548676
9
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
D28492
D28493
www.
.eu
2
English (original instructions) 4
Français (traduction de la notice d’instructions originale) 15
Copyright DEWALT
1
Figure 1
p
a
b
c
d
e
f
2
Figure 2
Figure 4
Figure 5
A
B
Figure 3
g
d
h
j
k
l l
m
n
o
i
g
e
o
o
h
n
i
o
h
n
i
3
Figure 6
e
q
ENGLISH
4
ANGLE GRINDERS
D28492, D28493
Congratulations!
You have chosen a DEWALT tool. Years of
experience, thorough product development and
innovation make D
EWALT one of the most reliable
partners for professional power tool users.
Technical Data
D28492 D28493
Voltage V 220/240 220/240
Type 3 3
Power input W 2,200 2,200
No-load/rated speed min
-1
6,500 8,500
Wheel diameter mm 230 180
Spindle diameter M14 M14
Weight kg 5.5* 5.5*
* weight includes side handle and guard
Defi nitions: Safety Guidelines
The definitions below describe the level of severity
for each signal word. Please read the manual and
pay attention to these symbols.
DANGER: Indicates an imminently
hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING: Indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION: Indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTICE: Indicates a practice not
related to personal injury which, if
not avoided, may result in property
damage.
Denotes risk of electric shock.
Denotes risk of fire.
WARNING: To reduce the risk of injury,
read the instruction manual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result
in electric shock, fire and/or serious
injury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators. There
is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
ENGLISH
5
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected supply.
Use of an RCD reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of
drugs, alcohol or medication. A moment of
inattention while operating power tools may
result in serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off position before
connecting to power source and/or
battery pack, picking up or carrying the
tool. Carrying power tools with your finger
on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
ADDITIONAL SPECIFIC SAFETY RULES
Safety Instructions for All Operations
a) This power tool is intended to function
as a grinder, sander, wire brush or cut-off
tool. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire
and/or serious injury.
b) Operations such as polishing are not
recommended to be performed with this
power tool. Operations for which the power
tool was not designed may create ahazard and
cause personal injury.
ENGLISH
6
c) Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked
on the power tool. Accessories running faster
than their rated speed can break and fly apart.
e) The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannon be adequately guarded or
controlled.
f) The arbour size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accessories
with arbour holes that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.
g) Do not use a damaged accessory. Before
each use inspect the accessory such as
abrasive wheel for chips and cracks, backing
pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from
the plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.
h) Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection must
be capable of stopping flying debris generated
by various operations. The dust mask or
respirator must be capable of filtrating particles
generated by your operation. Prolonged
exposure to high intensity noise may cause
hearing loss.
i) Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury
beyond immediate area of operation.
j) Hold power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting
accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and
shock the operator.
k) Position the cord clear of the spinning
accessory. If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.
l) Never lay the power tool down until the
accessory has come to a complete stop. The
spinning accessory may grab the surface and
pull the power tool out of your control.
m) Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside
the housing and excessive accumulation of
powdered metal may cause electrical hazards.
o) Do not operate the power tool near
flammable materials. Sparks could ignite these
materials.
p) Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
FURTHER SAFETY INSTRUCTIONS
FOR ALL OPERATIONS
Causes and Operator Prevention
of Kickback
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in turn
causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation at
the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward
or away from the operator, depending on direction
of the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these
conditions.
ENGLISH
7
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given
below:
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control
over kickback or torque reaction during start
up. The operator can control torque reaction or
kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction
opposite to the wheel’s movement at the point
of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp
edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade. Such blades
create frequent kickback and loss of control.
Safety Warnings Specifi c for
Grinding and Abrasive Cutting-Off
Operations
a) Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel. Wheels for
which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The guard must be securely attached to the
power tool and positioned for maximum
safety, so the least amount of wheel is
exposed towards the operator. The guard
helps to protect operator from broken wheel
fragments and accidental contact with wheel
and sparks that could ignite clothing.
c) Wheels must be used only for recommended
applications. For example: do not grind with
the side of cut-off wheel. Abrasive cut-off
wheels are intended for peripheral grinding, side
forces applied to these wheels may cause them
to shatter.
d) Always use undamaged wheel flanges
that are of correct size and shape for your
selected wheel. Proper wheel flanges support
the wheel thus reducing the possibility of wheel
breakage. Flanges for cut-off wheels may be
different from grinding wheel flanges.
e) Do not use worn down wheels from larger
power tools. Wheel intended for larger power
tool is not suitable for the higher speed of a
smaller tool and may burst.
Additional Safety Warnings Specifi c
for Abrasive Cutting-Off Operations
a) Do not “jam” the cut-off wheel or apply
excessive pressure. Do not attempt to make
an excessive depth of cut. Overstressing the
wheel increases the loading and susceptibility to
twisting or binding of the wheel in the cut and
the possibility of kickback or wheel breakage.
b) Do not position your body in line with and
behind the rotating wheel. When the wheel,
at the point of operations, is moving away from
your body, the possible kickback may propel the
spinning wheel and the power tool directly at
you.
c) When wheel is binding or when interrupting
a cut for any reason, switch off the power
tool and hold the power tool motionless
until the wheel comes to a complete stop.
Never attempt to remove the cut-off wheel
from the cut while the wheel is in motion
otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause
of wheel binding.
d) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully reenter the cut. The wheel may
bind, walk up or kickback if the power tool is
restarted in the workpiece.
e) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under
their own weight. Supports must be placed
under the workpiece near the line of cut and
near the edge of the workpiece on both sides of
the wheel.
f) Use extra caution when making a “pocket
cut” into existing walls or other blind areas.
The protruding wheel may cut gas or water
pipes, electrical wiring or objects that can cause
kickback.
ENGLISH
8
Safety Warnings Specifi c for Sanding
Operations
a) Do not use excessively oversized sanding
disc paper. Follow manufacturer's
recommendations, when selecting sanding
paper. Larger sanding paper extending beyond
the sanding pad presents a laceration hazard
and may cause snagging, tearing of the disc
or kickback.
Safety Warnings Specifi c for Wire
Brushing Operations
a) Be aware that wire bristles are thrown by
the brush even during ordinary operation.
Do not overstress the wires by applying
excessive load to the brush. The wire bristles
can easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for
wire brushing, do not allow any interference
of the wire wheel or brush with the guard.
Wire wheel or brush may expand in diameter
due to work and centrifugal forces.
Additional Safety Information
Threaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by flanges, the arbor hole of the
accessory must fit the locating diameter of
the flange. Accessories that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.
The grinding surface of the centre depressed
wheels must be mounted below the plane of
the guard lip. An improperly mounted wheel
that projects through the plane of the guard lip
cannot be adequately protected.
Residual Risks
In spite of the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These are:
Impairment of hearing.
Risk of personal injury due flying particles.
Risk of burns due to accessories becoming hot
during operation.
Risk of personal injury due to prolonged use.
Risk of dust from hazardous substances.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
DATE CODE POSITION (FIG. 1)
The Date Code (p), which also includes the year of
manufacture, is printed into the housing.
Example:
2012 XX XX
Year of Manufacture
Package Contents
The package contains:
1 Angle grinder
1 Guard
1 Side handle
1 Flange set
1 Two-pin spanner
1 Kitbox (K-models only)
1 Instruction manual
1 Exploded drawing
Check for damage to the tool, parts or
accessories which may have occurred during
transport.
Take the time to thoroughly read and
understand this manual prior to operation.
Description (fi g. 1)
WARNING: Never modify the power
tool or any part of it. Damage or
personal injury could result.
a. On/off switch
b. Unlocking switch
c. Spindle lock
d. Guard
e. Side handle
f. Lock-on button
INTENDED USE
The D28492 and D28493 heavy duty angle grinders
have been designed for professional grinding, cutting
and sanding applications.
ENGLISH
9
DO NOT use grinding wheels other than center
depressed wheels and flap-disk.
DO NOT use under wet conditions or in presence of
flammable liquids or gases.
These heavy-duty angle grinders are professional
power tools.
DO NOT let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
This product is not intended for use by persons
(including children) suffering from diminished
physical, sensory or mental abilities; lack of
experience, knowledge or skills unless they are
supervised by a person responsible for their
safety. Children should never be left alone with
this product.
Electrical Safety
The electric motor has been designed for one
voltage only. Always check that the power supply
corresponds to the voltage on the rating plate.
Your DEWALT tool is double insulated in
accordance with EN 60745; therefore no
earth wire is required.
WARNING: 115 V units have to
be operated via a fail-safe isolating
transformer with an earth screen
between the primary and secondary
winding.
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organization.
Mains Plug Replacement
(Middle East and Africa)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved
3–core extension cable suitable for the power input
of this tool (see Technical Data).The minimum
conductor size is 1.5 mm
2
; the maximum length
is 30 m.
