548704
22
Verklein
Vergroot
Pagina terug
1/79
Pagina verder
17
Fitting and removing a grinding wheel or cutting
disk (fig. D)
Place the tool on a table, guard up.
Fit the spacer (20) correctly onto the spindle (5).
Place the grinding wheel or cutting disk on the
spacer.
Screw the threaded flange (21) onto the spindle (5).
Press the spindle lock (4) and rotate the grinding
wheel or cutting disk until it locks in position.
Tighten the threaded flange (21) with the two-pin
spanner supplied.
Release the spindle lock.
To remove the grinding wheel or cutting disk, loosen
the threaded flange (21) with the two-pin spanner.
Fitting a wire cup brush
Screw the wire cup brush directly onto the
spindle without the use of the spacer and
threaded flange.
Mounting the side handle (fig. E)
For grinding, screw the side handle (6) tightly into
one of the holes (8) on either side of the gear case.
For cutting, screw the side handle (6) tightly into
the top hole (7).
DW491K - Mounting the round handle (fig. F)
Remove the side handle.
Mount the round handle (22) using the two
screws (23).
Fit one screw in the top hole (7) and the other in
one of the side holes (8).
Instructions for use
Always observe the safety instructions
and applicable regulations.
Ensure all materials to be ground or cut
are secured in place.
Apply only a gentle pressure to the tool.
Do not exert side pressure on the
grinding wheel or cutting disk.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
Install the appropriate guard and disk or wheel.
Do not use excessively worn disks or wheels.
Be sure the spacer and threaded flange are
mounted correctly.
Make sure the disk or wheel rotates in the direction
of the arrows on the accessory and the tool.
Switching ON and OFF (fig. A)
The ON/OFF-switch of your Angle Grinder is
equipped with an unlocking switch or a locking switch
for continuous operation.
(U.K. & France only) - ON/OFF-switch (1) with
unlocking switch (2)
To unlock the ON/OFF-switch, slide the unlocking
switch towards you.
To run the tool, press the ON/OFF-switch.
To stop the tool, release the ON/OFF-switch.
ON/OFF-switch (1) with locking switch (2a)
To run the tool, press the ON/OFF-switch. The
tool now runs in continuous operation.
To stop the tool, press the locking switch briefly,
and release the ON/OFF-switch.
Do not switch the tool ON or OFF when
under load.
DW491K - Using the Diamond guard (EZWS97)
(fig. C)
The Diamond guard is used for cutting concrete and
masonry, when accurate cutting depth adjustment or
dust extraction are required.
Mount the Diamond guard as described above.
Connect a dust extractor to the outlet (17).
Set the cutting depth using the ruler knob in the
front plate (13).
Observe the safety instructions applying
to diamond cutting disks.
Use a suitable diamond cutting disk
(check the data of the manufacturer).
The maximum rotation speed on the cutting
disk must not be lower than that of the tool.
Do not use cutting disks with a diameter
exceeding 230 mm.
Fire hazard! Do not use the dust
extractor when cutting metal!
Make sure that the dust extractor used is
suitable for the material to be cut and the
Diamond guard can be connected.
en - 5
ENGLISH
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW491K T 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW491K T 1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 0,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info