79260
46
Verklein
Vergroot
Pagina terug
1/204
Pagina verder
44
ENGLISH
CAUTION: Never use standard chucks
in the hammerdrilling mode.
Replacing the dust cover ( g. D)
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
Pull back the tool holder locking sleeve (15) and
pull the dust cover (7) off.
Fit the new dust cover.
Release the tool holder locking sleeve.
OPERATION
Instructions For Use
WARNING:
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework
and wiring.
Apply only a gentle pressure to the tool
(approx. 5 kg). Excessive force does
not speed up drilling but decreases tool
performance and may shorten tool life.
Do not drill or drive too deep to prevent
damage to the dust cover.
Always hold the tool rmly with both
hands and ensure a secure stance .
Always operate the tool with the side
handle properly mounted.
If the cutting tool is no longer sharp,
replace with a new cutting tool.
Prior to Operation:
Make sure your battery pack is (fully) charged.
Make sure the battery pack is properly seated.
Proper Hand Position (fi g. I)
WARNING: To reduce the risk of serious
personal injury, ALWAYS use proper
hand position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of a sudden reaction.
Proper hand position requires one hand on the side
handle (9), with the other hand on the main handle
(10).
To remove a bit pull back the tool holder locking
sleeve (15) and pull out the bit.
Fitting the side handle ( g. E)
The side handle (9) can be tted to suit both
right-hand and left-hand users.
WARNING: Do not use the tool without
the side handle properly assembled.
Loosen the side handle.
For RH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the left.
For LH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
Rotate the side handle to the desired position
and tighten the handle.
Setting the Drilling Depth ( g. F)
Insert the required drill bit.
Slacken the side handle (9).
Fit the depth adjustment rod (8) through the
hole in the side handle clamp.
Adjust the drilling depth as shown.
Tighten the side handle.
Forward/reverse Slider ( g. G)
Push the forward/reverse slider (2) to the LH-side
for forward (RH) rotation. See arrows on tool.
Push the forward/reverse slider (2) to the RH-
side for reverse (LH) rotation.
CAUTION: Always wait until the motor
has come to a complete standstill
before changing the direction of
rotation.
DC229, DC234 - Replacing the Tool Holder with
the Chuck ( g. H)
Turn the locking collar (6) into the unlocking
position and pull the tool holder (5) off.
Push the chuck (16) onto the spindle and turn
the locking collar into the locking position.
To replace the chuck with the tool holder, rst
remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
46

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt DC 228 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt DC 228 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 8,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt DC 228

DeWalt DC 228 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Türkiye, Dansk, Svenska, Norsk, Suomi - 168 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info