When using a cable reel, always unwind the cable
completely.
WARNING: Always ensure that the
cable clamp is correctly and securely
fitted to the sheath of the cable.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off. An accidental start-up can
cause injury.
Attaching Side Handle (fi g. 2)
WARNING: Before using the tool,
check that the handle is tightened
securely.
WARNING: The side handle should
always be used to maintain control of
the tool at all times.
Screw the side handle (e) tightly into one of the holes
(g) on either side of the gear case.
Mounting and Removing the Guard
(fi g. 3)
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off. An accidental start-up can
cause injury.
CAUTION: Guards must be used with
this grinder.
When using the D28942 or D28943 grinder with a
bonded abrasive wheel for cutting metal or masonry
a Type 1 guard MUST be used. Type 1 guards are
available at extra cost from DEWALT distributors.
NOTE: Please refer to the Grinding and Cutting
Accessory Chart at the end of this section to
show other accessories that can be used with these
grinders.
1. Place the angle grinder on a table, spindle (o)
up.
ENGLISH
10
2. Align the lugs (k) with the notches (l).
3. Press the guard (d) down and rotate it to the
required position.
4. Securely tighten the screw (m).
5. To remove the guard, slacken the screw.
CAUTION: If the guard cannot be
tightened by the adjusting screw, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to a service center to repair or replace
the guard.
Fitting and Removing a Grinding or
Cutting Disc (fi g. 1, 4, 5)
WARNING: Do not use a damaged
disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange (i) correctly onto the
spindle (o) (fig. 4).
3. Place the disc (n) on the backing flange (i).
When fitting a disc with a raised center, make
sure that the raised centre (j) is facing the
backing flange (i).
4. Screw the threaded clamp nut (h) onto the
spindle (o) (fig. 5):
a. The ring on the threaded clamp nut (h) must
face towards the disc when fitting a grinding
disc (fig. 5A);
b. The ring on the threaded clamp nut (h) must
face away from the disc when fitting a cutting
disc (fig. 5B).
5. Press the spindle lock button (c) and rotate the
spindle (o) until it locks in position.
6. Tighten the threaded clamp nut (h) with the two-
pin spanner supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the threaded clamp
nut (h) with the two-pin spanner.
Fitting and Removing a
Backing pad/Sanding Sheet
(Fig. 1, 5A)
1. Place the tool on a table or flat surface, with the
guard facing up.
2. Remove the backing flange (i).
3. Place the rubber backing pad correctly onto the
spindle (o).
4. Place the sanding sheet on the rubber backing
pad.
5. Screw the threaded clamp nut (h) onto the
spindle. The ring on the threaded clamp nut
must face towards the rubber backing pad.
6. Press the spindle lock button (c) and rotate the
spindle (o) until it locks in position.
7. Tighten the threaded clamp nut (h) with the two-
pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen
the threaded clamp nut (h) with the two-pin
spanner.
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle
without the use of the spacer and threaded flange.
Prior to Operation
Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
Be sure the inner and outer flange are mounted
correctly.
Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and the
tool.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
WARNING: Always wear regular
working gloves while operating this tool.
WARNING: The gear case becomes
very hot during use.
WARNING:
Ensure all materials to be ground or
cut are secured in place.
Secure and support the workpiece.
Use clamps or a vice to hold and
support the workpiece to a stable
platform. It is important to clamp and
ENGLISH
11
support the workpiece securely to
prevent movement of the workpiece
and loss of control. Movement of
the workpiece or loss of control may
create a hazard and cause personal
injury.
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Install the guard and appropriate disc
or wheel. Do not use excessively worn
discs or wheels.
Be sure the inner and outer flange are
mounted correctly.
Make sure the disc or wheel rotates
in the direction of the arrows on the
accessory and the tool.
Proper Hand Position (fi g. 6)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (e), with the other hand on the main handle
(q) of the tool, as shown.
Switching On and Off (fi g. 1)
The on/off switch is equipped with an unlocking
switch.
To run the tool, depress the unlocking switch (b) and
subsequently operate the on/off switch (a).
Release the unlocking switch (b).
To stop the tool, release the switch.
WARNING: Do not switch the tool on
or off when under load.
Lock-on Button (Fig. 1)
For continuous operation depress the lock-on
button (f) and release the on/off trigger switch.
To stop the tool press the on/off switch again.
The lock-on button can be permanently removed
without compromising compliance with regulatory
agencies shown on the tool’s nameplate. Removal
of the lock pin must be done by a DEWALT Service
Center.
Spindle Lock (fi g. 1)
The spindle lock (c) is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock only when the tool
is turned off, unplugged from the power supply, and
has come to a complete stop.
NOTICE: To reduce the risk of damage
to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly
resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate
the spindle further.
Using Flap Discs
WARNING: Metal dust build-up.
Extensive use of flap discs in metal
applications can result in the increased
potential for electric shock. To reduce
this risk, insert an RCD before use
and clean the ventilation slots daily by
blowing dry compressed air into the
ventilation slots inaccordance with the
below maintenance instructions.
MAINTENANCE
Your DEWALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off. An accidental start-up can
cause injury.
Pop-off Brushes
The motor will be automatically shut off indicating
that the carbon brushes are nearly worn out and
that the tool needs servicing. The carbon brushes
are not user-serviceable. Take the tool to an
authorised DEWALT repair agent.
ENGLISH
12
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of
the main housing with dry air as often as
dirt is seen collecting in and around the
air vents. Wear approved eye protection
and approved dust mask when
performing this procedure.
WARNING: Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING: Since accessories, other
than those offered by DEWALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only DEWALT, recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. This product must
not be disposed of with normal
household waste.
Should you find one day that your D
EWALT product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and
packaging allows materials to be
recycled and used again. Re-use of
recycled materials helps prevent
environmental pollution and reduces
the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at
municipal waste sites or by the retailer when you
purchase a new product.
DEWALT provides a facility for the collection and
recycling of DEWALT products once they have
reached the end of their working life. To take
advantage of this service please return your product
to any authorised repair agent who will collect them
on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
D
EWALT office at the address indicated in this
manual. Alternatively, a list of authorised DEWALT
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
ENGLISH
13
GRINDING AND CUTTING ACCESSORY CHART
Guard Type Accessory Description How to Fit Grinder
TYPE 27
GUARD
Depressed
centre grinding
disc
Type 27 guard
Backing flange
Type 27 depressed
centre wheel
Threaded clamp nut
Flap wheel
Wire wheels
Wire wheels
with threaded
nut
Type 27 guard
Wire wheel
Wire cup with
threaded nut
Type 27 guard
Wire brush
Backing pad/
sanding sheet
Type 27 guard
Rubber backing pad
Sanding disc
Threaded clamp nut
ENGLISH
14
GRINDING AND CUTTING ACCESSORY CHART (cont.)
Guard Type Accessory Description How to Fit Grinder
TYPE 1
GUARD
Masonry
cutting disc,
bonded
Type 1 guard
Backing flange
Cutting wheel
Threaded clamp nut
Metal
cutting disc,
bonded
TYPE 1
GUARD
OR
TYPE 27
GUARD
Diamond
cutting wheels
FRANÇAIS
15
MEULEUSES ANGULAIRES
D28492, D28493
Félicitations!
Vous avez choisi un outil DEWALT. Des années
d’expertise dans le développement et l’innovation
de ses produits ont fait de DEWALT, le partenaire
privilégié des utilisateurs professionnels d’outils
électriques.
Fiche technique
D28492 D28493
Tension V 220/240 220/240
Type 3 3
Puissance absorbée W 2200 2200
Vitesse à vide/nominale min
-1
6500 8500
Diamètre de meule mm 230 180
Diamètre de broche M14 M14
Poids kg 5,5* 5,5*
* le poids inclus la poignée latérale et le carter
Défi nitions: consignes de sécurité
Les définitions ci-après décrivent le degré de risques
associé à chaque balise. Lire soigneusement la
notice d’instructions et respecter ces symboles.
DANGER: indique une situation
de danger imminent qui, si rien
n’est fait pour l’éviter, aura comme
conséquences la mort ou des
dommages corporels graves.
AVERTISSEMENT: indique une
situation de danger potentiel qui, si
rien n’est fait pour l’éviter, pourra avoir
comme conséquences la mort ou des
dommages corporels graves.
ATTENTION: indique une situation
de danger potentiel qui, si rien n’est
fait pour l’éviter, pourrait avoir comme
conséquences des dommages
corporels mineurs ou moindres.
AVIS: indique une pratique ne posant
aucun risque de dommages
corporels, mais qui par contre, si rien
n’est fait pour l’éviter, pourrait poser
des risques de dommages matériels.
Indique des risques de décharges
électriques.
Indique des risques d’incendie.
