548891
23
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
18 en - 5
ENGLISH
To insert the accessory (e.g. a bit holder or
nutsetter) (7) push it into the holder (8) until it
snaps in place. Tap it lightly if required.
To remove the accessory pull it out of the holder
using a pair of pliers.
Reinstall the collar (4) by aligning the ribs (9) on
the inside of the collar (4) with the grooves (10) in
the clutch housing and snap the collar in place.
DW268K/DW269K (fig. A)
Pull the ball retainer (5) to the front and hold it.
Insert the accessory.
Release the ball retainer.
Replacing the bit tip (fig. B)
Simply pull out the bit tip (11). A pair of pliers may
be required.
DW263K/DW274K/DW274KN -
Setting the driving depth (fig. C)
The depth sensitive feature offers the following
advantages:
- the selected driving depth is repeatable for
structural integrity
- screws with sealing washers are driven correctly
so that no leaks occur
The driving depth is determined by the position of
the depth locator (5) in relation to the bit or socket.
The symbols on the collar indicate how to set the
driving depth.
Turn the collar clockwise to increase the driving
depth.
Turn the collar counterclockwise to decrease the
driving depth.
DW263K - When using a nutsetter
For screws with sealing washers, turn the
adjustment collar until the end of the nutsetter is
flush with the end of the depth locator.
If required, turn the collar until the nutsetter is
recessed approximately 2 mm into the depth
locator.
Also refer to the screw manufacturer’s
specifications for the proper sealing washer
settings in different applications.
Drive a screw into a waste piece and check the
distance between the washer and the material.
Turn the collar (4) counterclockwise or clockwise
to decrease or increase the driving depth as
required.
Drive another screw and readjust the collar (4)
until the desired setting is achieved.
DW263K - Replacing the depth locator (fig. D)
This model is supplied with two depth locators (5) to
accommodate different bits, holders, sockets and
adaptors.
Pull the collar assembly off the tool.
Hold the depth locator (5) and unscrew the collar (4).
Replace the depth locator (5).
To reassemble, proceed in reverse order.
DW268K/DW269K - Setting the torque (fig. A)
This model allows setting the torque for a wide
range of screws.
To increase the torque, turn the torque
adjustment collar (4) counterclockwise.
To decrease the torque, turn the torque
adjustment collar (4) clockwise.
Drive a screw into a waste piece and check if the
screw is properly fastened.
If the clutch ratchets unexpectedly (for example
when a wood knot is encountered),
simply increase the pressure on the tool.
Setting the direction of rotation (fig. E)
Select forward or reverse rotation using the
forward/reverse switch (3) (see arrows on tool).
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Screwdriving or nutsetting (fig. A)
Select the appropriate bit for the screw (or nut) to
be driven.
Select forward or reverse rotation as described
above.
For nutsetting (DW263K) always use the correct
depth locator (5).
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW274KN T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW274KN T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 0,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt DW274KN T 3

DeWalt DW274KN T 3 Aanvulling / aanpassing - Polski - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info