apron. Wear
ear protection at all times.
6 Guard against electric shock
Prevent body contact with earthed surfaces (e.g. pipes, radiators,
cookers and refrigerators). When using the tool under extreme
conditions (e.g. high humidity, when metal swarf is being produced,
etc.), electric safety can be improved by inserting an isolating
transformer or a (FI) earth-leakage circuit-breaker.
7 Do not overreach
Keep proper footing and balance at all times.
8 Stay alert
Watch what you are doing.
Use common sense. Do not operate the tool when you are tired.
9 Secure workpiece
Use clamps or a vice to hold the workpiece. It is safer and it frees
both hands to operate the tool.
10 Connect dust extraction equipment
If devices are provided for the connection of dust extraction and
collection facilities, ensure that these are connected and properly
used.
11 Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed from
the tool before operating the tool.
12 Extension cables
Before use, inspect the extension cable and replace if damaged.
When using the tool outdoors, only use extension cables intended
for outdoor use and marked accordingly.
13 Use appropriate tool
The intended use is described in this instruction manual. Do not
force small tools or attachments to do the job of a heavy-duty tool.
The tool will do the job better and safer at the rate for which it was
intended. Do not force the tool.
WARNING! The use of any accessory or attachment or
performance of any operation with this tool other than those
recommended in this instruction manual may present a risk of
personal injury.
14 Check for damaged parts
Before use, carefully check the tool and mains cable for damage.
Check for misalignment and seizure of moving parts, breakage of
parts, damage to guards and switches and any other conditions
that may affect its operation.
Ensure that the tool will operate properly and perform its intended
function. Do not use the tool if any part is damaged or defective.
Do not use the tool if the switch does not turn it on and off.
Have any damaged or defective parts replaced by an authorised
DEWALT repair agent. Never attempt any repairs yourself.
15 Unplug tool
Switch off and wait for the tool to come to a complete standstill
before leaving it unattended. Unplug the tool when not in use,
before changing any parts of the tools, accessories or attachments
and before servicing.
16 Avoid unintentional starting
Be sure that the tool is switched off before plugging in.
17 Do not abuse cord
Never pull the cord to disconnect from the socket. Keep the cord
away from heat, oil and sharp edges.
18 Store idle tools
When not in use, tools must be stored in a dry place and locked up
securely, out of reach of children.
19 Maintain tools with care
Keep the tools in good condition and clean for better and safer
performance. Follow the instructions for maintenance and changing
accessories. Keep all handles and switches dry, clean and free
from oil and grease.
20 Repairs
This tool is in accordance with the relevant safety regulations. Have
your tool repaired by an authorised D
EWALT repair agent. Repairs
should only be carried out by qualified persons using original spare
parts; otherwise this may result in considerable danger to the user.
Additional Safety Rules for Mitre Saws
Make sure all locking knobs and clamp handles are tight before
starting any operation.
Do not operate the machine without the guard in position, or if the
guard does not function or is not maintained properly.
Never use your saw without the kerf plate.
Never place either hand in the blade area when the saw is
connected to the electrical power source.
Never attempt to stop a machine in motion rapidly by jamming a
tool or other means against the blade; serious accidents can be
caused unintentionally in this way.
Before using any accessory consult the instruction manual. The
improper use of an accessory can cause damage.
Select the correct blade for the material to be cut.
Observe the maximum speed marked on the saw blade.
Use a holder or wear gloves when handling a saw blade.
Do not use blades of larger or smaller diameter than
recommended. For the proper blade rating refer to the technical
data. Use only the blades specified in this manual, complying with
EN 847-1.
Consider applying specially designed noise-reduction blades.
Do not use HSS blades.
Do not use cracked or damaged saw blades.
Do not use any abrasive discs.
Raise the blade from the kerf in the workpiece prior to releasing the
switch.
Ensure that the arm is securely fixed when performing bevel cuts.
Do not wedge anything against the fan to hold the motor shaft.
The blade guard on your saw will automatically raise when the arm
is brought down; it will lower over the blade when the arm is raised.
The guard can be raised by hand when installing or removing saw
blades or for inspection of the saw. Never raise the blade guard
manually unless the saw is switched off.
The front section of the guard is louvred for visibility while cutting.
Although the louvres dramatically reduce flying debris, there are
openings in the guard and safety glasses should be worn at all
times when viewing through the louvres.
Keep the surrounding area of the machine well maintained and free
of loose materials, e.g. chips and cut-offs.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW712 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW712 T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 5,57 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info