AVERTISSEMENT: pour réduire tout
risque de dommages corporels, lire la
notice d’instructions
Consignes de sécurité générales
propres aux outils électriques
AVERTISSEMENT! lire toutes les
directives et consignes de sécurité.
Tout manquement aux directives et
consignes ci-incluses comporte des
risques de décharges électriques,
d’incendie et/ou de dommages
corporels graves.
CONSERVER TOUTES CES DIRECTIVES ET
CONSIGNES À TITRE DE RÉFÉRENCE
Le terme «outil électrique» mentionné dans les
avertissements ci-après se rapporte aux outils
alimentés sur secteur (avec fil) ou par piles (sans fil).
1) SÉCURITÉ - AIRE DE TRAVAIL
a) Maintenir l’aire de travail propre et bien
éclairée. Les lieux sombres ou encombrés
sont propices aux accidents.
b) Ne pas utiliser un outil électrique dans un
milieu déflagrant, comme en présence de
liquides, gaz ou poussières inflammables.
Les outils électriques peuvent produire des
étincelles qui pourraient enflammer toute
émanation ou poussière ambiante.
c) Maintenir à l’écart les enfants, ou toute
autre personne, lors de l’utilisation d’un
outil électrique. Toute distraction pourrait
faire perdre la maîtrise de l’appareil.
2) SÉCURITÉ – ÉLECTRICITÉ
a) La fiche électrique de l’outil doit
correspondre à la prise murale. Ne
modifier la fiche en aucune façon. Ne
pas utiliser de fiche d’adaptation avec
un outil électrique mis à la terre (masse).
L’utilisation de fiches d’origine et de prises
appropriées réduira tout risque de décharges
électriques.
b) Éviter tout contact corporel avec des
éléments mis à la terre comme: tuyaux,
radiateurs, cuisinières ou réfrigérateurs.
Les risques de décharges électriques
augmentent lorsque le corps est mis à la
terre.
c) Ne pas exposer les outils électriques à
la pluie ou à l’humidité. Tout contact d’un
FRANÇAIS
16
outil électrique avec un liquide augmente les
risques de décharges électriques.
d) Ne pas utiliser le cordon de façon
abusive. Ne jamais utiliser le cordon
pour transporter, tirer ou débrancher un
outil électrique. Protéger le cordon de
toute source de chaleur, de l’huile, et
de tout bord tranchant ou pièce mobile.
Les cordons endommagés ou emmêlés
augmentent les risques de décharges
électriques.
e) En cas d’utilisation d’un outil électrique à
l’extérieur, utiliser systématiquement une
rallonge conçue à cet effet. Cela diminuera
tout risque de décharges électriques.
f) Si on ne peut éviter d’utiliser un outil
électrique en milieu humide, utiliser
un circuit protégé par un dispositif de
courant résiduel (RCD). Cela réduira tout
risque de décharges électriques.
3) SÉCURITÉ INDIVIDUELLE
a) Rester systématiquement vigilant et faire
preuve de jugement lorsqu’on utilise un
outil électrique. Ne pas utiliser d’outil
électrique en cas de fatigue ou sous
l’influence de drogues, d’alcool ou de
médicaments. Tout moment d’inattention
pendant l’utilisation d’un outil électrique
comporte des risques de dommages
corporels graves.
b) Porter un équipement de protection
individuel. Porter systématiquement un
dispositif de protection oculaire. Le fait
de porter un masque anti-poussières, des
chaussures antidérapantes, un casque
de sécurité ou un dispositif de protection
auditive, lorsque la situation le requiert,
réduira les risques de dommages corporels.
c) Prévenir tout démarrage accidentel.
S’assurer que l’interrupteur est en
position d’arrêt avant de brancher l’outil
sur le secteur et/ou à la batterie, ou de le
ramasser ou le transporter. Transporter un
outil le doigt sur l’interrupteur ou brancher un
outil électrique alors que l’interrupteur est en
position de marche invite les accidents.
d) Retirer toute clé de réglage avant de
démarrer l’outil. Une clé laissée sur une
pièce rotative d’un outil électrique comporte
des risques de dommages corporels.
e) Adopter une position stable. Maintenir les
pieds bien ancrés au sol et conserver son
équilibre en permanence. Cela permettra
de mieux maîtriser l’outil électrique en cas de
situations imprévues.
f) Porter des vêtements appropriés. Ne
porter aucun vêtement ample ou bijou.
Maintenir cheveux, vêtements et gants
à l’écart des pièces mobiles, car ils
pourraient s’y faire prendre.
g) Lorsqu’un dispositif de connexion
à un système de dépoussiérage ou
d’élimination est fourni, s’assurer qu’il est
branché et utilisé correctement. L’utilisation
de ces dispositifs peut réduire les risques
engendrés par les poussières.
4) UTILISATION ET ENTRETIEN DES OUTILS ÉLECTRIQUES
a) Ne pas forcer un outil électrique. Utiliser
l’outil approprié au travail en cours. L’outil
approprié effectuera un meilleur travail, de
façon plus sûre et à la vitesse pour laquelle il
a été conçu.
b) Ne pas utiliser un outil électrique dont
l’interrupteur est défectueux. Tout appareil
dont l’interrupteur est défectueux est
dangereux et doit être réparé.
c) Débrancher la fiche du secteur et/ou
la batterie de l’outil électrique avant
d’effectuer tout réglage, de changer tout
accessoire, ou avant de le ranger. Ces
mesures préventives réduiront tout risque de
démarrage accidentel de l’appareil.
d) Après utilisation, ranger les outils
électriques hors de portée des enfants
et ne permettre à aucune personne non
familière avec son fonctionnement (ou sa
notice d’instructions) de l’utiliser. Les outils
peuvent être dangereux entre des mains
inexpérimentées.
e) Entretenir les outils électriques. Vérifier
les pièces mobiles pour s’assurer qu’elles
sont bien alignées et tournent librement,
qu’elles sont en bon état et ne sont
affectées d’aucune condition susceptible
de nuire au bon fonctionnement de l’outil.
En cas de dommage, faire réparer l’outil
électrique avant toute nouvelle utilisation.
De nombreux accidents sont causés par des
outils mal entretenus.
f) Maintenir tout organe de coupe propre
et bien affûté. Les outils de coupe bien
entretenus et affûtés sont moins susceptibles
de se coincer et sont plus faciles à contrôler.
g) Utiliser un outil électrique, ses
accessoires, mèches, etc., conformément
aux présentes directives et suivant la
manière prévue pour ce type particulier
d’outil électrique, en tenant compte des
conditions de travail et de la tâche à
effectuer. L’utilisation d’un outil électrique
à des fins autres que celles prévues est
potentiellement dangereuse.
FRANÇAIS
17
5) RÉPARATION
a) Faire entretenir les outils électriques par
un réparateur qualifié en n’utilisant que
des pièces de rechange identiques. Cela
permettra de préserver l’intégrité de l’outil
électrique et la sécurité de l’utilisateur.
RÈGLES PARTICULIÈRES DE
SÉCURITÉ ADDITIONNELLES
Consignes générales de sécurité
a) Cet outil électrique a été conçu pour le
meulage, ponçage, brossage métallique
ou le tronçonnage. Lire toute directive
de sécurité, consigne, illustration et
spécification fournie avec l’outil électrique.
Tout manquement aux directives suivantes
pose des risques de décharges électriques,
d’incendie et/ou de blessures graves.
b) Les opérations telles que le polissage ne
sont pas recommandées avec cet outil
électrique. Toute opération pour laquelle l’outil
n’a pas été conçu comporte des risques de
dommages matériels et corporels.
c) Ne pas utiliser des accessoires qui n’ont pas
été spécifiquement conçus et recommandés
par le fabricant de l’outil. Le fait que
l’accessoire peut être rattaché à l’outil électrique
ne veut pas automatiquement dire que son
utilisation ne posera aucun risque.
d) La vitesse nominale des accessoires
doit être équivalente ou supérieure
à celle recommandée sur l’étiquette
d’avertissement de l’outil. Les accessoires
utilisés à une vitesse plus rapide que leur vitesse
nominale peuvent éclater ou se détacher de
l’outil.
e) Le diamètre externe et l’épaisseur de
l’accessoire utilisé doivent se conformer
aux spécifications de la plaque signalétique
de l’outil électrique. Les accessoires aux
spécifications incorrectes ne peuvent être ni
maintenus ni contrôlés de façon adéquate.
f) L’alésage des meules, brides, tampons de
soutien, ou de tout autre accessoire, doit
correspondre parfaitement à la taille de la
broche de l’outil électrique. Les accessoires
dont l’alésage ne correspond pas au dispositif
d’installation de l’outil électrique ne tourneront
pas correctement, vibreront de façon excessive
et pourront causer la perte de contrôle de l’outil.
g) Ne pas utiliser d’accessoires endommagés.
