627546
42
Verklein
Vergroot
Pagina terug
1/188
Pagina verder
40
english
some models, a hammer symbol. These numbers
are used to set the clutch to deliver a torque range.
The higher the number on the collar, the higher the
torque and the larger the fastener which can be
driven. To select any of the numbers, rotate until the
desired number aligns with the arrow.
Dual Range Gearing (Fig. 1)
The dual range feature of your drill/driver/hammerdrill
allows you to shift gears for greater versatility.
1. To select speed 1 (high torque setting), turn
the tool off and permit it to stop. Slide the gear
shifter (d) forward (towards the chuck).
2. To select speed 2 (low torque setting), turn the
tool off and permit it to stop. Slide the gear
shifter back (away from the chuck).
NOTE: Do not change gears when the tool is
running. Always allow the drill to come to a complete
stop before changing gears. If you are having trouble
changing gears, make sure that the dual range
gear shifter is either completely pushed forward or
completely pushed back.
Worklight (Fig. 1)
There is a worklight (e) located just above the
trigger switch (a). The worklight is activated when
the trigger switch is depressed. When the trigger is
released, the worklight will stay illuminated for up to
20 seconds.
NOTE: The worklight is for lighting the immediate
work surface and is not intended to be used as a
flashlight.
Keyless Single Sleeve Chuck
(Fig. 7–9)
WARNING: Do not attempt to tighten
drill bits (or any other accessory) by
gripping the front part of the chuck
and turning the tool on. Damage to
the chuck and personal injury may
result. Always lock off trigger switch
and disconnect tool from power source
when changing acces sories.
WARNING: Always ensure the bit
is secure before starting the tool. A
loose bit may eject from tool causing
possible personal injury.
Your tool features a keyless chuck (f) with one
rotating sleeve for one-handed operation of the
chuck. To insert a drill bit or other accessory, follow
these steps.
1. Turn tool off and disconnect tool from power
source.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 2)
Some D
e
WALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (k). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Variable Speed Trigger Switch (fig.1)
To turn the tool on, squeeze the trigger switch (a).
To turn the tool off, release the trigger switch. Your
tool is equipped with a brake. The chuck will stop as
soon as the trigger switch is fully released.
NOTE: Continuous use in variable speed range is
not recommended. It may damage the switch and
should be avoided.
Forward/Reverse Control Button
(Fig. 1)
A forward/reverse control button (b) determines the
direction of the tool and also serves as a lock-off
button.
To select forward rotation, release the trigger switch
and depress the forward/reverse control button on
the right side of the tool.
To select reverse, depress the forward/reverse
control button on the left side of the tool.
The center position of the control button locks
the tool in the off position. When changing the
position of the control button, be sure the trigger is
released.
NOTE: The first time the tool is run after changing
the direction of rotation, you may hear a click on
start up. This is normal and does not indicate a
problem.
Torque Adjustment Collar (Fig. 1)
Your tool has an adjustable torque screwdriver
mechanism for driving and removing a wide array of
fastener shapes and sizes and in some models, a
hammer mechanism for drilling into masonry. Circling
the collar (c) are numbers, a drill bit symbol, and on
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DCD731 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DCD731 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 16,06 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info