546574
43
Verklein
Vergroot
Pagina terug
1/188
Pagina verder
ENGLISH
41
WARNING: To avoid being pinched,
keep hands away from the hinge when
changing positions.
The tool can be converted into three different
positions. To change positions, slide the pivot
release slider (c) to the right as shown in Figure6
and rotate the handle portion of the tool until it
snaps securely into any of the three positions shown
in Figure 7.
Blade Installation and Removal
(fi g.8, 9A, 9B, 9C)
WARNING: To reduce the risk
of serious personal injury, place
the lock-off button in the lock-
off position or turn tool off and
disconnect battery pack before
making any adjustments or
removing/installing attachments or
accessories. An accidental start-up
can cause injury.
Different blade lengths are available. Use the
appropriate blade for the application. The blade
should be longer than 3-1/2" (89 mm) and should
extend past the shoe and the thickness of the
workpiece during the cut. A 4" (102 mm) blade is
recommended for best performance. Do not use
jigsaw blades with this tool.
WARNING: Cut hazard. Blade breakage
may occur if the blade does not extend
past the shoe and the workpiece during
the cut (fig.8). Increased risk of personal
injury, as well as damage to the shoe
and workpiece may result.
TO INSTALL BLADE INTO SAW (FIG. 9A, 9B, 9C)
1. Pull blade clamp release lever (g) up.
2. Insert the blade shank into the blade clamp
(f,fig. 9C).
3. Close blade clamp release lever.
4. Note that the blade can be installed upside-
down to assist in flush-to cutting (refer to
fig.9B).
TO REMOVE BLADE FROM SAW (FIG. 9A, 9B, 9C)
CAUTION: Burn hazard. Do not touch
the blade immediately after use. Contact
with the blade may result in personal
injury.
1. Pull blade clamp release lever (g) up.
2. Remove blade.
Worklight (fi g. 9C)
The worklight (e) is located below the blade clamp
(f) behind the shoe. The worklight will be activated
when the trigger switch is squeezed.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Cutting (fi g. 9B, 10–13)
WARNING: Always use eye protection.
All users and bystanders must wear eye
protection that conforms to ANSI Z87.1.
WARNING: Exercise extra caution
when cutting towards operator. Always
hold saw firmly with both hands while
cutting.
Before cutting any type of material, be sure it is firmly
anchored or clamped to prevent slipping. Place
blade lightly against work to be cut, switch on saw
motor and allow it to obtain maximum speed before
applying pressure. Whenever possible, the saw shoe
must be held firmly against the material being cut.
This will prevent the saw from jumping or vibrating
and minimize blade breakage. Any cuts which put
pressure on the blade such as angle or scroll cuts
increase potential for vibration, kickback and blade
breakage.
WARNING: Use extra caution when
cutting overhead and pay particular
attention to overhead wires which may
be hidden from view. Anticipate the path
of falling branches and debris ahead of
time.
WARNING: Inspect work site for hidden
gas pipes, water pipes or electrical wires
before making blind or plunge cuts.
Failure to do so may result in explosion,
property damage, electric shock, and/or
serious personal injury.
FLUSH-TO CUTTING (FIG. 9B, 10)
The compact design of the saw motor housing and
spindle housing permits extremely close cutting to
floors, corners and other difficult areas. The blade
should be inserted upside-down to assist in flush-
cutting (fig.9B).
POCKET/PLUNGE CUTTING – WOOD ONLY (FIG. 11)
The initial step in pocket cutting is to measure the
surface area to be cut and mark clearly with a
pencil, chalk or scriber. Use the appropriate blade
for the application. The blade should be longer than
3-1/2" (89mm) and should extend past the shoe
and the thickness of the workpiece during the cut.
43

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DCS310 T 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DCS310 T 2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 20,03 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info