Avant toute utilisation, vérifier tous les
accessoires, par exemple que les meules
abrasives ne sont ni ébréchées ni fendues,
les tampons de soutien ne sont ni fendus ni
usés excessivement, les brosses métalliques
ne comportent aucun élément brisé ou
lâche. En cas de chute, vérifier que l’outil
n’a pas été endommagé et remplacer tout
accessoire abîmé. Après avoir inspecté
et installé un accessoire, se situer, soi-
même et tout individu présent, hors du
plan de rotation de l’accessoire et laisser
tourner l’outil une minute à sa vitesse à
vide maximale. En général, tout accessoire
endommagé se brisera lors du temps d’essai.
h) Porter un équipement de protection
individuel. Selon l’application, utiliser une
protection faciale et des lunettes ou un
masque de protection. Si approprié, porter
un masque anti-poussières, une protection
auditive, des gants et un tablier d’atelier
capables de vous protéger contre toute
projection abrasive ou tout fragment. La
protection oculaire doit être capable d’arrêter
toute projection de débris engendrés par des
opérations diverses. Le masque anti-poussières
doit être capable de filtrer les particules
engendrées par l’opération en cours. Toute
exposition prolongée à un haut niveau de
décibels peut occasionner une perte de l’acuité
auditive.
i) Maintenir à distance toute personne
étrangère au travail en cours. Toute
personne à l’intérieure de l’aire de travail
doit porter un équipement de protection
individuel. Des débris provenant de la pièce
à travailler ou d’un accessoire brisé pourraient
être éjectés et causer des dommages corporels
au-delà de l’aire de travail immédiate.
j) Tenir l’outil par les surfaces isolées prévues
à cet effet pendant toute utilisation où
l’organe de coupe pourrait entrer en contact
avec des fils électriques cachés ou son
propre cordon. Tout contact de l’organe de
coupe avec un fil sous tension met les parties
métalliques exposées de l’outil sous tension et
électrocute l’utilisateur.
k) Maintenir le cordon électrique éloigné de la
partie rotative de l’outil. En cas de perte de
contrôle, le cordon pourrait être sectionné ou
abîmé, et les bras ou mains pourraient entrer en
contact avec l’organe rotatif.
l) Attendre systématiquement l’arrêt complet
de l’outil avant de le déposer. L’organe rotatif
pourrait s’accrocher à la surface utilisée et
rendre l’outil dangereusement imprévisible.
m) Ne pas laisser l’outil électrique en marche
alors qu’il est accroché à votre côté. Tout
FRANÇAIS
18
contact accidentel de l’organe rotatif pourrait
faire que ce dernier s’accroche aux vêtements
et qu’un accessoire entre en contact avec le
corps.
n) Nettoyer régulièrement les orifices
d’aération de l’outil. Le ventilateur du moteur
attirera de la poussière à l’intérieur du boîtier
et une accumulation excessive de poussières
métalliques pourrait poser des risques
d’électrocution/incendie.
o) Ne pas utiliser cet outil électrique à
proximité de matériaux inflammables, car
des étincelles pourraient les enflammer.
p) Ne pas utiliser d’accessoires nécessitant
l’utilisation d’un réfrigérant fluide. L’utilisation
d’eau ou de tout autre réfrigérant fluide pourrait
poser des risques d’électrocution ou de
décharges électriques.
CONSIGNES GÉNÉRALES DE
SÉCURITÉ COMPLÉMENTAIRES
Causes et prévention anti-rebonds
Les rebonds sont la conséquence du grippage
ou coinçage d’une meule, d’un tampon de
soutien, d’une brosse en rotation ou de tout autre
accessoire. Tout grippage ou coinçage causera
rapidement le blocage de l’accessoire en rotation,
ce qui lancera l’outil non contrôlé dans la direction
opposée à l’accessoire en rotation au point du
grippage.
Par exemple, si une meule abrasive reste accrochée
ou pincée dans une pièce à travailler, le bord
de la meule engagée au point de grippage peut
s’enfoncer dans la surface du matériau et faire
tressauter ou rebondir la meule. La meule peut alors
rebondir vers ou à l’opposé de l’utilisateur, selon la
direction du mouvement de la meule au point de
grippage. Dans ces conditions, il peut aussi arriver
que les meules abrasives se brisent.
Les rebonds proviennent d’une utilisation impropre
de l’outil ou de conditions ou procédures
d’exécution incorrectes, et peuvent être évités
en prenant les précautions adéquates énoncées
ci-dessous:
a) Maintenir la scie fermement en positionnant
le corps et les bras de façon à pouvoir
résister à toute force de rebonds. Utiliser
systématiquement la poignée latérale,
si fournie avec l’outil, pour un contrôle
maximal de l’outil en cas de rebonds ou
retour de couple au démarrage. L’utilisateur
peut contrôler le retour de couple ou les forces
de rebonds si des précautions adéquates sont
prises.
b) Ne jamais approcher les mains de l’organe
rotatif. L’accessoire pourrait rebondir sur les
mains.
c) Ne pas positionner le corps dans l’espace
que pourrait occuper l’outil en cas de
rebonds. Les rebonds projetteront l’outil dans
la direction opposée au mouvement de la meule
au point de grippage.
d) Prendre des précautions supplémentaires
pour travailler des coins, des bords acérés,
etc. Éviter que l’accessoire sursaute ou
reste accroché. Les coins, bords acérés ou les
sursauts ont tendance à retenir l’accessoire en
rotation et causer la perte de contrôle de l’outil,
ou des rebonds.
e) Ne pas rattacher une lame à chaîne
coupante, à sculpter ou une lame dentée.
Ces lames posent des risques de rebonds
fréquents et de perte de contrôle de l’outil.
Consignes spécifi ques de sécurité
propres au polissage et au
tronçonnage abrasif
a) Utiliser uniquement des types de meules
recommandés pour votre outil électrique
ainsi que le carter spécifiquement conçu
pour la meule choisie. Les meules non
conçues pour un outil électrique ne peuvent être
adéquatement protégées et sont dangereuses.
b) Le carter doit être soigneusement arrimé à
l’outil électrique et installé pour optimiser
la sécurité, de façon à ce que l’utilisateur
soit le moins possible exposé à la meule.Le
carter aide à protéger l’utilisateur contre toute
projection de fragments et contre tout contact
avec la meule et des étincelles qui pourraient
enflammer les vêtements.
c) Les meules ne doivent être utilisées que
pour les applications recommandées. Par
exemple: ne pas meuler avec la partie
latérale d’une meule à tronçonner. Les
meules à tronçonner ont été conçues pour
le meulage périphérique, toute force latérale
appliquée sur ces meules pourrait les faire
éclater.
d) Utiliser systématiquement des brides de
meules en parfait état, de taille et forme
adaptées à la meule choisie. Les brides
de meules servent de support aux meules,
réduisant ainsi les possibilités que la meule
se brise. Les brides de meules à tronçonner
peuvent différer des brides de disques à meuler.
FRANÇAIS
19
e) Ne pas utiliser de meules émoussées lors
de leur utilisation sur des outils électriques
plus gros. Les meules conçues pour des outils
électriques plus gros ne sont pas adéquates
pour les vitesses plus rapides des outils plus
petits, et risqueraient d’éclater.
Consignes spécifi ques de
sécurité additionnelles propres au
tronçonnage abrasif
a) Ne pas gripper la meule à tronçonner ou lui
appliquer une pression excessive. Ne pas
tenter d’effectuer des profondeurs de coupe
excessives. Pousser excessivement la meule
augmente la charge imposée à l’outil, et les
possibilités de torsion ou grippage de la meule
dans la coupe, et par conséquent les rebonds
et bris.
b) Ne pas aligner le corps avec la meule en
rotation ou se placer derrière elle. Lorsque la
meule, au point d’exécution, s’éloigne du corps,
tout rebond possible pourrait propulser la meule
en rotation et l’outil électrique directement sur
l’utilisateur.
c) En cas de grippage de meule, ou si une
coupe est interrompue pour quelque raison
que ce soit, arrêter l’outil électrique et le
maintenir immobile jusqu’à arrêt complet
de la meule. Ne jamais tenter de retirer une
meule à tronçonner de la coupe alors qu’elle
est en rotation, pour prévenir tout rebond.
