447144
26
Verklein
Vergroot
Pagina terug
1/88
Pagina verder
18
ENGLISH
en - 5
Push the bit down and turn it slightly until it fits
into the slots.
Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
To remove a bit pull back the tool holder locking
sleeve (9) and pull out the bit.
Fitting the side handle (fig. D)
The side handle (5) can be fitted to suit both RH-
and LH-users.
Always use the tool with the side handle
properly assembled.
Loosen the side handle.
For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
left.
For LH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the right.
Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. E)
Insert the required drill bit.
Slacken the side handle (5).
Fit the depth adjustment rod (6) through the hole
in the side handle clamp.
Adjust the drilling depth as shown.
Tighten the side handle.
Forward/Reverse-lever (fig. F)
Push the forward/reverse-lever (3) to the LH-side
for forward (RH) rotation. See arrows on tool.
Push the forward/reverse-lever (3) to the RH-side
for reverse (LH) rotation.
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Replacing the dust cover (fig. C)
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover
immediately.
Pull back the tool holder locking sleeve (9) and
pull the dust cover (7) off.
Fit the new dust cover.
Release the tool holder locking sleeve.
How to fit the Chuck Adapter & Chuck
Unplug the tool.
Screw the keyed chuck onto the threaded end of
the chuck adapter.
Insert the connected chuck and adapter in the
tool as though it were a standard SDS-plus
®
bit.
Always tighten the accessory into the keyed
chuck using all three holes.
To remove the chuck, proceed as for removing a
standard SDS-plus
®
bit.
Never use the keyed chuck in hammer
drilling mode.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework and
wiring.
Apply only a gentle pressure to the tool
(approx. 2-3 kg). Excessive force does
not speed up drilling but decreases tool
performance and may shorten tool life.
Do not drill or drive too deep to prevent
damage to the dust cover.
Switching ON and OFF (fig. A)
To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed
switch determines the tool speed.
If necessary, press the lock-on button (2) for
continuous operation and release the variable
speed switch. The lock-on button works only in
full speed, forward rotation.
To stop the tool, release the variable speed switch.
To stop the tool in continuous operation, press
the variable speed switch briefly and release it.
Always switch OFF the tool when work is finished
and before unplugging.
Hammer drilling (fig. A)
Select the hammer drilling mode (4).
Insert the appropriate SDS-plus
®
bit. For best
results use high quality carbide-tipped bits.
Mark the spot where the hole is to be drilled.
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW566KC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW566KC in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info