110161
32
Verklein
Vergroot
Pagina terug
1/132
Pagina verder
ENGLISH
30
For continuous operation, press and hold down
the switch (1), press the lock-on button (2) and
release the switch.
To stop the tool, release the switch.
To stop the tool in continuous operation, press
the switch briefly and release it. Always switch
off the tool when work is finished and before
unplugging.
DW333
Switching on: slide the on/off switch (1) to the front.
Switching off: slide the on/off switch to the rear.
Always switch off the tool when work is finished
and before unplugging.
Setting the electronic sawing speed
(fi g. G1 & G2)
DW331 (fig. G1)
The sawing speed varies with the pressure exerted
on the on/off switch (1).
To preset the sawing speed, turn the control dial
(3) to the desired level. The higher the rate, the
higher the sawing speed. The required setting
depends on the thickness and kind of material.
Use high speeds for sawing soft materials such
as wood. Use low speeds for sawing metal.
DW333 (fig. G2)
The speed control dial (3) can be used for advance
setting of the required range of speed.
Turn the electronic speed control dial to the
required level. The required setting depends on
the thickness and kind of material.
Use high speeds for sawing soft materials such
as wood. Use low speeds for sawing metal.
WARNING: After using the tool for
an extended period on low speed
settings, run it for approx. 3 minutes on
maximum no-load speed.
Sawing in wood
If necessary, draw a cutting line.
Switch the tool on.
Hold the tool against the workpiece and follow
the line.
For sawing parallel to the edge of your workpiece,
install the parallel fence and guide your jigsaw
along the workpiece a shown in figure H.
Sawing in wood using a pilot hole
If necessary, draw a cutting line.
Drill a hole (ø min. 12 mm) and introduce the saw
blade.
Switch the tool on.
Follow the line.
For cutting perfectly round shapes, install the
trammel bar and set it to the required radius (fig. I).
Sawing up to a projecting edge (fig. J)
Using a conventional blade, cut up to the
projected edge.
Finish off the cut using a flush cutting blade.
Dust extraction (fig. F)
When the tool is used indoor for extended
periods of time, use a suitable dust extractor
designed in compliance with the applicable
Directives regarding dust emission.
Sawing in metal
Mount an appropriate saw blade.
Proceed as described above.
WARNING: Use a cooling lubricant
(cutting oil) to prevent overheating of the
saw blade or the workpiece.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing
set-ups or when making repairs.
Be sure the trigger switch is in the OFF
position. An accidental start-up can
cause injury.
32

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DW 333 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DW 333 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,94 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info