Vérifier la pièce à travailler et prendre les
mesures adéquates pour éliminer toute cause
de grippage.
d) Ne pas reprendre l’opération de coupe
dans la pièce. Laisser la meule tourner à
plein régime puis ré-entrer dans la coupe
prudemment. La meule pourrait se gripper,
sortir de la coupe ou effectuer un rebond si
l’outil électrique était remis en marche dans la
pièce à travailler.
e) Soutenir les panneaux, ou toute pièce
surdimensionnée, pour minimiser tout risque
de grippage ou rebond de la meule. Les
pièces larges ont tendance à s’affaisser sous
leur propre poids. Un support doit être installé
sous la pièce à travailler, près de la ligne de
coupe, et près des bords, de chaque côté de la
meule.
f) Prenez des précautions supplémentaires
lors de «coupes de poche» dans des
murs existants ou dans toute zone à
visibilité limitée. La meule pourrait couper
des canalisations de gaz ou d’eau, des fils
électriques ou des objets pouvant causer en
retour des rebonds.
Consignes spécifi ques de sécurité
propres au ponçage
a) Ne pas utiliser des disques de papier
abrasif de taille excessive. Suivre les
recommandations du fabricant lors de la
sélection du papier à poncer. Les feuilles
de papier abrasif de grande taille, dépassant
du tampon ponceur, posent des risques de
lacération, et peuvent faire que le disque
s’accroche ou se déchire, ou causer des
rebonds.
Consignes spécifi ques de sécurité
propres au brossage métallique
a) Prendre des précautions, car des fibres
métalliques sont éjectées par la brosse
pendant le cours normal des opérations.
Ne pas surcharger les fils en appliquant une
pression excessive sur la brosse. Les fibres
métalliques peuvent facilement pénétrer les
vêtements légers et/ou la peau.
b) Si l’utilisation d’un carter est recommandée
pour le brossage métallique, protéger la
brosse métallique circulaire ou la brosse de
toute interférence avec ce carter. Le diamètre
des brosses métalliques circulaires ou des
brosses, peut se dilater. C" est dû au travail et
aux forces centrifuges.
Informations de sécurité
supplémentaires
Le filetage de montage des accessoires
doit correspondre à celui du mandrin de la
meuleuse. Pour les accessoires montés avec
des brides, l’alésage de l’accessoire doit
correspondre au diamètre de positionnement de
la bride. Les accessoires qui ne correspondent
pas au dispositif d’installation de l’outil électrique
ne tourneront pas correctement, vibreront de
façon excessive et pourront causer la perte de
contrôle de l’outil.
La surface de meulage des meules à moyeu
déporté doit être montée au-dessous du
plan de la lèvre du carter de protection. Une
meule mal montée qui dépasse du plan de la
lèvre du carter de protection ne peut pas être
correctement protégée.
FRANÇAIS
20
Risques résiduels
En dépit de l’application des normes de sécurité en
vigueur et de l’installation de dispositifs de sécurité,
certains risques résiduels sont inévitables. Il s’agit
de:
Diminution de l’acuité auditive;
Risques de dommages corporels dus à des
projections de particules;
Risques de brûlures provoquées par des
accessoires ayant surchauffé pendant leur
fonctionnement;
Risques de dommages corporels dus à un
usage prolongé;
Risques posés par les poussières de
substances dangereuses.
Étiquettes sur l’appareil
On trouve les diagrammes suivants sur l’outil:
Lire la notice d’instructions avant toute
utilisation.
Porter un dispositif de protection auditive.
Porter un dispositif de protection oculaire.
EMPLACEMENT DE LA DATE CODÉE DE FABRICATION
(FIG. 1)
La date codée de fabrication (p), qui comprend aussi
l’année de fabrication, est imprimée sur le boîtier.
Exemple:
2012 XX XX
Année de fabrication
Contenu de l’emballage
Ce carton comprend:
1 Meuleuse d’angle
1 Carter de protection
1 Poignée latérale
1 Jeu de flasques
1 Clé à ergots
1 Coffret de transport (modèles K uniquement)
1 Notice d’instructions
1 Dessin éclaté
Vérifier que l’appareil et ses pièces ou
accessoires n’ont pas été endommagés lors du
transport.
Prendre le temps de lire attentivement et
comprendre cette notice d’instructions avant
toute utilisation de l’appareil.
Description (fi g. 1)
AVERTISSEMENT: ne jamais modifier
l’outil ni aucun de ses composants, car
cela pose des risques de dommages
corporels ou matériels.
a. Interrupteur marche/arrêt
b. Bouton de déblocage
c. Blocage de l’arbre
d. Carter de protection
e. Poignée latérale
f. Bouton de verrouillage
USAGE PRÉVU
Les modèles de meuleuses angulaires industrielles
D28492 et D28493 ont été conçues pour les
applications professionnelles de meulage, découpe
et ponçage.
NE PAS utiliser de meules autres que des meules à
moyeu déporté ou des disques à lamelles.
NE PAS utiliser ces outils en milieu ambiant humide
ou en présence de liquides ou de gaz inflammables.
Ces meuleuses angulaires industrielles sont des
outils électriques de professionnels.
NE PAS les laisser à la portée des enfants. Une
supervision est nécessaire auprès de tout utilisateur
non expérimenté.
Ce produit n’est pas prévu pour être utilisé par
des personnes (y compris les enfants) dont les
capacité physiques, sensorielles ou mentales
sont réduites ou qui manquent d’expérience
ou d’aptitudes, sauf si ces personnes sont
surveillées par une autre personne responsable
de leur sécurité. Ne jamais laisser les enfants
seuls avec ce produit.
Sécurité électrique
Le moteur électrique a été conçu pour fonctionner
sur une tension unique. Vérifier systématiquement
que la tension du secteur correspond bien à la
tension indiquée sur la plaque signalétique.
Votre outil DEWALT à double isolation
est conforme à la norme EN60745; un
branchement à la terre n’est donc pas
nécessaire.
FRANÇAIS
21
Si le cordon fourni est endommagé, le remplacer
par un cordon spécialement conçu à cet effet, et
disponible auprès du service après-vente DEWALT.
CH
Toujours utiliser la fiche prescrite lors du
remplacement du câble d’alimentation.
Type 11 pour la classe II
(Isolation double) -outils
Type 12 pour la classe I
(Conducteur de terre) - outils
CH
En cas d’utilisation à l’extérieur, connecter les
outils portatifs à un disjoncteur FI.
Utilisation d’une rallonge
Si une rallonge s’avère nécessaire, utiliser une
rallonge à trois fils homologuée et compatible avec
la tension nominale de cet outil (se reporter à la
section Caractéristiques techniques). La section
minimale du conducteur est de 1,5mm
2
pour une
longueur maximale de 30m.
En cas d’utilisation d’un dévidoir, dérouler
systématiquement le câble sur toute sa longueur.
AVERTISSEMENT: Assurez-vous
toujours que le serre-câble est
solidement et correctement fixé à la
gaine du câble..
ASSEMBLAGE ET RÉGLAGES
AVERTISSEMENT: pour réduire
tout risque de dommages corporels
graves, arrêter et débrancher l’outil
du secteur avant tout réglage ou
avant de retirer ou d’installer toute
pièce ou tout accessoire. Avant de
rebrancher l’outil, presser puis relâcher
la gâchette pour s’assurer que l’outil est
bien à l’arrêt. Tout démarrage accidentel
pourrait causer des dommages
corporels.
Installation de la poignée latérale
(fi g. 2)
AVERTISSEMENT: avant toute
utilisation, vérifier que la poignée est
solidement arrimée.
AVERTISSEMENT: la poignée latérale
doit toujours être utilisée pour conserver
le contrôle de l’outil en permanence.
Vissez fermement la poignée latérale (e) dans
l’un des trous (g) situés de chaque côté du carter
d’engrenage.
Installation et retrait du carter
(fi g. 3)
AVERTISSEMENT: pour réduire
tout risque de dommages corporels
graves, arrêter et débrancher l’outil
du secteur avant tout réglage ou
avant de retirer ou d’installer toute
pièce ou tout accessoire. Avant de
rebrancher l’outil, presser puis relâcher
la gâchette pour s’assurer que l’outil est
bien à l’arrêt. Tout démarrage accidentel
pourrait causer des dommages
corporels.
ATTENTION: cette meuleuse à disque
doit être utilisée avec un carter.
Pour utiliser les modèles de meuleuses à disque
D28942 et D28943 avec une meule abrasive
agglomérée pour la découpe du métal ou de la
maçonnerie, un carter de type 1 DOIT être utilisé.
Les carters de type 1 sont vendus séparément chez
votre distributeur DEWALT.
REMARQUE: veuillez vous reporter au Tableau
d’accessoires de meulage et de tronçonnage en
fin de section pour obtenir la liste des accessoires
pouvant être utilisés avec ces meuleuses.
1. Disposer la meuleuse angulaire sur une table,
avec la broche (o) sur le dessus.
2. Alignez les pattes (k) sur les encoches (l).
3. Poussez sur le carter (d) et tournez-le dans la
position requise.
4. Vissez soigneusement la vis (m).
5. Pour retirer le carter, dévissez la vis.
ATTENTION: si le carter ne peut pas
être resserré correctement à l’aide de
la vis, ne pas utiliser l’outil. Pour réduire
tout risque de dommages corporels,
amener l’outil et le carter dans un centre
de réparation pour faire réparer ou
remplacer le carter.
