Handleiding DeWalt D51855 (pagina 26 van 132) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins)

546482

Verklein

Vergroot

Pagina terug

1/132

Pagina verder

ENGLISH

cannot be exceeded by more than 10%. In case

of higher pressures, a pressure reducing valve

including a downstream safety valve shall be

built into the compressed air supply.

• Only use hoses with a rating exceeding the

maximum operating pressure of the tool.

• To prevent an unnecessarily high noise level,

increased wear and resulting failures, the nailer

should be operated with the lowest pressure

required for the work process.

• DO NOT use oxygen, combustible gases

or any other reactive gases for operating

compressed air. Danger of explosion and/or

serious personal injury may result.

• Before transporting the tool, disconnect it from

the compressed air system, especially where

ladders are used or where unusual physical

posture is adopted while moving.

• Disconnect the tool from the air supply when it

is not in use.

• Avoid weakening or damaging the tool,

for example by:

– punching or engraving

– modifications not authorised by the

manufacturer

– guiding against templates made of hard

material such as steel

– dropping or pushing across the floor

– applying excessive force of any kind

• Do not use the equipment as a hammer.

WARNING! Keep the nailer, loaded or

unloaded, pointed away from yourself and

others. Serious personal injury may result.

• While working, hold the tool in such a way that

no injuries can be caused to the head or to the

body in the event of a possible recoil due to a

disruption in the energy supply or hard areas

within the workpiece.

• NEVER actuate the fastener driving tool into

free space.

• In the work area, carry the tool at the workplace

using only one handle, and NEVER with the

trigger actuated.

• Consider the conditions in the work area.

Fasteners can penetrate thin workpieces or slip

off corners and edges of the workpiece, and

thus put people at risk. The length of the nails

used should be no longer than the thickness of

the workpieces. If the nails are longer than the

workpiece thickness this could cause a rebound

of the nails if the workpiece is placed on a hard

surface, e.g., concrete, steel.

• Do not drive fasteners close to the edge of the

workpiece. ALWAYS keep a distance of at least

25 mm from the edge of the workpiece so nails

will not destroy the workpiece.

• Do not drive fasteners on top of other fasteners.

• Only use spare parts specified by the

manufacturer or his authorised agents.

• Have repairs carried out only by the

manufacturer or authorised agents having due

regard to the information given in the manual

and using the appropriate tools and equipment.

• Replacement of contact trip spring is

recommended every 3–4 years to ensure

personal safety.

• Do not disassemble or block any parts of the

fastener driving tool such as the safety yoke.

• Have the tool serviced properly and at regular

intervals.

• ALWAYS wear safety gloves to reduce the risk

of personal injuries.

Residual Risks

• The following risks are inherent to the use of

these machines:

– Injuries caused by improper handling of the

tool.

– Loss of control due to not gripping tool firmly.

– Muscle strain of arms and hands, especially

when working overhead. Always take regular

breaks when working for long periods of

time.

– Do not use the tool while you are tired

or under influence of drugs, alcohol or

medication. A moment of inattention while

operating may result in serious personal

injury.

• In spite of the application of the relevant

safety regulations and the implementation of

safety devices, certain residual risks cannot be

avoided. These are:

– Impairment of hearing. Under some

conditions and duration of use, noise from

this product may contribute to hearing loss.

– Loss of control caused by recoil.

– Risk of injury caused by pinch points, sharp

edges and improper handling of workpiece.

– Risk of injury caused by sharp edges when

changing nails or inserting nail sticks.

– Discomfort to hand and arms. Vibration

caused by the operating action of this tool

may cause permanent injury to fingers,

hands, and arms. Use gloves to provide

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

DeWalt D51855 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info