549074
26
Verklein
Vergroot
Pagina terug
1/108
Pagina verder
26
ENGLISH
Take off the protective cap (13) before placing
the battery pack (9) in the charger or tool.
Place the protective cap over the contacts
immediately after removing the battery pack from
the charger or tool.
Make sure the protective cap is in place
before storing or carrying a detached
battery pack.
Equalisation mode
The equalisation mode helps to maintain the
optimum capacity of the battery pack. It is therefore
recommended to use the equalisation mode weekly
or every 10 charge/discharge cycles.
Charge the battery pack as described above.
When the charging indicator stops blinking, leave
the battery in the charger for approx. 4 hours.
DE9116 - Hot Pack Delay
When the charger detects a battery that is hot,
it automatically starts a Hot Pack Delay, suspending
charging until the battery has cooled. After the
battery has cooled, the charger automatically
switches to the pack charging mode. This feature
ensures maximum battery life. The red indicator (12)
blinks long, then short while in the Hot Pack Delay
mode.
Inserting and removing bits (fig. A & C)
Open the chuck by turning the sleeve (14)
counterclockwise and insert the bit shank.
Place the bit in the chuck as far as it will go and
lift slightly before tightening.
Tighten firmly by turning the sleeve clockwise.
To remove the bit, proceed in reverse order.
Selecting the operating mode or adjusting the
torque (fig. D)
The collar of this tool has 17 positions for the
adjustment of the torque to suit the size of the screw
and the workpiece material. For torque adjustment,
refer to the section «Screwdriving».
Select the drilling mode or torque by aligning the
symbol or number on the collar (4) with the
indicator (15) on the housing.
Forward/reverse slider (fig. E)
To select forward or reverse rotation, use the
forward/reverse slider (2) as shown (see arrows
on tool).
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Two gear selector (fig. F)
Your tool is fitted with a two gear selector (3) to vary
the speed/torque ratio.
1 low speed/high torque
(drilling large holes, driving screws)
2 high speed/low torque
(drilling smaller holes)
For speed rates, refer to the technical data.
Always push the two gear selector
completely forward or backward.
Do not change gears at full speed or during use.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework and
wiring.
Apply only a gentle pressure to the tool.
Switching on and off (fig. A & E)
To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
To stop the tool, release the switch.
To lock the tool in the off position, move the
forward/reverse slider (2) to the central position.
The drill is equipped with a brake to stop
the tool as soon as the variable speed
switch is fully released.
Screwdriving (fig. A)
Select forward or reverse rotation using the slider
(2).
Set the collar (4) to position 1 and begin
screwdriving (low torque).
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DC757K T 10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DC757K T 10 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Spaans, Pools, Turks, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 0,8 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt DC757K T 10

DeWalt DC757K T 10 Aanvulling / aanpassing - English - 20 pagina's

DeWalt DC757K T 10 Aanvulling / aanpassing - Polski - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info