Installation et retrait d’un disque à
meuler ou à tronçonner (fi g. 1, 4, 5)
AVERTISSEMENT: ne pas utiliser de
disque endommagé.
1. Disposez l’outil sur une table, avec le carter sur
le dessus.
2. Installez correctement la bride de soutien (i) sur
la broche (o), (fig. 4).
FRANÇAIS
22
3. Placez le disque (n) sur la bride de soutien (i).
Lors de l’installation d’un disque avec un centre
en relief, assurez-vous que ce centre en relief (j)
soit positionné contre la bride de soutien (i).
4. Vissez l’écrou de blocage fileté (h) sur la broche
(o) (fig. 5).
a. L’anneau sur l’écrou de blocage fileté (h) doit
se trouver contre le disque lorsqu’on utilise
un disque de meulage (fig. 5A).
b. L’anneau sur l’écrou de blocage fileté (h) doit
se trouver à l’opposé du disque lorsqu’on
utilise un disque à tronçonner (fig. 5B).
5. Appuyez sur le bouton de blocage de l’arbre
(c) puis faites pivoter la broche (o) jusqu’à ce
qu’elle se verrouille en place.
6. Resserrez l’écrou de blocage fileté (h) à l’aide de
la clé de serrage à deux broches fournie avec
l’outil.
7. Libérez le bouton de blocage de l’arbre.
8. Pour retirer le disque, desserrez l’écrou de
blocage fileté (h) à l’aide de la clé de serrage à
deux broches.
Montage et démontage du tampon
support/papier abrasif (fi g. 1, 5A)
1. Placez l’outil sur une table ou une surface
plane, avec le carter de protection tourné vers
le haut.
2. Retirez la bride de support (i).
3. Placez le tampon support en caoutchouc
correctement sur la
broche (o).
4. Placez le papier abrasif sur le tampon support
en caoutchouc.
5. Vissez l’écrou de blocage fileté (h) sur la
broche. L’anneau sur l’écrou de blocage fileté
doit être tourné vers le tampon support.
6. Appuyez sur le bouton de blocage de l’arbre
(c) puis faites pivoter la broche (o) jusqu’à ce
qu’elle se verrouille en place.
7. Resserrez l’écrou de blocage fileté (h) à l’aide
de la clé de serrage à deux broches.
8. Libérez le verrouillage de l’arbre.
9. Pour retirer le tampon support en caoutchouc,
desserrez l’écrou de blocage fileté (h) à l’aide
de la clé de serrage à deux broches.
Montage d’une brosse métallique
Vissez la brosse métallique directement sur l’arbre,
sans utiliser l’entretoise ni le flasque fileté.
Avant tout utilisation
Installez le carter et le disque ou la meule
appropriés. N’utilisez aucun disque ou meule
excessivement émoussé.
Assurez-vous que les brides, externe et interne,
sont correctement installées.
Assurez-vous que le disque ou la meule
tourne dans le sens des flèches marquées sur
l’accessoire et l’outil.
FONCTIONNEMENT
Consignes d’utilisation
AVERTISSEMENT: respecter
systématiquement les consignes de
sécurité et les normes en vigueur.
AVERTISSEMENT: pour réduire
tout risque de dommages corporels
graves, arrêter et débrancher l’outil
du secteur avant tout réglage ou
avant de retirer ou d’installer toute
pièce ou tout accessoire. Avant de
rebrancher l’outil, presser puis relâcher
la gâchette pour s’assurer que l’outil est
bien à l’arrêt.
AVERTISSEMENT: Portez toujours
des gants de travail appropriés lors de
l’utilisation de cet outil.
AVERTISSEMENT: Le boîtier
d’engrenage devient très chaud
pendant l’utilisation.
AVERTISSEMENT:
S’assurer que le matériau à meuler ou
à tronçonner est fermement arrimé.
Fixer et soutenir l’ouvrage. Utilisez
les pinces ou un étau pour fixer et
soutenir l’ouvrage sur une plateforme
stable. Il est important pour serrer
et soutenir l’ouvrage de manière
sûre afin d’éviter le mouvement de
l’ouvrage et la perte de contrôle. Le
mouvement de l’ouvrage ou la perte
de contrôle peuvent représenter
un risque et causer des blessures
personnelles.
Appliquer seulement une pression
légère sur l’outil. Ne pas exercer de
pression latérale sur le disque.
Éviter toute surcharge. Si l’outil venait
à surchauffer, le laisser fonctionner à
vide quelques minutes.
FRANÇAIS
23
• Installez le carter de protection et
le disque ou la meule adaptés. Ne
pas utiliser de meules ou de disques
trop usés.
• Vérifiez le montage des flasques
intérieur et extérieur.
• Vérifiez que la meule ou le disque
tourne dans le sens des flèches sur
l’accessoire et l’outil.
Position correcte des mains
(fi g. 6)
AVERTISSEMENT: pour réduire tout
risque de dommages corporels graves,
adopter SYSTÉMATIQUEMENT la
position des mains illustrée.
AVERTISSEMENT: pour réduire
tout risque de dommages corporels
graves, maintenir fermement et
SYSTÉMATIQUEMENT l’outil pour
anticiper toute réaction soudaine de sa
part.
La position correcte des mains nécessite une main
sur la poignée latérale (e) et l’autre main sur la
poignée principale (q) de l’outil, comme illustré.
Mise en marche et arrêt (fi g. 1)
L’interrupteur marche/arrêt est équipé d’un bouton
de déblocage.
Pour utiliser l’outil, appuyez sur le bouton de
déblocage (b), puis sur l’interrupteur marche/arrêt (a).
Relâchez le bouton de déblocage (b).
Pour arrêter l’outil, relâcher l’interrupteur.
AVERTISSEMENT: Ne mettez pas en
marche et n’arrêtez pas l’outil lorsqu’il
est en charge
Bouton de verrouillage (fi g. 1)
Pour un fonctionnement continu, appuyez sur le
bouton de verrouillage (f) et relâchez l’interrupteur
marche/arrêt.
Pour arrêter l’outil, appuyez à nouveau sur
l’interrupteur marche/arrêt.
Le bouton de verrouillage peut être retiré de manière
permanente sans compromettre la conformité aux
organismes réglementaires indiqués sur la plaque
signalétique de l’outil. Le retrait de la goupille de
verrouillage doit être effectué par un centre de
service DEWALT.
Bouton de blocage de l’arbre (fi g. 1)
Le bouton de blocage de l’arbre (c) est destiné à
empêcher la broche de tourner lors de l’installation
ou du retrait de la meule. N’utilisez le bouton de
blocage de l’arbre que lorsque l’outil est à l’arrêt,
débranché du secteur, et après arrêt complet du
moteur.
AVIS: pour réduire tout risque de
dommages matériels, ne pas actionner
le bouton de blocage de l’arbre alors
que l’outil est en marche. L’outil pourrait
non seulement être endommagé
mais tout accessoire installé pourrait
se détacher et poser des risques de
dommages corporels.
Pour actionner le verrouillage, appuyez sur le bouton
de blocage de l’arbre puis faites tourner la broche
jusqu’à la bloquer complètement.
Utilisation de disques à lamelles
AVERTISSEMENT: accumulation de
poussières métalliques. L’utilisation
intensive de disques à lamelles pour
des applications métal pose des risques
accrus de décharges électriques.
Pour réduire ces risques, insérer un
DCR avant utilisation et nettoyer les
fentes d’aération quotidiennement
en y soufflant de l’air comprimé
conformément aux instructions de
maintenance ci-dessous.
MAINTENANCE
Cet outil DEWALT a été conçu pour fonctionner
longtemps avec un minimum de maintenance. Le
fonctionnement continu et satisfaisant de l’outil
dépend d’un entretien adéquat et d’un nettoyage
régulier.
AVERTISSEMENT: pour réduire
tout risque de dommages corporels
graves, arrêter et débrancher l’outil
du secteur avant tout réglage ou
avant de retirer ou d’installer toute
pièce ou tout accessoire. Avant
de rebrancher l’outil, presser puis
relâcher la gâchette pour s’assurer
que l’outil est bien à l’arrêt. Tout
démarrage accidentel pourrait causer
des dommages corporels.
FRANÇAIS
24
Balais autorupteurs
Le moteur sera coupé automatiquement pour
indiquer que les balais de charbon sont presque
usés et qu’il faut effectuer la maintenance de l’outil.
Les balais de charbon ne peuvent être remplacés
par l’utilisateur. Rapportez l’outil chez un réparateur
agréé D
EWALT.
Lubrifi cation
Votre outil électrique ne requiert aucune lubrification
additionnelle.
