110227
27
Verklein
Vergroot
Pagina terug
1/120
Pagina verder
ENGLISH
25
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power
input of this tool (see technical data).The minimum
conductor size is 1.5 mm
2
; the maximum length is
30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Fitting the Side Handles (fi g. 2)
1. Put the tool on its side.
2. Carefully insert the top end of one of the side
handles (d) into the opening of the front handle
(c).
3. Turn the side handle until its bottom end
engages in the housing (j).
4. Tighten the fixing screw (m) with the hex key (i).
5. Repeat this procedure for the other side handle.
WARNING: Always operate the
tool with the side handles properly
assembled.
Replacing the Saw Blades
REMOVING THE SAW BLADES (FIG. 3)
1. Turn the tool upside down and remove the saw
blade guard (g).
2. Loosen both saw blade fixing screws (h) with
the hex key (i) until a click is heard.
3. Carefully pull one saw blade until the threaded
hole (n) is out of the housing.
4. Pull the saw blade out of the locking clip (o) and
take it out of the bar (f).
5. Repeat this procedure for the other saw blade.
FITTING THE SAW BLADES (FIG. 4)
1. Slide one saw blade into the bar (f) making sure
its slotted hole (p) fits into the locking clip (o).
2. Insert the back of the saw blade into the
housing (j) until the threaded hole (n) lodges in
the required mounting position.
3. Repeat this procedure for the other saw blade.
4. Using a piece of wood push on the toothed
side of the saw blades to make sure that they
are exactly parallel to the bar (f).
5. Tighten both saw blade fixing screws (h)
securely by pressing and turning simultaneously
with the short end of the Hex key (i).
WARNING: Before operation let the
saw blades run freely for approx. 20 s.
Saw Blades
Material Recommended Cat. #
saw blade
Low density
building block TCT saw blade DT2964
Medium density
building block TCT saw blade DT2966
Cellular concrete TCT saw blade DT2965
Prior to Operation (fi g. 1)
Remove the saw blade guard (g).
Mount the appropriate type of saw blade.
Check that the tool is running properly and can
perform all its functions. Make sure that the bar
(f) is still straight and the saw blades (e) and the
housing (j) are undamaged.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW 392 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW 392 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 3,89 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info