446500
30
Verklein
Vergroot
Pagina terug
1/124
Pagina verder
ENGLISH
28
ASSEMBLY
Inserting and removing a bit
(fi g. 1, 4)
DW052, DW054, DW056
The tool uses 1/4" hex. drive system with locking
sleeve.
1. Pull the sleeve/tool holder (c) forward and
insert the bit into the sleeve as far as it will go.
Release the sleeve to secure the bit.
2. To remove the bit, pull sleeve forward and pull
the bit out firmly.
Fitting and removing sockets
(fi g. 1, 4)
DW053, DW055, DW057
The tool uses a 1/2" square drive system with detent
pin.
FITTING SOCKETS
1. Align the hole (j) in the side of the socket with
the detent pin (k) on the anvil.
2. Push the socket (l) onto the anvil/tool holder (c)
until it snaps into place. Tap it lightly if required.
REMOVING SOCKETS
Depress the detent pin (k) through the hole in the
socket and pull the socket off the anvil.
Forward/reverse slider (fi g. 3)
To select forward or reverse rotation, use the
forward/reverse slider (b) as shown (see arrows
on tool).
CAUTION: Always wait until the motor
has come to a complete stand still
before changing the direction of rotation.
The first time the tool is run after changing the
direction of rotation, a click may be heard on
start up.
Instructions for use
WARNING: Always observe the safety
instructions and applicable regulations.
Prior to operation, make sure your battery pack is
(fully) charged.
OPERATION
WARNING: Turn unit off and disconnect
battery pack before installing and
removing accessories, before adjusting
or when making repairs. Lock the trigger
switch when the tool is not in use and
when storing the tool.
Prior to operation
1. Depending on your tool, select the appropriate
bit or socket.
2. To run the tool, press the variable speed switch
(a). The pressure exerted on the variable speed
switch determines the tool speed.
3. To lock the tool in off position, move the
forward/reverse slider (b) to the central position.
To Operate
1. Select forward or reverse rotation using slider
(b).
2. Depending on the application, follow either of
the below instructions.
3. Press the variable speed switch (a).
4. After tightening, check torque with a torque
wrench.
Screwdriving
1. Place the tip of the driver bit in the screw head.
2. Keeping the tool in line with the screw, apply
forward pressure to the tool as it contacts the
work surface.
Nutsetting
1. Place the socket over the head of the bolt or
nut.
2. Hold the tool in line with the fastener.
Tightening time
This tool tightens most fasteners in few seconds.
The proper tightening time in relation to torque must
be determined by experience.
WARNING: Excessive tightening may
damage the tip of the driver bit and the
head of the screw.
Use only dedicated impact accessories with your
tool. Consult your dealer for further information on
the appropriate accessories.
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW055 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW055 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 11,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info