Entretien
AVERTISSEMENT: éliminer poussière
et saleté du boîtier principal à l’aide d’air
comprimé chaque fois que les orifices
d’aération semblent s’encrasser. Porter
systématiquement des lunettes de
protection et un masque anti-poussières
homologués au cours de cette
procédure.
AVERTISSEMENT: ne jamais utiliser
de solvants ou tout autre produit
chimique décapant pour nettoyer
les parties non métalliques de l’outil.
Ces produits chimiques pourraient en
attaquer les matériaux utilisés. Utiliser
un chiffon humidifié avec de l’eau et
un savon doux. Protéger l’outil de tout
liquide et n’immerger aucune de ses
pièces dans aucun liquide.
Accessoires en option
AVERTISSEMENT: comme les
accessoires autres que ceux offerts par
DEWALT n’ont pas été testés avec ce
produit, leur utilisation avec cet appareil
pourrait être dangereuse. Pour réduire
tout risque de dommages corporels,
seuls des accessoires DEWALT
recommandés doivent être utilisés avec
cet appareil.
Veuillez consulter votre revendeur pour plus
d’informations sur les accessoires appropriés.
Protection de l’environnement
Collecte sélective. Ne pas jeter ce produit
avec les ordures ménagères.
En fin de durée de vie ou d’utilité de votre
produit D
EWALT, ne pas le jeter avec les ordures
ménagères, mais dans les conteneurs de collecte
sélective.
La collecte sélective des produits et
emballages usagés permet de recycler et
réutiliser leurs matériaux. La réutilisation
de matériaux recyclés aide à protéger
l’environnement contre la pollution et à
réduire la demande en matière première.
Selon les réglementations locales, il peut être offert:
service de collecte sélective individuel des produits
électriques, ou déchetterie municipale ou collecte
sur les lieux d’achat des produits neufs.
DEWALT dispose d’installations pour la collecte et
le recyclage des produits DEWALT en fin de vie.
Pour profiter de ce service, veuillez rapporter votre
produit auprès d’un centre de réparation agréé qui le
recyclera en notre nom.
Pour connaître l’adresse d’un centre de réparation
agréé près de chez vous, veuillez contacter votre
distributeur DEWALT local à l’adresse indiquée dans
cette notice d’instructions, ou consulter la liste des
centres de réparation agréés DEWALT, l’éventail de
notre SAV et tout renseignement complémentaire
sur Internet à l’adresse: www.2helpU.com.
FRANÇAIS
25
TABLEAU D'ACCESSOIRES DE MEULAGE
Type de carter Accessoire Description Installation de la meule
CARTER DE
TYPE 27
Meule à moyeu
déporté
Carter de type 27
Bride de soutien
Meule de type 27 à moyeu
déporté
Écrou de blocage fileté
Disque à
lamelles
Brosse
métallique
circulaire
Brosse
métallique à
écrou taraudé
Carter de type 27
Brosse métallique circulaire
Brosse
coupelle à
écrou taraudé
Carter de type 27
Brosse métallique
Tampon de
soutien/disque
abrasif
Carter de type 27
Tampon de soutien en
caoutchouc
Disque abrasif
Écrou de blocage fileté
FRANÇAIS
26
TABLEAU D'ACCESSOIRES DE MEULAGE (suite)
Type de carter Accessoire Description Installation de la meule
CARTER DE
TYPE 1
Disque de
coupe de
maçonnerie,
liaisonné
Carter de type 1
Bride de soutien
Meule à tronçonner
Écrou de blocage fileté
Disque à métal,
liaisonné
CARTER DE
TYPE 1
OU
CARTER DE
TYPE 27
Meule à
tronçonner
diamantée
27
28
Afghanistan Ariana Hafiz Zabi Co. Ltd. info@arianahafiz.com Tel: 93-0-799331079
Dahan Bagh Squire Karte Ariana, Kabul, Afghanistan Fax: 93-0-700007576 / 93-0-799331079
Algeria Sarl Outillage Corporation hakim.merdjadi@outillage-dz.com Tel: 213-0-21375130
08, Rue Med Boudiaf (ex TELLA Achen) lyes@outillage-dz.com 213-0-21375131
Cheraga, Alger Mali.faiza@outillage-dz.com; Fax: 213-0-21369667
sidahmed@outillage-dz.com
Angola Angoferraria, Lda. angoferraria@gmail.com Tel: 244-222-395837 / 244-222-395034
Rua Robert Shields, nº 61, Luanda, Angola sequeira.angoferraria@gmail.com Fax: 244-222-394790
Azerbaijan Royalton Holdings Ltd. jai@royaltonholdings.com Tel: 994-12-4935544
41 Khagani St. Apt. 47 AZ1001 Baku- Azerbaijan office@royaltonholdings.com Fax: 994-12-5980378
Egypt ElFarab S.A.E. elfarab@elfarab.com Tel: 202-37603946
15-Nabil El Wakkad Street, Dokki, adel.ezzat@elfarab.com Fax: 202-33352796
Giza, Egypt mahmoud.elhosseiny@elfarab.com
Ethiopia Seif Tewfik Sherif seif@ethionet.et Tel: 251-11-1563968
Arada Sub City, Kebele 01/02, Global Insurance Bldg., nawanag@ethionet.et 251-11-1563969
2nd Flr., Room 43, P.O. Box 2525, Addis Ababa Fax: 251-11-1558009
Iraq Al-Sard Co. for General Trading Ltd dewalt.service@yahoo.com Tel: 964-18184102
Jbara Bldg. 3Flr. Al Rasheed St., Baghdad, Iraq
Jordan Amman West Stores-Bashiti ali@bashitistores.com Tel: 962-6-5350009
210 Garden St. Tla’a Ali, P.O. Box 1564 yousef@bashitistores.com Fax: 962-6-5350012
Tla Ali Amman 11953, Jordan
Kenya Dextron Tools Ltd. info@alibhaishariff.co.ke Tel: 254-20-6905000
P.O. Box 20121-00200, Shariff House, dextron@alibhaishariff.co.ke 254-20-2358021
Kimathi Street, Nairobi Fax: 254-20-6905111 / 254-20-6905112
Lebanon Est. Shaya & Azar S.A.R.L. shayazar@dm.net.lb Tel: 961 1 872305
Boulvard Jdeideh - Mar Takla - Bouchrieh . 961 1 872306
P.O. Box 90545, Jdeideh. Beirut – Lebanon Fax: 961 1 872303
Libya North Africa Trading ( El Ghoul Brothers) maryam_farooq2003@yahoo.com Tel: 218-061-3383994
P.O. Box 348, 7 October Street 11 nagte@eim.ae Fax: 218-092-7640688
Benghazi dewalt_libya@yahoo.com
North Africa Trading ( El Ghoul Brothers) dewalt_libya@yahoo.com Tel: 218-021-3606430
AlBarniq D
EWALT Center, Fax: 218-092-6514813
Mokhazin-elsukar St. ElFallah, Tripoli
North Africa Trading ( El Ghoul Brothers) Tel: 218-091-3221408
AlHilal Service Center Tawergha St., Misurata
Mauritius Robert Le Marie Limited a.blackburn.rlm@rlmgroup.mu Tel: 230-212 1865
Old Moka Road, Bell Village, P.O. Box 161, jm.pierrelouis.rlm@rlmgroup.mu 230-212 2847
Port Louis Fax: 230-2080843
Morocco Ets Louis Guillaud & Cie boumadiane.azedine@elg.ma Tel: 522-301446 / 305971 / 317815 /
31, Rue Pierre Parent, doukkali.marouane@elg.ma 315576
Casablanca – 21000 Fax: 522-444518 / 317888
Nigeria Meridian Power Tools Ltd. braj@meridian-nigeria.com Tel: 234-1-7740431
Gr. Floor, #1 Alhaji Masha Rd, Next toTeslim Balogun 234-1-7740410
Stadium, Near National Stadium Surulere, Lagos, Nigeria Fax: 234-1-7913798
Pakistan Northern Toolings (Pvt) Ltd.-Lahore zhayee@northern.pk Tel: 92-423-7651220
86- Railway Road, Lahore – 7 import@northern.pk 92-423-7641675
Pakistan sales@northern.pk Fax: 92-423-7641674
Northern Toolings (Pvt) Ltd.-Karachi karachibr@northern.pk Tel: 92-213-2465305
224-231 Industrial Town Plaza, Shahrah-e-Liaqat, 92-213-2465307
