78334
30
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
ENGLISH
28
1. Adjust the depth of cut as described above.
2. Set the fine adjuster to zero using the ring (x).
3. Rotate the fine adjuster (q) to the required
position: one turn corresponds to approximately
1 mm and 1 mark to 0.1 mm.
Depth Adjustment with Router
INSTALLED IN INVERTED POSITION (FIG. 4)
1. Remove the depth stop (m) and replace it with
the depth stop (DE6956) available as an option.
2. Connect the threaded rod of the depth stop (m)
to the revolver depth stop (l).
3. Set the depth of cut using the adjuster on the
depth stop (m).
WARNING: For installing the router in
inverted position, refer to the relevant
instruction manual on the stationary tool.
Fitting the Parallel Fence (fi g. 1, 5)
1. Fit the guide rods (e) to the router base (j).
2. Tighten the locking bolts (i).
3. Slide the parallel fence (h) over the rods.
4. Tighten the locking bolts (d) temporarily.
5. Remove the dust extraction adaptor (r) and
close the outlet using the dust extraction plug
(y) supplied with the tool.
Adjusting the Parallel Fence (fi g. 6)
1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in
contact with the workpiece.
3. Tighten the plunge limiter (o).
4. Position the router on the cutting line.
5. Slide the parallel fence (h) against the workpiece
and tighten the locking bolts (d).
6. Adjust the parallel fence (h) using the fine
adjuster (g). The outer cutting edge of the cutter
must coincide with the cutting line.
7. Firmly tighten the end lock (t).
Fitting a Guide Bush (fi g. 7)
Together with a template, guide bushes play a
valuable part in cutting and shaping to a pattern.
Fit the guide bush (z) to the router base (j) using
the screws (aa) as shown.
Connecting a Dust Extractor
(fi g. 1, 5)
Connect a dust extractor hose to the dust extraction
adaptor (r) in the router carriage column or to the
dust extraction outlet in the parallel fence (f).
Prior to Operation
1. Check that the cutter is correctly installed in
the collet.
2. Select the optimal speed using the electronic
speed control dial.
3. Set the cutting depth.
4. Connect a dust extractor.
5. Make sure the plunge limiter is always locked
before switching on.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING: Always move your router as
indicated in figure 8 (outer edges/inner
edges).
Proper Hand Position (fi g. 11)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on either
plunge limiter (o).
Switching On and Off (fi g. 9)
The lock-on/lock-off switch (a) is located in the
handle on the right-hand side. The router is normally
locked in the off position.
30

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW 621 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW 621 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 2,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info