547678
20
Verklein
Vergroot
Pagina terug
1/82
Pagina verder
18
ENGLISH
en - 5
Voltage Amperes Cable rating (Amperes)
115 0-2.0 66 66 610
2.1 - 3.4 6 6 6 6 15 15
3.5 - 5.0 6 6 10 15 20 20
5.1 - 7.0 10 10 15 20 20 25
7.1 - 12.0 15 15 20 25 25 -
12.1 - 20.0 20 20 25 - - -
220/240 0 - 2.0 6 6 6 6 6 6
2.1 - 3.4 6 6 6 6 6 6
3.5 - 5.0 6 6 6 6 10 15
5.1 - 7.0 10 10 10 10 15 15
7.1 - 12.0 15 15 15 15 20 20
12.1 - 20.0 20 20 20 20 25 -
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Mounting and removing the guard (fig. B & C)
Mounting
Place the Angle Grinder on a table, spindle up.
Align the lug (8) with the slot (9) in the bracket.
Press the guard (5) down and turn it in the
direction of the arrow (fig. B).
The guard locking pin (10) prevents the
guard from coming loose.
Removing
Hold the tool in your hand.
Rotate the guard (5) in the direction of the arrow
(fig. C).
Use a screwdriver to press the locking pin (10) in
the slot.
Release the guard.
Mounting and removing a grinding wheel or
cutting disk (fig. D & E)
Place the tool on a table, guard up.
Fit the spacer (12) correctly onto the spindle (11).
Place the grinding wheel or cutting disk on the
spacer.
Screw the threaded flange (13) onto the spindle (11).
Press the spindle lock (6) and rotate the grinding
wheel or cutting disk until it locks in position.
Tighten the threaded flange using the two-pin
spanner (14) supplied.
Release the spindle lock.
To remove the grinding wheel or cutting disk,
loosen the threaded flange using the two-pin
spanner (while the spindle lock is engaged).
Fitting a wire cup brush
Screw the wire cup brush directly onto the
spindle without using the spacer and threaded
flange.
Mounting and removing the rubber backing pad
(fig. F)
The rubber backing pad is available as an option.
Remove the guard from the tool.
Press the backing pad (16) onto the spindle (11).
The spacer is not needed.
Position the abrasive disk (15) on the pad.
Screw the threaded flange (13) onto the spindle (11).
Press the spindle lock and rotate the pad until it
locks in position.
Tighten the threaded flange using the two-pin
spanner supplied.
Release the spindle lock.
To remove the pad, loosen the threaded flange
using the two-pin spanner (while the spindle lock
is engaged).
Mounting the side handle (fig. H)
Screw the side handle (4) tightly into one of the
holes (17) on either side of the gear case.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Ensure all materials to be ground or cut
are secured in place.
Apply only a gentle pressure to the tool.
Do not exert side pressure on the
grinding wheel or cutting disk.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Prior to operation:
Install the appropriate guard and disk or wheel.
Do not use excessively worn disks or wheels.
Be sure the spacer and threaded flange are
mounted correctly.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW448 T 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW448 T 1 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 0,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info