790832
11
Verklein
Vergroot
Pagina terug
1/20
Pagina verder
9
ENGLISH
12 . Securework.
ʵ Where possible use clamps or a vice to hold the work. It is safer than using your hand and
it frees both hands to operate thetool.
13 . Do notoverreach.
ʵ Keep proper footing and balance at alltimes.
14 . Maintain tools withcare.
ʵ Keep cutting tools sharp and clean for better and safer performance. Follow instructions
for lubricating and changing accessories. Inspect tools periodically and if damaged have
them repaired by an authorized service facility. Keep handles and switches dry, clean and
free from oil andgrease.
15 . Disconnecttools.
ʵ When not in use, before servicing and when changing accessories such as blades, bits and
cutters, disconnect tools from the powersupply.
16 . Remove adjusting keys andwrenches.
ʵ Form the habit of checking to see that adjusting keys and wrenches are removed from the
tool before operating thetool.
17 . Avoid unintentionalstarting.
ʵ Do not carry the tool with a finger on the switch. Be sure that the tool is in the “off”
position before connecting to the powersupply.
18 . Use outdoor extensionleads.
ʵ Before use, inspect the extension cable and replace if damaged. When the tool is used
outdoors, use only extension cords intended for outdoor use and markedaccordingly.
19 . Stayalert.
ʵ Watch what you are doing. Use common sense. Do not operate the tool when you are
tired or under the influence of drugs oralcohol.
20 . Check for damagedparts.
ʵ Before use, carefully check the tool and power supply to determine that it will operate
properly and perform its intended function. Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting and any other conditions that may affect its
operation. A guard or other part that is damaged should be properly repaired or replaced
by an authorized service centre unless otherwise indicated in this instruction manual.
Have defective switches replaced by an authorized service centre. Do not use the tool if the
switch does not turn it on and off. Never attempt any repairsyourself.
WARNING! The use of any accessory or attachment or performance of any operation
with this tool other than those recommended in this instruction manual may present a
risk of personalinjury.
21 . Have your tool repaired by a qualifiedperson.
ʵ This electric tool complies with relevant safety rules. Repairs should only be carried out
by qualified persons using original spare parts; otherwise this may result in considerable
danger to theuser.
Additional Safety Rules for Mitre Saws
The machine is provided with a special configured power supply cord which can only be
replaced by the manufacturer or its authorised serviceagent.
Do not use the saw to cut other materials than those recommended by themanufacturer.
Do not operate the machine without guards in position, or if guards do not function or are not
maintainedproperly.
Ensure that the arm is securely fixed when performing bevelcuts.
Keep the floor area around the machine level, well-maintained and free of loose materials,
e.g., chips and cut-offs.
Use correctly sharpened saw blades. Observe the maximum speed mark on the sawblade.
Select the correct blade for the material to becut.
Make sure all locking knobs and clamp handles are tight before starting anyoperation.
Never place either hand in the blade area when the saw is connected to the electrical
powersource.
Do not reach behind the fence with either hand closer than 100mm from either side of
the saw blade, to remove wood scraps, or for any other reason while the blade is spinning.
The proximity of the spinning saw blade to your hand may not be obvious and you may be
seriouslyinjured.
Never attempt to stop a machine in motion rapidly by jamming a tool or other means against
the blade; serious accidents canoccur.
Before using any accessory consult the instruction manual. The improper use of an accessory
can causedamage.
Use a holder or wear gloves when handling a saw blade or roughmaterial.
Ensure that the saw blade is mounted correctly beforeuse.
Make sure that the blade rotates in the correctdirection.
Do not use blades of larger or smaller diameter than recommended. For the proper blade
rating refer to the technical data. Use only the blades specified in this manual, complying
with EN 847-1.
Do consider applying specially designed noise-reductionblades.
Do not use HIGH SPEED STEELblades.
Do not use cracked or damaged sawblades.
Do not use any abrasive or diamonddiscs.
Never use your saw without the kerfplate.
Before each cut ensure that the machine isstable.
