546190
27
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
ENGLISH
25
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Replacing and Centring the Sanding
Belt (fi g. 2, 3)
Your belt sander uses 100 x 570 mm sanding belts.
1. Place the tool on its side with the clamping lever
(l) upwards.
2. Pull the clamping lever (l) upwards and to the
right.
3. Remove the sanding belt (e).
4. Place a new sanding belt making sure that the
arrow on the inside of the sanding belt points in
the same direction as the arrow on the machine
when on the same side of the rollers.
5 Push the clamping lever back.
6. Switch the machine ON and turn the outer belt
centring knob (f) until the sanding belt is centred
on the roller (k).
WARNING: The sanding belt should
never project at the rear! The sanding
belt should be flush with the outer edge
of the sanding surface.
Setting the Electronic Speed Control
Dial (fi g. 1)
DW650E
Turn the speed control dial (b) to the desired
position. The higher the number, the higher the
belt speed.
Dust Extraction
DUSTBAG (FIG. 4)
1. Squeeze the spring (m) of the dustbag (g) and
release it between the fixing rings (n).
2. For efficient dust extraction empty the dustbag
when it is about one third full.
3. Remove the dustbag, open the zipper and
gently shake out the dustbag.
DUST EXTRACTION ADAPTOR
(FIG. 5)
Screw the dust extraction adaptor (h) onto the
outlet (o).
Whenever possible, connect a dust extraction device
designed in accordance with the relevant regulations
regarding dust emission.
WARNING: Do not use a dustbag or
vacuum extractor without proper spark
protection when sanding metal.
WARNING:
Do not sand magnesium!
Do not rough sand pure metal
surfaces.
OPERATION
Instructions for Use
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING:
Always observe the safety
instructions and applicable
regulations.
Make sure all materials to be sanded
are well secured.
Apply only a gentle pressure to the
workpiece.
Sanding (fi g. 1)
A guiding handle (i) has been provided for optimum
tool control when using the Belt Sander without the
stationary stand.
1. Start with the coarsest grit size.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW650 T 6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW650 T 6 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 5,41 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info