546219
45
Verklein
Vergroot
Pagina terug
1/172
Pagina verder
43
ENGLISH
Loosen the lock knob (59) of the fi rst leg (15).
Fold the leg inwards.
Tighten the lock knob.
Repeat as for the other legs.
Turn the machine straight up.
Mounting the wheels (fi g. D)
Place a wheel (14) onto the axles (60) on each side of the machine.
Place a fl at washer (61) and a nut (62) onto the threaded end of the axles.
Tighten the nuts using the spanner supplied.
Assembly for mitre saw mode
Mounting the under-table guard (fi g. E)
The under-table guard (63) is fi tted to the top of the saw bench table.
Place the two fasteners on the left of the guard into the slots (64) on
the left of the blade slot (65). Turn the plastic screws counterclockwise.
Place the guard fl at on the table and press the fastener in the slot (66)
on the right of the blade slot. Turn the plastic screw counterclockwise.
To remove, turn the screws clockwise and remove the guard.
Turning the sawhead and table over (fi g. F1 - F4)
Hold the saw table (19) with one hand and push the table release lever
(2) to the right (fi g. F1).
Push the table downwards at the front (fi g. F2) and swing it over
completely until the motor assembly is uppermost and the plate (67)
engages in the table locking device (68) (fi g. F3).
Push the release lever (69) to the rear whilst holding down the head
until the spring-loaded bearing unit (70) can be lifted out of its seating
(fi g. F4).
Flip the bearing unit up.
Holding the head fi rmly, allow the spring pressure to take the head
upwards into its rest position.
Mounting the saw blade (fi g. G1 - G4)
WARNING: To reduce the risk of injury, turn unit off and
disconnect machine from power source before installing
and removing accessories, before adjusting or changing
set-ups or when making repairs. Be sure the trigger switch
is in the OFF position. An accidental start-up can cause injury.
WARNING:
• Always change blades with the machine in mitre saw mode.
Never depress the spindle lock button while the blade is under
power or coasting.
Do not cut ferrous metal (containing iron or steel) or masonry or
fibre cement product with this mitre saw.
The teeth of a new blade are very sharp and can be dangerous.
Depress the head lock up release lever (9) to release the
lower guard (8), then raise the lower guard as far as possible
(Fig.G1).
With the lower guard held in the raised position, depress the spindle
lock button (74) with one hand, then use the supplied blade spanner
in the other hand to loosen the left-hand threaded blade locking screw
(73) by turning clockwise.
WARNING! To use the spindle lock, press the button as shown
and rotate the spindle by hand until you feel the lock engage.
Continue to hold the lock button in to keep the spindle from turning
(74, fig.G1).
Remove the blade locking screw (73) and the outside arbor collar (75).
• Install the saw blade (76) onto the shoulder (77) provided on the
inside arbor collar (78), making sure that the teeth at the bottom edge
of the blade are pointing toward the back of the saw (away from the
operator).
Replace the outer arbor collar (75).
Tighten the blade locking screw (73) carefully by turning counter-
clockwise while holding the spindle lock engaged with your other hand.
Raise the lower guard.
WARNING! Be aware the saw blade shall be replaced in the
described way only. Only use saw blades as specified under
Technical Data; Cat.no.: DT4260 is suggested.
Adjustments for mitre saw mode
Your mitre saw was accurately adjusted at the factory. If readjustment due
to shipping and handling or any other reason is required, follow the steps
below to adjust your saw. Once made, these adjustments should remain
accurate.
Checking and adjusting the blade to the fence (fi g. H1 - H3)
Loosen the mitre knob (79) and depress the mitre latch (80) to release
the rotating table (5) (fi g. H1).
Swing the rotating table until the latch locates it at the 0° mitre position.
Do not tighten the knob.
Pull down the head until the blade just enters the saw kerf (81).
Place a square (82) against the left side (7) of the fence and blade (76)
(fi g. H2).
WARNING: Do not touch the tips of the blade teeth with the
square.
If adjustment is required, proceed as follows:
Loosen the screws (83) (fi g. H3) and move the scale/rotating table
assembly left or right until the blade is at 90° to the fence as measured
with the square (fi g. H2).
Retighten the screws (83) (fi g. H3). Pay no attention to the reading of
the mitre pointer at this point.
Adjusting the mitre pointer (fi g. H1 & H4)
Loosen the mitre knob (79) and depress the mitre latch (80) to release
the rotating table (5) (fi g. H1).
With the mitre knob loose, allow the mitre latch to snap into place as
you rotate the mitre arm past zero.
Observe the pointer (84) and mitre scale (85) (fi g. H4). If the pointer
does not indicate exactly zero, loosen the screw (86), move the pointer
to read 0° and tighten the screw.
Checking and adjusting the blade to the table (fi g. I1 - I3)
Loosen the bevel clamp knob (17) (fi g. I1).
Press the saw head to the right to ensure it is fully vertical and tighten
the bevel clamp knob.
Pull down the head until the blade just enters the saw kerf (81).
Place a set square (82) on the table and up against the blade (76) (fi g. I2).
WARNING: Do not touch the tips of the blade teeth with the
square.
If adjustment is required, proceed as follows:
Loosen the bevel clamp knob (17) (fi g. I1) and turn the vertical position
adjustment stop screw (87) (fi g. I3) in or out until the blade is at 90° to
the table as measured with the square (fi g. I2).
If the bevel pointer (88) does not indicate zero on the bevel scale (89),
loosen the screw (90) that secures the pointer and move the pointer as
necessary (fi g. I3).
Adjusting the fence (fi g. J)
The upper part of the left side of the fence can be adjusted to the left to
provide clearance, allowing the saw to bevel to a full 48° left. To adjust the
fence (7):
Loosen the fence clamping knob (91) and slide the upper part of the
side fence to the left.
Make a dry run with the saw switched off and check for clearance.
45

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D27107 T 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D27107 T 3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 15,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info