Handleiding DeWalt DW074 (pagina 30 van 136) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins)

790945

Verklein

Vergroot

Pagina terug

1/136

Pagina verder

ENGLISH

ASSEMBLY

Inserting and Removing the

Batteries (ﬁ g. 1)

NOTE: This tool is powered by two LR20 (D-size)

batteries.

INSTALLING THE BATTERY PACK

1. Lift up the battery compartment cover (a) as

shown in Figure 1.

2. Insert two fresh LR20 (D-size) batteries in

the battery compartment. Place the batteries

according to the embossed icon (b) inside of

the compartment.

Setting Up the Laser

The laser facilitates various set-ups, making it useful

for several applications.

MANUAL HEAD ROTATION (FIG. 1)

The laser is designed with a protective roll cage

around the rotary head (d) to prevent accidental

damage from work site activities. You can still

access the rotary head and manually direct the

beam to establish or transfer a mark.

WALL SET-UP (FIG. 2)

The wall mount is used for mounting the laser to a

wall track to aid in drop ceiling installation and other

specialty leveling projects.

CAUTION: Before attaching the laser

level to wall track or ceiling angle, be

sure that the track or angle is

properly secured.

1. Place the laser on the mounting base (l), aligning

the hole (u) on the bottom of the laser with the

hole (m) in the mounting base. Place rear rubber

foot into the base mounting slot (n). Turn the

mounting knob (o) to secure the laser.

2. With the wall mount measuring scale (p) facing

you, push the clamp lever (q) in to open the

clamp jaws (r).

3. Position the clamp jaws (r) around the wall track

or ceiling angle and release the clamp lever (q)

to close the clamp jaws on the track. Be sure

that the wall mount is secure before proceeding.

CAUTION: Always use a ceiling wire

hanger or equivalent material, in addition

to the wall mount clamp locking knob,

to help secure the laser level while

mounting it to a wall. Thread the wire

through the handle of the laser level.

DO NOT thread the wire through the

protective roll cage. Additionally, screws

may be used to fasten the wall mount

directly to the wall as a back-up. A

screw hole (s) is located at the top of

the wall mount.

4. The tool can be adjusted up and down to the

desired offset height for working. To change

the height, loosen the locking knob (t), located

on the side of the wall mount, to move the

laser level up and down to the desired height.

Support the mounting base when adjusting

the height.

5. Use the wall mount measuring scale (p) to

pinpoint your mark.

NOTE: The DEWALT target card is marked at

38 mm (1-1/2"), therefore, it may be easiest

to set the offset of the laser to 38 mm (1-1/2")

below the track.

6. Once you have positioned the laser at the

desired height, tighten the locking knob (t) to

maintain this position.

TRIPOD SET-UP (FIG. 3)

1. Position the tripod securely and set it to the

desired height.

2. Make sure that the top of the tripod is roughly

level. The laser will self-level only if the top of the

tripod is within ± 5˚ of level. If the laser is set up

too far out of level, it will beep when it reaches

the limit of its leveling range. No damage will be

done to the laser, but it will not operate in an

“out of level” condition.

3. Secure the laser to the tripod by screwing the

threaded knob (v) on the tripod into the female

thread (u) on the bottom of the laser.

NOTE: Be sure that the tripod you are working

with has a 5/8"–11 threaded screw to ensure

secure mounting.

4. Turn the laser on and adjust the rotation speed

and controls as desired.

FLOOR SET-UP (FIG. 4, 5)

The laser level can be positioned directly on the

floor for leveling and plumbing applications such as

framing walls.

1. Place the laser on a relatively smooth and level

surface where it will not be disturbed.

2. Position the laser for a level (fig. 5A) or plumb

(fig. 5B) setting as shown.

3. Turn the laser on and adjust the rotation speed

and controls as desired.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

DeWalt DW074 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info