546463
23
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
23
ENGLISH
Instructions for use
Always observe the safety instructions
and applicable regulations.
Preparing the tool (fig. C)
Drain all condensation from the air compressor
tanks and hoses.
Lubricate the tool. See “Maintenance”.
Remove all nails from the magazine.
Lock the nail pusher (11) in the back position.
Check if the contact trip (3) and nail pusher (11)
can move freely.
Do not use the tool if the contact trip or
nail pusher cannot move freely.
Check that the pressure of the air supply is below
the maximum recommended operating pressure.
Connect the air hose to the fitting on the tool.
Check for audible leaks around valves and gaskets.
Never use a tool that leaks or has
damaged parts.
Cold weather operation
When operating tools at temperatures below freezing:
Keep the tool as warm as possible before use.
Disconnect the airline from the tool.
Put 5-10 drops of DEWALT pneumatic tool oil (or
winter-weight pneumatic oil containing ethylene
glycol) into the air inlet.
Set the air pressure to a maximum of 5.5 bar.
Connect the air hose to the fitting on the tool.
Load nails into the magazine as described below.
Actuate the tool 5 or 6 times into scrap lumber to
lubricate the o-rings.
Increase the air pressure to the normal operating
level.
Use the tool in the normal manner.
Hot weather operation
The tool should operate normally. Avoid the heat of
direct sunlight to avoid damage to the bumpers,
o-rings, and other rubber parts.
Loading the tool (fig. C)
These tools are equipped with a dual-load
magazine.
Always connect the tool to the air supply
before loading nails.
Select an appropriate collated nail stick. See
“Technical data”.
Load the magazine using one of the following
methods:
Loading and locking
Insert collated nail stick (s) into the loading slot in
the rear of the magazine.
Pull the nail pusher (11) rearward to fall behind
the nails.
Locking and loading
Lock the nail pusher (11) in the back position.
Insert collated nail stick (s) into the loading slot in
the rear of the magazine.
Unlatch the nail pusher by pushing forward and
carefully slide the nail pusher forward to press
against the nails.
Actuating the tool (fig. D)
These tools are equipped with a trigger/lock-off
switch (1). When rotated to the right, this switch
prevents the tool from actuating.
When the switch is centred, the tool will be fully
operational. The tool can be operated using one of
two modes: sequential action mode or bump action
mode. The trigger installed on the tool determines
the mode of actuation.
Sequential action mode
The sequential action mode is used for intermittent
nailing when very careful and accurate placement is
desired.
Fit the grey trigger as described above.
Push the contact trip against the work surface.
Pull the trigger to actuate the tool. Each trigger
pull with the contact trip pushed against the work
surface will drive one nail.
Bump action
The bump action mode is used for rapid nailing on
flat, stationary surfaces.
Fit the black trigger as described above.
To drive a single nail: Operate the tool as
described for sequential action.
D51256.P65 28-12-2001, 09:2123
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D51275K T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D51275K T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info