Karachi, Pakistan Fax: 92-213-2465301
Northern Toolings (Pvt) Ltd.-Taxila taxilabr@northern.pk Tel: 92-51-4545811
Al-Rehman Plaza, Opposite Tehsil Court, Fax: 92-51-4544194
Faisal Shaheed Road, Taxila
South Benray Tool Wholesalers C.C. dewaltservice@benray.co.za Tel: 27-11-6838350
Africa 91 Turffontein Road, Stafford, Johannesburg, 2001 P.O. zain@benray.co.za Fax: 27-11-6837456
Box 260037 EXCOM 2023, South Africa shafiq@benray.co.za
Tanzania General Motors Investment Ltd. ezra@gmi-tz.com Tel: 255-22-2865022 /
14 Vingunguti-Nyerere Road, P.O.Box 16541, info@gmi-tz.com 2862661 / 2862671 / 2862659
Dar es Salaam, Tanzania chiwelesa@yahoo.com Fax: 255-22-2862667
Tunisia Ets. Mohamed Ghorbel slim.ghorbel@gnet.tn Tel: 216-71794248
03 Rue 8603 Charguia I Tunis. moh.ghorbel@gnet.tn 216-71793848
Postal Code 2035 mourad.ghorbel@gnet.tn Fax: 216-71770759
Uganda The Building Center (u) Ltd. tbc@africaonline.co.ug Tel: 256-041-4234567
52 Station Road, Kitgum House, chris@tbcu.co.ug 256-041-4259754
P.O. Box 7436 Kampala, Uganda Fax: 256-041-4236413
Yemen Middle East Trading Co. (METCO) tamer.metco@gmail.com Tel: 967-4-213455
5th Flr.Hayel Saeed Anam Bldg. tamer@metcotrading.com Fax: 967-4-219869
Al-Mugamma St. Taiz, metco@metcotrading.com
Yemen sami@metcotrading.com
Middle East Trading Co. (METCO) tamer.metco@gmail.com Tel: 967-2-222670
Mualla Dakka, tamer@metcotrading.com Fax: 967-2-222670
Aden metco@metcotrading.com
Middle East Trading Co. (METCO) tamer.metco@gmail.com Tel: 967-1-204201
Hayel st., Sana'a, tamer@metcotrading.com Fax: 967-1-204204
Yemen metco@metcotrading.com
UAE Black & Decker (Overseas) GmbH service.mea@blackdecker.com Tel: 971-4 8127400 / 8127406
P.O. Box 5420, Dubai Fax: 971-4 2822765
Ideal Star Workshop Eqpt. Trading LLC idealeq@emirates.net.ae Tel: 971-4 3474160
P.O. Box 37116, Al Quoz, Dubai Fax: 971-4 3474157
Alebrah Engineering Service alebrah@eim.ae Tel: 971-4 2850044
P.O. Box 78954, Al Qusais, Dubai Fax: 971-4 2844802
Burj Al Madeena dewaltuae@hotmail.com Tel: 971-6 5337747
Industrial Area No. 1, opp. Pakistani Masjid Fax: 971-6 5337719
P.O. Box 37635, Sharjah
McCoy Middle East LLC mccoy@emirates.net.ae Tel: 971-6 5395931
P.O. Box 25793, Sharjah Fax: 971-6 5395932
McCoy Middle East LLC mccoyrak@gmail.com Tel: 971-7 2277095
P.O. Box 10584, Ras Al Khaimah Fax: 971-7 2277096
Al Sukoon Gen. Trdg. Co. LLC sukoon@eim.ae Tel: 971-6 7435725 / 7438317
P.O. Box 2975, Ajman Fax: 971-6 7437350
Zillion Equipment and Spare Parts Trading LLC zilliontrdg@gmail.com Tel: 971-3 7216690
P.O. Box 19740, opp. Bin Sadal / Trimix Redymix Sanaiya, Al Ain Fax: 971-3 7216103
Light House Electrical, Abu Dhabi Branch dewalt_lhe@hotmail.com Tel: 971-2 6726131
P.O. Box 120, Abu Dhabi Fax: 971-2 6720667
Light House Electrical, Musaffah Branch dewalt_lhe@hotmail.com Tel: 971-2 5548315
P.O. Box 120, Abu Dhabi Fax: 971-2 5540461
Bahrain Alfouz Services Co. WLL alfouz@batelco.com.bh Tel: 973 17783562 / 17879987
P.O. Box 26562, Tubli, Manama Fax: 973 17783479
Kavalani & Sons W.L.L. info@kavalani.com Tel: 973 17732888
P.O. Box 71, Sitra, Manama pradeep@kavalani.com Fax: 973 17737379
Kuwait Al Omar Technical Co. alexotc@usa.net Tel: 965 24848595 / 24840039
P.O. Box 4062, Safat 13041, Kuwait Fax: 965 24845652
Fawaz Al Zayani Establishment dewaltkuwait@hotmail.com Tel: 965 24828710
P.O. Box 42426, Shop No.18, Fax: 965 24828716
Al Humaizi Commercial Complex, Khalifa Al Jassim, Shuwaikh
Fawaz Al Zayani Establishment dewaltkuwait@hotmail.com Tel: 965 23925830
Fahaheel Industrial Area, Main St., Sanaya Fax: 965 24828716
Oman Al Jizzi Company LLC aljizied@omantel.net.om Tel: 968 24832618 / 24835153
P.O. Box 1704, P.C. 112, Ruwi jizzi10@omantel.net.om Fax: 968 24831334 / 24836460
Al Hassan Technical & Construction Supplies Co. LLC hamriya.sr@al-hassan.com Tel: 968 24810575 / 24837054
P.O. Box 1948, P.C. 112, Ruwi abrar.h@al-hassan.com Fax: 968 24810287 / 24833080
Oman Hardware Co. LLC omanhard@omantel.net.om Tel: 968 24815131
P.O. Box 635, Ruwi Postal Code 112 Fax: 968 24816491
Khimji Ramdas bilal.m@khimjiramdas.com Tel: 968 24595906/ 907
P.O. Box 19, Post Code 100, Ghala, Muscat Fax: 968 24852752
Qatar Teyseer Industrial Supplies & Services Co. WLL manish@tissco-qatar.com Tel: 974 4581536
55, Al Wakalat St. (Between St. 18 & 19) tool.service@tissco-qatar.com Fax: 974 4682024
Salwa Industrial Area, P.O. Box 40523 Doha
Shaheen Electrical Works & Trading Co. WLL shaheenelc@gmail.com Tel: 974 460 02 30 / 460 05 25
Gate 34, St. 44 Industrial Area P.O. Box 9756, Doha Fax: 974 460 13 38
KSA Industrial Material Organization (IMO) service@imo.com.sa Tel: 966-1 4028010 Ext. 26
P.O. Box 623, Rail Street, Riyadh Tel: 966-1 8001245757
Fax: 966-1 4037970
Fawaz Ebrahim Al Zayani Trading Est. dewaltdammam@hotmail.com Tel: 966-3 8140914
P.O. Box 76026, Al Raka : 31952 Fax: 966-3 8140824
MSS (Al-Mojil Supply & Services) mssjubail@almojilservices.com Tel: 966-3 3612850 / 3624487
P.O. Box 450, Jubail 31951 alex.chang@almojilservices.com Tel: 966-3 3621729
Opp-Gulf Bridge Library & Riyadh House Fax: 966-3 3623589 / 3620783
EAC (Al Yousef Contg. & Trdg. Est.) golamkibria77@yahoo.com Tel: 966-2 6519912
P.O. Box 30377, Jeddah -21477 Fax: 966-2 6511153
Mohamed Ahmed Bin Afif Est. binafifyanbu@hotmail.com Tel: 966-4 3222626 / 3228867
P.O. Box 530, Yanbu, Al Bahr Fax: 966-4 3222210
Garziz Trading for Bldg Mat & Decoration agarziz@yahoo.com Tel: 966-4 826 14 90 / 822 76 36
P.O. Box 3364, Madina Fax: 966-4 826 57 41
Sultan Garment Factory (RSC) rscservice@digi.net.sa Tel: 966-1 4055148 / 4042889
P.O. Box 29912, Riyadh 11467 Fax: 966-1 4055148
Al Bawardi Tools & Hardware asattar@albawardi.com Tel: 966-3 8330780 Ext. 24
P.O. Box 112, Dammam 31411 nibanez@albawardi.com Tel: 966-3 8348585 Ext. 24
Fax: 966-3 8336303
Al Bawardi Tools & Hardware rbaltao@albawardi.com Tel: 966-1 4484999
P.O. Box 68, Riyadh 11411 asamad@albawardi.com Fax: 966-3 4487877
Al Bawardi Tools & Hardware sharadji@albawardi.com Tel: 966-2 6444547 / 6439035
P.O. Box 16905, Jeddah 21474 fgaber@albawardi.com Tel: 966-2 6456095
Fax: 966-2 6439024
N205634 08/12
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D28492 T 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D28492 T 5 in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 4,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van DeWalt D28492 T 5

DeWalt D28492 T 5 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanõl, Polski, Türkiye, Dansk, Svenska, Norsk, Suomi - 200 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info