Handleiding DeWalt DCD735 T 1 (pagina 44 van 196) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins)

549241

Verklein

Vergroot

Pagina terug

1/196

Pagina verder

ENGLISH

Proper Hand Position (ﬁ g. 3)

WARNING: To reduce the risk of

serious personal injury, ALWAYS use

proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold

securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the top

of the drill (l) as shown, with the other hand on the

main handle (m).

Drill Operation (ﬁ g. 4)

WARNING: To reduce the risk of

serious personal injury, turn tool off and

disconnect tool from power source

before making any adjustments or

removing/installing attachments or

accessories.

WARNING: To reduce the risk of

personal injury, ALWAYS ensure

workpiece is anchored or clamped

firmly. If drilling thin material, use a wood

“back-up” block to prevent damage to

the material.

1. Turn the collar (c) to the drill symbol.

2. Select the desired speed/torque range using the

gear shifter to match the speed and torque to

the planned operation.

3. For WOOD, use twist bits, spade bits, power

auger bits or hole saws. For METAL, use high-

speed steel twist drill bits or hole saws. Use

a cutting lubricant when drilling metals. The

exceptions are cast iron and brass which should

be drilled dry.

4. Always apply pressure in a straight line with the

bit. Use enough pressure to keep drill biting, but

do not push hard enough to stall the motor or

deflect the bit.

5. Hold tool firmly with both hands to control

the twisting action of the drill. If model is not

equipped with side handle, grip drill with one

hand on the handle and one hand on the

battery pack.

CAUTION: Drill may stall if overloaded

causing a sudden twist. Always expect

the stall. Grip the drill firmly to control

the twisting action and avoid injury.

6. IF DRILL STALLS, it is usually because

it is being overloaded or improperly used.

RELEASE TRIGGER IMMEDIATELY, remove

drill bit from work, and determine cause of

stalling. DO NOT CLICK TRIGGER ON AND

OFF IN AN ATTEMPT TO START A STALLED

DRILL — THIS CAN DAMAGE THE DRILL.

7. To minimize stalling or breaking through the

material, reduce pressure on drill and ease the

bit through the last fractional part of the hole.

8. Keep the motor running when pulling the bit

back out of a drilled hole. This will help prevent

jamming.

9. With variable speed drills there is no need to

center punch the point to be drilled. Use a

slow speed to start the hole and accelerate by

squeezing the trigger harder when the hole is

deep enough to drill without the bit skipping

out.

Hammerdrill Operation (ﬁ g. 5)

1. Turn the collar (c) to the hammerdrill symbol.

2. Select the high speed setting by sliding the

selector back (away from the chuck).

IMPORTANT: Use carbide-tipped or masonry

bits only.

3. Drill with just enough force on the hammer to

keep it from bouncing excessively or “rising” off

the bit. Too much force will cause slower drilling

speeds, overheating and lower drilling rate.

4. Drill straight, keeping the bit at a right angle to

the work. Do not exert side pressure on the bit

when drillling as this will cause clogging of the

bit flutes and a slower drilling speed.

5. When drilling deep holes, if the hammer speed

starts to drop off, pull the bit partially out of the

hole with tool stil running to help clear debris

from the hole.

NOTE: A smooth, even flow of dust from the hole

indicates proper drilling rate.

Screwdriver Operation (ﬁ g. 6)

1. Select the desired speed/torque range using the

dual range gear selector to match the speed

and torque of the planned operation.

2. Turn the torque adjustment collar (c) to the

desired position. Lower numbers indicate lower

torque settings; higher numbers indicate higher

torque settings.

3. Insert the desired fastener accessory into the

chuck as you would any drill bit.

4. Make some practice runs in scrap or on unseen

areas to determine the proper position of the

clutch collar.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

DeWalt DCD735 T 1 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van DeWalt DCD735 T 1

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info