Raise the blade from the kerf in the workpiece prior to releasing theswitch.
Do not wedge anything against the fan to hold the motorshaft.
The blade guard on your saw will automatically raise when the head up-lock release lever is
pushed and the arm is brought down; it will lower over the blade as the arm israised.
Never raise the blade guard manually unless the saw is switched off. The guard can be raised
by hand when installing or removing saw blades or for inspection of thesaw.
Check periodically that the motor air slots are clean and free ofchips.
Replace the kerf plate when worn. Refer to service parts listincluded.
Disconnect the machine from the mains before carrying out any maintenance work or when
changing theblade.
Never perform any cleaning or maintenance work when the machine is still running and the
head is not in the upperposition.
If you use an LED to indicate the cutting line, make sure that the LED is of class 2 according
to EN62471. Do not replace an LED diode with a different type. If damaged, have the LED
repaired by an authorised repairagent.
The front section of the guard is louvered for visibility while cutting. Although the louvers
dramatically reduce flying debris, they are openings in the guard and safety glasses should be
worn at all times when viewing through thelouvers.
Connect the saw to a dust collection device when sawing wood. Always consider factors
which influence exposure of dust such as:
ʵ type of material to be machined (chip board produces more dust than wood);
ʵ sharpness of the saw blade;
ʵ correct adjustment of the saw blade;
ʵ dust extractor with air velocity not less than 20m/s.
Ensure that the local extraction as well as hoods, baffles and chutes are properlyadjusted.
Please be aware of the following factors influencing exposure to noise:
ʵ use saw blades designed to reduce the emitted noise;
ʵ use only well sharpened sawblades.
Machine maintenance shall be conductedperiodically.
Provide adequate general or localizedlighting.
Ensure that any spacers and spindle rings are suitable for the purpose as stated in thismanual.
Refrain from removing any cut-offs or other parts of the workpiece from the cutting area while
the machine is running and the saw head is not in the upperposition.
Never cut workpieces shorter than 200mm.
Without additional support the machine is designed to accept the maximum workpiece size
for cross-cutting:
ʵ Maximum height: 112mm
ʵ Maximum width: 345mm
ʵ Maximum length: 600mm
ʵ Longer workpiece needs to be supported by suitable additional support, e.g. DE7023-XJ or
DE7033-XJ legstand. Always clamp the workpiecesafely.
In case of an accident or machine failure, immediately turn the machine off and disconnect
machine from the powersource.
Report the failure and mark the machine in suitable form to prevent other people from using
the defectivemachine.
When the saw blade is blocked due to abnormal feed force during cutting, turn the machine
off and disconnect it from power supply. Remove the workpiece and ensure that the saw
blade runs free. Turn the machine on and start new cutting operation with reduced feedforce.
Never cut light alloy, especiallymagnesium.
Whenever the situation allows, mount the machine to a bench using bolts with a diameter of
8 mm and 80 mm inlength.
Batteries
Chargers/Charge Times (Minutes)
Cat #
DC
Weight
Batteries Chargers/Charge Times (Minutes)
Cat # VDC Ah
Weight
kg DCB107 DCB113 DCB115 DCB118 DCB132 DCB119
DCB546 18/54 6.0/2.0 1.05 270 140 90 60 90 X
DCB547 18/54 9.0/3.0 1.25 420 220 140 85 140 X
DCB181 18 1.5 0.35 70 35 22 22 22 45
DCB182 18 4.0 0.61 185 100 60 60 60 120
DCB183/B 18 2.0 0.40 90 50 30 30 30 60
DCB184/B 18 5.0 0.62 240 120 75 75 75 150
DCB185 18 1.3 0.35 60 30 22 22 22 X
DCB187 18 3.0 0.48 140 70 45 45 45 90
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DHS780 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DHS780 in de taal/talen: Engels als bijlage per email.

De handleiding is 6.68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt DHS780

DeWalt DHS780 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Türkiye, Dansk, Svenska, Norsk, Suomi - 168 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info