548823
10
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
ENGLISH
8
Spark Defl ector Adjustment (fi g. 1)
To best deflect sparks away from surrounding
persons and materials, loosen the screw (b), adjust
the spark deflector (c) and then retighten screw. Do
not allow cordset to come into contact with deflector
or sparks as damage to cordset may occur.
Depth Stop (fi g. 1)
Depth stop is set at the factory for a new 355mm
(14") wheel to prevent wheel from cutting into the
supporting surface. To allow more depth of cut, use
the flat wrench provided (g) to loosen the depth stop
bolt (m) and raise bolt to desired height and then
turn jam nut m) clockwise until seated firmly on the
casting. Securely tighten the depth stop bolt before
use.
CAUTION: When changing to a
new wheel, readjust depth stop to
original position to prevent cutting into
supporting surface.
Trigger Switch (fi g. 1)
To start the tool, depress the trigger switch (n). To
turn the tool off, release the trigger switch. Keep
hands and material from wheel until it has coasted
to a stop.
To prevent unauthorized use of tool, install a
standard padlock (not included) into the padlock
hole (o) located in the trigger.
Material Clamping and Supporting
(fi g. 2, 3)
Angles are best clamped and cut with both legs
resting against base.
A spacer block slightly narrower than the
workpiece can be used to increase wheel
utilization (fig. 2).
Long workpieces must be supported by a block
so it will be level with top of base (fig. 3). The
cut off end should be free to fall downward to
avoid wheel binding.
Vise Operation (fi g. 4)
The vise (f) has a quick-travel feature. To release
the vise when it is clamped tightly, turn the crank
(h) counterclockwise one or two times to remove
clamping pressure. Lift vise lever (i) up. Pull crank
assembly out as far as desired. Vise may be pushed
forward into work without cranking. Lower vise lever
(i) then tighten vise (f) on work by using crank (h).
Fence Operation (fi g. 5, 6)
The fence (e) can be adjusted two ways: to change
desired cutting angle and to change spacing
between the fence and vise.
TO CHANGE THE DESIRED CUTTING ANGLE
Use the wrench provided to loosen (do not
remove) the two fence bolts (p). Align the desired
angle indicator line with the slot line (q) in the base
(d). Securely tighten both fence bolts before use.
For more accurate square cuts, disconnect the
power supply, loosen the two fence bolts, push arm
down until wheel extends into base. Place a square
against the wheel and adjust fence against the
square. Securely tighten both fence bolts before use.
When making a miter cut, the vise (f) may not
clamp securely, depending on the thickness of the
workpiece and the miter angle. Other aids (such as
spring, bar or C-clamps) will be necessary to secure
the workpiece to the fence when making these cuts.
TO CHANGE SPACING BETWEEN THE FENCE AND VISE
Using the wrench provided, loosen and remove
the two fence bolts (p). Adjust the fence (e) to
desired locations. Insert both fence bolts in provided
locations. Securely tighten both fence bolts before
use.
Removal and Installation of Wheels
(fi g. 1, 7, 8)
WARNING: Turn off and unplug the
tool before making any adjustments
or removing or installing
attachments or accessories. Be
sure the trigger switch is in the OFF
position. Do not make any adjustment
while the wheel is in motion. Do not
make any adjustment while chop saw is
plugged into power supply.
1. Push in wheel lock lever (l) and rotate wheel
(j) by hand until wheel lock lever engages slot
in inside flange (r) to lock wheel. Loosen the
bolt (s) counterclockwise in the center of the
abrasive wheel with the included flat wrench (g).
Bolt has right-hand thread.
2. Remove the bolt (s), washer (t), outside flange
(u) and old wheel(j).
3. Make sure flange surfaces are clean and flat.
Install the new abrasive wheel by reversing the
above steps.
4. Do not overtighten bolt.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D28720 T 1 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D28720 T 1 in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 1,65 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt D28720 T 1

DeWalt D28720 T 1 Aanvulling / aanpassing - Türkiye - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info