Active Vibration Control (Fig. 1)
D25223, D25323 AND D25324 ONL
The active vibration control r
hand and arm vibration allows for more comfortable use for longer periods of time and extends the
life ofthe unit.
For best vibration control, hold the tool with one hand on the main handle (B) and the other hand
on the side handle (I). Apply just enough pressur
The hammer only needs enough pressur
pressur
T
All rotary hammer drills ar
torque r
also prevents the gearing and electric motor fr
factory-set and cannot be adjusted.
Side Handle (Fig. 2)
WARNING: TAL operate the tool with the side handle
properly installed and securely tightened. Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold tool with both hands to maximize control.
A side handle comes assembled with this rotary hammer
both right-hand and left-hand users.
TO ADJUST THE SIDE HANDLE
1. Loosen the side handle (I) by turning it counterclockwise.
2. Rotate the side handle to the desir
3. Tighten the side handle by turning it clockwise.
TO CHANGE SIDES
For right-hand users: slide the side handle clamp over the chuck, handle at the left.
For left-hand users: slide the side handle clamp over the chuck, handle at the right.
T
T
switch.
NOTE: Use lower speeds for starting holes without a centerpunch, drilling in metal, plastics or
ceramics, or driving screws. Higher speeds ar
V
The variable speed trigger switch (A) permits speed control. The farther the trigger switch is
depressed, the higher the speed of the drill.
Lock-on Button (Fig. 1)
D25123, D25330
WARNING: Be sure to release the locking mechanism before disconnecting the plug from the
power supply
plugged in. Damage or personal injury could result.
The lock-on button (L) is for use only when the rotary hammer is stationary
stand or for chipping applications.
Before using the tool each time, be sur
freely
D25123 ONL
T
switch and slide the lock-off button (L) forwar
T
D25330 ONL
T
and push the lock-on button (L) in. The tool will continue to run.
T
Forward/Reverse Slider (Fig. 1)
D25123, D25213, D25313, D25223, D25323, D25324
WARNING: Always wait until the motor has come to a complete standstill before changing the
direction of rotation.
CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque.
The forward/r
jammed bits mode.
1.
forward (right-hand) r
2. Push the forwar
Mode Selector (Fig. 3)
D25123, D25213, D25313, D25223, D25323, D25324
NOTICE: T
damage to the tool may result.
DRILL-ONL
T
arrow points to the corr
plastics.
HAMMERDRILL MODE
Tthe mode selector button (E) and turn the mode selector (D) so the
yellow arrow points to the corr
HAMMER-ONL
For light chiseling, press the mode selector button (E) and turn the mode selector (D) so the yellow
arrow points to the corr
NOTE: The yellow arrow on the mode selector MUST be aligned with the one of the symbols at
all times. There ar
CHISEL ROT
D25313, D25323, D25324
T
arrow points to the corr
SDS Plus
®
Chuck (Fig. 1)
WARNING: T
from power source before making any adjustments or removing/installing attachments
or accessories.
WARNING: Burn Hazard. AL
the tool and bits may get extremely hot during operation. Small bits of broken material may damage
bare hands.
WARNING: Do not attempt to tighten or loosen drill bits (or any other accessory) by gripping the
front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur
T, insert shank of bit about 3/4" (19 mm), no further than 7/8" (22 mm) into chuck. Push
and rotate bit until it locks in place. The bit will be secur
T pull the chuck sleeve (F) back and r
OPERA
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury
WARNING: T
or clamped firmly If drilling thin material, use a wood “back-up” block to prevent damage to the
material.
T
properly installed and securely tightened. Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold tool with both hands to maximize control.
Proper Hand Position (Fig. 1, 4)
WARNING: TAL use proper hand position as
shown.
WARNING: TAL hold securely in anticipation
of a sudden reaction.
Proper hand position r
handle (B).
Overload Clutch
If the drill bit becomes jammed or caught, the drive to the drill spindle is interrupted by the overload
clutch. Because of the forces that occur as a r
hands and take a firm stance.
Drilling T
The machine is intended for hammerdrilling in concr
without impact in wood, metal, ceramic and plastic.
Chipping T
The machine is intended for chipping in concrete, brick and stone.
Removable SDS Plus
®
Chuck and Three Jaw Keyless Chuck
(Fig. 1)
D25324
The D25324 is equipped with a removable quick change SDS Plus
®
chuck as well as a removable
three jaw keyless chuck. The hammer mechanism does not function when the thr
chuck is used.
Both the SDS Plus
®
and three jaw keyless chuck can be easily r
(K) into the unlocked position to release the chuck.
The SDS Plus
®
and three jaw keyless chuck can be easily attached by inserting the chuck into the
spindle of the tool and turning the collar to the locked position. The chuck will click when properly
installed.
FIG. 5
J
H
I
FIG. 1
K
D25324
I
FIG. 2
D25330
A
L
M
I
Drilling
WARNING: T
from power source before making any adjustments or removing/installing attachments
or accessories.
WARNING: T ensure workpiece is anchored
or clamped firmly
material.
Press mode selector button (E) and turn the mode selector (D) to the drill bit symbol for drilling, to the
hammer symbol for hammering or to the hammerdrill symbol for hammerdrilling.
DRILLING OPERA
1.
speed steel twist drill bits or hole saws. Use a cutting lubricant when drilling metals. The
exceptions are cast ir
tipped bits or masonry bits. A smooth, even flow of dust indicates the proper drilling rate.
2.
biting, but do not push hard enough to stall the motor or deflect the bit.
3. Hold tool firmly with both hands to contr
WARNING: Drill may stall if overloaded causing a sudden twist. Always expect the stall. Grip
the drill firmly with both hands to control the twisting action and avoid injury
4. , it is usually because it is being overloaded. RELEASE TRIGGER
IMMEDIA, remove drill bit frDO NOT CLICK
TRIGGER OFF AND ON IN AN A
DAMAGE THE DRILL.
5. T
through the last fractional part of the hole.
6.
jamming.
7. With variable speed drills there is no need to center punch the point to be drilled. Use a slow
speed to start the hole and accelerate by squeezing the trigger harder when the hole is deep
enough to drill without the bit skipping out.
DRILLING IN MET
An SDS Plus
®
to round shank adaptor chuck is r
and the D25323. Ensure that tool is in drill-only mode. Start drilling with slow speed and incr
to full power while applying firm pressur
J
F
C
A
I
H
F
D
L
J
E
G
D25123
C
D
E
F
G
J
I
H
B
A
D25323
A
E
D
J
I
F
G
H
C
D25223
FIG. 3
DRILL-ONL
MODE PERÇAGE SEULEMENT
MODO SÓLO T
HAMMER/DRILL MODE
MODE PERFORA
MODO T
CHISEL ROT
ROT
ROT
(D25123, D25213, D25223 ONL
HAMMER-ONL
MODE PERFORA
MODO SÓLO MARTILLO
E
E
CHISEL ROT
ROT
ROT
(D25313, D25323, D25324 ONL
E
HAMMER/DRILL MODE
MODE PERFORA
MODO T
FIG. 4
